The assembly consists of a bronze tube and a threaded steel bolt. The pitch of the thread is 1/32 in. (one turn of the nut advances it 1/32 in.). The cross-sectional areas are 1.5 in? for the tube and 0.75 in? for the bolt. The nut is turned until there is a compressive stress of 4000 psi in the tube. Find the stresses in the bolt and the tube if the nut is given one additional turn. Use E = 12 x 10° psi for bronze and E = 29 x 10° psi for steel. Bronze tube 40 in.

The assembly consists of a bronze tube and a threaded steel bolt. The pitch of the thread is 1/32 in. (one turn of the nut advances it 1/32 in.). The cross-sectional areas are 1.5 in? for the tube and 0.75 in? for the bolt. The nut is turned until there is a compressive stress of 4000 psi in the tube. Find the stresses in the bolt and the tube if the nut is given one additional turn. Use E = 12 x 10° psi for bronze and E = 29 x 10° psi for steel. Bronze tube 40 in.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A hollow steel [E = 30,000 ksi] tube (1) with an outside diameter of 3.00 in. and a wall thickness of 0.223 in. is fastened to a solid 1.75-in.-diameter aluminum [E = 10,000 ksi] rod. The assembly is attached to unyielding supports at the left and right ends and is loaded as shown. Assume P=18 kips, Q=13 kips, L1=4 ft, L2=6 ft, and L3=6 ft. Determine(a) the stresses in all parts of the axial structure.(b) the deflections of joints B and C.
A tripe-U shear mount used four 10 mm x 60 mm x 100 mm hard rubber blocks. Upon loading, the upper U framedeflected by 1.5 mm. The elastic modulus of rubber is 50 MPa. Determine the Poisson’s ratio of the rubber used.Determine the pressure between the rubber and the wall.Determine the Strain of Side KL.
Two forces, each of magnitude P, are applied to the wrench. The diameter of the steel shaft AB is 16.6 mm. Determine the largest allowable value of P (in N) if the shear stress in the shaft is not to exceed 89.31 MPa and its angle of twist is limited to 5.38˚. Use G = 80.35 GPa for steel and L = 455 mm. Round off the final answer to two decimal places.
A steel bracket of solid circular crosssection is subjected to two loads, each of which isP = 4.5 kN at D (see figure). Let the dimension variablebe b = 240 mm.(a) Find the minimum permissible diameter dminof the bracket if the allowable normal stress is110 MPa.(b) Repeat part (a), including the weight ofthe bracket. The weight density of steel is77.0 kN/m3.
4. The plate shown in the figure is fastened to thefixed member by seven 10-mm-diameter rivets.Compute the value of the loads P so that theaverage shearing stress in any rivet does notexceed 70 MPa.
A W18×86 beam is riveted tona W24×117 grinder by q connection as shown in the figure. The diameter of the rivets is 7/8 in, and angles are each 4×31/2×3/8 in. For each rivets assume that the allowable stresses are T= 15 ksi and stress in b is 32 ksi. What is the bearing strength of the grinder? What is the bearing strengtht of the beam? What is the shear strength of the rivets? What is the maximum load that the connection can carry?
A steel beam is bolted to a steel girder by a connection similar to that in the figure shown below. The diameter of the bolt is 10 mm, and the thickness of each angle bar is 4 mm. For each bolt, assume that the allowable bearing stress is 224 MPa. Find the allowable load in kN on the connection. Assume the thickness of the web of the beam to be 7 mm and the thickness of the web of the girder to be 8 mm The final answer should include two decimal places
The center post B of the assembly has an original length of 124.7 mm, whereas postsA and C have a length of 125 mm. If the caps on the top and bottom can beconsidered rigid, determine the average normal stress in each post. The posts aremade of aluminum and have a cross-sectional area of 400 mm Eal = 70 GPa. Detailed solution pls. Thank you!
please specify if the results are compression or tension. also please answer a-c
Given the following allowable stresses:• 50 MPa for shear in rivets• 100 MPa for bearing between a plate and a rivet• 80 MPa for tension in the platesNOTE: Draw FBD(a) If we increase the diameter of each bar to 20 mm, determine the maximum load Pthat can be applied to the lap joint.(b) Using the value computed for maximum load P from (a) compute for the over-allfactor of safety given that the actual P= 20kN.
A 15" x 3/8" bar of A572 Gr. 50 steel is used as a tension member. It is connected to a gusset plate with 7/8-in diameter bolts as shown in the figure. Use s = 2.0 and g = 3.0. a) Determine the allowable tensile strength of the section based on tensile rupture of the net area.b) Determine the allowable tensile strength of the section based on yielding of the gross area.
complete solution and drawing. if u can please add some explanation thankyou FN = 49 MN = 101 SN = 94 What will be the maximum weight of cylinder that can be put as shown in the figure below if the maximum stress at cable is FN mPa? Note: Round off your answer in two decimal places.