The armature of a 270V dc shunt motor has a resistance of 0.20 ohm. If the armature current is not to exceed 85 amp, calculate: (a) The resistance that must be inserted in series with the armature at the instant of starting. (b) The value to which this resistance can be reduced when the armature accelerates until the counter emf becomes 171 volts. (c) The armature current at the instant of starting if no resistance is inserted in the armature circuit.

The armature of a 270V dc shunt motor has a resistance of 0.20 ohm. If the armature current is not to exceed 85 amp, calculate: (a) The resistance that must be inserted in series with the armature at the instant of starting. (b) The value to which this resistance can be reduced when the armature accelerates until the counter emf becomes 171 volts. (c) The armature current at the instant of starting if no resistance is inserted in the armature circuit.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

The rated parameters of a separately excited DC motor are: U=420V; Ia=57,5A; Ra=0.1Ω and kgφ=0,4263 (V/rpm). Friction, ventilation and core losses of the motor is 600 W and can be considered as constant. a) Calculate the output power and torque of the motor at nominal operating condition. b) The motor drives a load having half of the rated torque at nominal speed. Calculate the armature current, induced voltage at armature windings and the power drawn from the supply. Ignore the power losses in the field circuit. May I ask for can you send the answer after being tottaly sure about the answer and can you give some little explanations for each step of your solution. Thanks in advance.
Describe simply, in one(1) sentence, how we can increase the value of the armature current in a shunt dc motor in the case of an increase in load while keeping the input power supply constant?
A separately excited motor runs at 1045rpm, with a constant field current, while taking an armature current of 50A at 120V. The armature resistance is 0.1 Ω if the load on the motor changes such that it now takes 95A at 120V, determine the motor speed at this load.
The rated parameters of a separately excited DC motor are: U=420V; Ia=57,5A; Ra=0.1Ω and kgf=0,4263 (V/rpm). Friction, ventilation and core losses of the motor is 600 W and can be considered as constant. Calculate the output power and torque of the motor at nominal operating condition. The motor drives a load having half of the rated torque at nominal speed. Calculate the armature current, induced voltage at armature windings and the power drawn from the supply. Ignore the power losses in the field circuit.
The rated parameters of a separately excited DC motor are: U=420V; Ia=57,5A; Ra=0.1Ω and kgf=0,4263 (V/rpm). Friction, ventilation and core losses of the motor is 600 W and can be considered as constant. Calculate the output power and torque of the motor at nominal operating condition. The motor drives a load having half of the rated torque at nominal speed. Calculate the armature current, induced voltage at armature windings and the power drawn from the supply. Ignore the power losses in the field circuit. May I ask for can you send the answer after being tottaly sure about the answer and can you give some little explanations for each step of your solution. Thanks in advance.
A 4 pole, 220V , DC shunt motor develops an output power of 10 kW . If Ra = 0.07 ohms , and Rsh = 105 ohms, the armature current is
(A Long shunt compounded DC motor has a nominal voltage of VT=100V. Its armature circuit total resistance is Ra= 3 ohm, serial field resistance Rs= 1 ohm. and shunt field resistance Rsh= 50 ohm . Find the shunt field circuit current (Ish) of the motor and write inside a box as given below, under rated load (full load) conditions. Draw the electrical equivalent circuit of the motor and write the resistance values of Ra, Rs and Rsh resistances on the correct places of the electrical equivalent circuit. Be careful about your solutions and drawings to be readable) Ish=?solve this question by using the rulers of Electromechanical Energy Conversion 2
A 500-volt dc motor is operating with an input current of 1.5 kA and at a speed of 47 rad/sec. The armature resistance is 0.07 ohms. Approximate the torque developed by this motor.
A 10hp, 230V, 1200 rpm DC series motor has the total armature circuit resistance Ra + Rf = 1.1Ω. The rotational losses of the machine is 640W. What is the armature current when the motor delivers its rated load at 1200rpm when connected to a rated supply voltage? What is the efficiency in percentage of the motor given in problem-above, at full load and rated speed?
The shunt field of a 5-hp dc compound motor has a resistance of 200 ohms, a series field resistance of 0.0018 ohms and an armature resistance of 0.5 ohms. If the motor develops a back emf of 200 V at a full load current of 50A, and a rotational loss of 400 W, determine: b. Ish (shunt field current)
ELECTROMECHANICAL ENERGY CONVERSION A shunt DC motor has a total resistance value for all conditions as Ra 2 0 and under full load conditions (nominal load) armature current is Ia - 10 A. The nominal terminal Voltage for the motor is VT 300 Vand total value for field circuit resistance for al conditions si Rf-150 . Under ful load conditions (nominal load), find the internal generated Voltage (EA), excitation circuit current (field current) (If), (total supply current flow, from electrical source) line current (li), electrical input power (Pin) supplied from the source.
The armature resistance of a compound direct current motor with short shunt is 0.15 , the series winding resistance is 0.25  and the shunt winding The resistance is given as 800 . The armature of the DC motor with a terminal voltage of 120 is 1400 rpm. If it draws 12 amps from the motor terminals while rotating, the torque produced by the motor and Find the efficiency of the engine.