The axial and circumferential stress experienced by the cylinder wall at mid-depth (1m as shown) A cylindrical container of radius R= 1 m, wall thickness1 mm is filled with water up to a depth of 2 m andsuspended along its upper rim. The density of water is1000 kg/m3 and acceleration due to gravity is 10 m/s?.The self-weight of the cylinder is negligible. The formulafor hoop stress in a thin-walled cylinder can be used atall points along the height of the cylindrical container.1 mm2 m1 m2R-

Given data: Axial stress on side face will be due to force on the bottom face.

Answered: The axial and circumferential stress…

Engineering

Mechanical Engineering

The axial and circumferential stress experienced by the cylinder wall at mid-depth

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter8: Centroids And Distributed Loads

Section: Chapter Questions

Problem 8.122P: The 12-ft wide quarter-circular gate AB is hinged at A. Determine the contact force between the gate...

See similar textbooks

Related questions

Q: The cross-sectional area shown is subjected to V = 600 kN and M =1000 kN-m. What is the transverse…

Q: A cylindrical water tank a thickness of 0.6 inhas an internal pressure of 580 psi. a.If the tank…

Q: The value of shear stress in the principal plane is Resultant stress Maximum Zero O Minimum

Q: Two vertical forces are applied to the beam of the cross section shown. Determine the maximum…

Q: Determine the maximum normal stress (in Mpa) in bar ABCD if the cross-sectional area of the bar is A…

Q: The specification of a cylindrical vessel are as follows: D = 350 mm %3D t = 12 mm P = 4.5 MPa %D…

Q: The state of stress of an element is given. Determine its principle plane by the specialized…

Q: The cross-sectional area of bar ABCD is 600 mm2. Determine the maximum normal stress in the bar.…

Q: Determine maximum shear stress Maximum principal stress-44 MPa Minimum principal stress=38 Mpa

A: Given data : Maximum principal stress σ1=44 MPa Minimum principal stress σ2=38 MPa Required :…

Q: SIMPLE STRESSES 2. The puncher is to drive a 25 mm diameter hole to a steel plate. If the allowable…

Q: QUESTION 3: Determine the equivalent state of stress for an element oriented 60° counterclockwise…

Q: P=70 MPa . Determine maximum principal stress

Q: A composite bar consists of an aluminum section rigidly fastened between bronze section and steel…

A: Draw a labeled diagram of the given composite bar. Calculate the stress in the rightmost section…

Q: When filled to capacity, the unpressurized storage tank shown contains water to a height of h- 21…

Q: rectangular section the ratio of maximum shear stress to the average shear For a stress is

A: Given data : Rectangular section Width=B Depth=D Shear force=V Average shear stress=ζAvg Maximum…

Q: Forces are applied as shown at point D of the steel post shown.Since the diameter of the pole is 60…

Q: Question 12 A 7-ft diameter spherical tank is subjected to an internal pressure of 45 psf. If the…

Q: if the maximum and minimum principal stresses at a point are (27 Mpa) and (5 Mpa) respectively. The…

A: Maximum shear stress is equal to difference of maximum principal stress and minimum principal stress…

Q: 1- Calculate the stress at a-a and b-b sections. 1.2m a -30mm + 6. R=50 kN 0.&m 20M A

Q: Pulleys 1 and 2 of the rope and pulley system are connected and rotate as a unit. The radii of…

A: Given r1=0.1 m and r2=0.3 m d=0.015m m=225 kg Assuming no friction between any of the ropes and…

Q: Determine the maximum stress at the fillet of the filleted flat plate of 8 mm thickness as shown in…

Q: 39- The maximum shear stress in contact between two steel spheres a At the contact surfaceL b Under…

A: Option (a) is correct At the contact surface

Q: 48.0 in. and the wall thickness is 0.75 in. The tank is pressurized to 1.40 ksi. Determine the a

Q: Determine the normal stress in a basketball of 9.5-in. outer diameter and 0.125-in. wall thickness…

A: Given data: The outer diameter of basketball is d = 9.5 in. The thickness of basketball’s wall is t…

Q: Question 2 The bar has a cross-sectional area A and is subjected to the axial load P. Determine the…

Q: Module 4 Stress Distribution Point loads of 2000, 4000, and 6000 Ibs act at points A, B and C…

Q: 1. A water tank 3 m in diameter and 6 m high is made from a steel with thickness of 10 mm. a) When…

Q: A water tank made from a steel having a thickness of 12mm has the following dimensions. Internal…

Q: The internal pressure acting on the closed ends of a cyclinder causes a stress known as a. Hoop…

A: Hoop stress/Tangential stress:It is defined as the force acting perpendicular to each point of…

Q: 1) Determine the stress components acting on the inclined plane AB. 65 MPa /30 20 MPa

Q: 1. Determine the stresses for a square stress element on top of CD at point D. The stress element is…

Q: Determine maximum shear stress Maximum principal stress=25 MPa Minimum principal stress=-5 MPa

A: Maximum principal stress, σmax=25 M PaMinimum principal stress, σmin=-5 MPa

Q: 4) Mohr's circle is shown for a point in a physical object that is subjected to plane stress. If 1…

A: Given data: (Note: 1 grid square = 8 MPa) ● The stress in the negative x-direction: 10 grid square…

Q: The stresses shown act at a point in a stressed body. Assume stress magnitudes of Sx = 13,300 psi,…

Q: Find the normal stress of members CB and BF of the truss shown. Cross sectional area of the members…

A: GIVEN DATA - A PLANE TRUSS GIVEN WE HAVE TO FIND STRESS IN MEMBER CB AND BF

Q: The shear stress at the inner surface of hollow circular section is __

A: The shear stress at the outer surface of the hollow circular section is maximum and minimum at the…

Q: A thick-walled cylinder has an outer and inner diameter of 200 and 50 mm, respectively. The…

Q: An 8 mm thick cylindrical steel tank has an outside diameter of 600 mm and a length of 3 m. (a) when…

A: (a) The circumferential stress is 1.0889 MPa. (b) The longitudinal stress at the bottom is 0.5445…

Q: A hydraulic system is used to apply a force in an external fixation device to hold broken ends. The…

Q: 4- A water tank of 3 m dia. and 25 m high, is completely filled with water. Determine the required…

Q: Given the following plane element determine a. The principal stresses b. The principal angles (no…

Q: A smooth-walled 100 mm edge steel bucket is filled with rubber to form a rubber bucket embedded…

A: Given data: a=100 mmF=100 kNE=4 MPav=0.45 Need to determine the normal contact stress between the…

Q: Determine The Normal Stress In Each Member Of The Truss Structure Shown. 3. Material: Steel,…

A: The normal stress =43.56,52.9,49.6

Q: 4) Mohr's circle is shown for a point in a physical object that is subjected to plane stress. If 1…

Q: The normal and shear stresses acting on one plane passing through a point in a soil mass are 120 psi…

A: Among the applied normal stresses on mutually perpendicular planes the stress corresponding to…

Q: Charles Whitney replaced the curved stress block with an equivalent triangular block of intensity…

Q: Determine the absolute maximum shear stress of the stress state acting on the element shown in the…

Q: he cylindrical tank with a spherical end-cap has an outer radius of r=1.5m and a wall thickness of…

Concept explainers

Torsion

In mechanical engineering, torque, torsion, and twisting moment are three of the most important concepts which have different meanings. Torque is the consequence of a moment of a force that produces an angular acceleration in a body or induces rotational kinetic energy in a body. For instance, in an automobile, the power transmission shaft is a body that is always under rotation due to the external torque acting on it, this torque is created by the engine.

Question

The axial and circumferential stress experienced by the cylinder wall at mid-depth (1m as shown)

A cylindrical container of radius R= 1 m, wall thickness
1 mm is filled with water up to a depth of 2 m and
suspended along its upper rim. The density of water is
1000 kg/m3 and acceleration due to gravity is 10 m/s?.
The self-weight of the cylinder is negligible. The formula
for hoop stress in a thin-walled cylinder can be used at
all points along the height of the cylindrical container.
1 mm
2 m
1 m
2R-

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 3 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

The round handle of a faucet is affixed to a shaft that lets a valve to be open and closed every time the round handle is rotated. Give the radius of the handle if the shaft has a diameter of 1 cm and the MA of the machine is 8.
A hydraulic cylinder filled with water has an inside diameter of 1.0 in and a length of 2.0 ft. How many pounds of force must be applied to a piston at the end of the cylinder to compress the water by 0.1 in? Take the bulk modulus of water to be K=312,000 psi.
A thin-walled hollow sphere 3.8 m in diameter holds helium gas at 1767 kPa. Determine the minimum wall thickness of the sphere in mm if its allowable stress is 84.8 MPa.
A cylindrical pressure vessel has an inner diameter of 1.2 m and a thickness of 12mm. Determine the maximum internal pressure it can sustain so that neither itscircumferential nor its longitudinal stress component exceeds 140 MPa. Under thesame conditions, what is the maximum internal pressure that a spherical vessel with a similar inner diameter can sustain?
Determine the capillary action (rise or fall) of mercury in a capillary tube of diameter 1.5 mm. Surface tension is 0.514 N/m and contact angle is 140°.A. 7.87 mm rise C. 8.78 mm fallB. 8.78 mm rise D. 7.87 mm fall
A cylindrical pressure vessel has an inner diameter of 4 ft and a thicknessof 1 2 in. Determine the maximum internal pressure it can sustain so that neither its circumferential nor its longitudinal stress component exceeds 20 ksi. Under the same conditions, what is the maximum internal pressure that a similar-size spherical vessel can sustain?
A water filled pipe has water flowing at v1= 5.90 m/s in a section of pipe where the diameter is d1= 20.2 cm and the pressure is known to be P1= 7.00×104 N/m2 above atmospheric pressure. a. If the pipe carries the water 3.5 meters up hill without any change in diameter, what is the new absolute pressure within the pipe? b. After flowing up the hill described above, the pipe narrows to 80% of its original radius, what will be the new water velocity (v2) in the pipe? c. What will be the absolute pressure (P3) in the smaller pipe? d. What is the volume flow rate through the smaller pipe?
The density of seawater at a free surface where the pressure is 98 kPa is approximately 1030 kg/m3. Taking the bulk modulus of elasticity of seawater to be 2.34 × 109 N/m2 and expressing variation of pressure with depth z as dP = ?g dz determine the density and pressure at a depth of 2500 m. Disregard the effect of temperature.
Determine the magnitude and point of application of the horizontal and vertical compenents of the hydrostatic pressure force acting on the prismatic surface a b c d e. The surface lenght (dimension perpendicular to the figure) is 4.5 m. The unit weight of water =9.81 Kn/m3
A cylindrical steel tank having an internal diameter of 50 in. is submerged in seawater (weight density =64⁢ lb/ft3) to a depth of 9750 ft. The internal gage pressure in the tank is 1600 psi. (a) If the allowable stress of the steel is 32 ksi, what is the minimum allowable outside diameter of the tank? (b) What is the maximum tensile stress before the tank is immersed? Determine the external pressure of the seawater at a depth of 9750 ft. po= psi Determine the maximum magnitude of σr produced in the tank. σr = psi Based on the maximum magnitude of σr produced in the tank from Part 2, is there an outside diameter for which the radial stress magnitude will exceed the allowable stress of the steel in this case? More calculations are needed. No Yes For this case, choose the correct statement regarding the maximum magnitude circumferential normal stress. It occurs at the outer surface of the tank, and it is tensile. It occurs at the outer surface of the tank, and it…
Show the derivation of the girth and longitudinalstresses of the thin-walled cylindrical container shownbelow. Say p is the internal pressure, d is the insidediameter of the container, and t is wall thickness.
Déterminer la différence de pression Pa-Pb pour D1=330mm D2=160mm d3=480mm D4=230mm. Le poids spécifique de l'air est négligeable. Le poids spécifique de eau=9790N/m3Determine the pressure difference pa-pb for d1=330mm d2 =160mm d3=480mm d4=230mDetermine the hydrostatic force exerted on the door AB of dimensions (1m and 0.9m wide) and its point of application Q (distance between A and Q). the specific weight of water is 9790N/m3 and the density of the oil is 0.82m. the specific weight of air is negligible. the specific weight of water is 9790N/m3.