"the axis of this feature should be coaxial within .006 with the datum axis, as measured RFS with the datum RFS". also in feature control frame.

Q: sketch the orthographic view using catia v5, and i need the orthographic view in the first angle…

A: THIS FIGURE SHOWS THE ISOMETRIC VIEW AS GIVEN IN QUESTION AND DRAWN IN CATIA V5

Q: Question 1 (a) The three planes of 'orthographic' projection of an object are presented in Figure…

A: Please find the solution below

Q: Identify the following items for each of the datum targets: a) the datum reference, b) the specified…

A:

Q: Part I: Hand drawn plates using Graphical Position Analysis i) Specifications: Length (in) Theta…

A:

Q: I need these three parts answered pertaining to the print provided. If you can not answer all three…

A: Yes, it could be projected off of the view as all the necessary dimensions are mentioned in the…

Q: dy 3) 2- 2y + a = 0 (Separation variables). dx

A:

Q: Show Isometric View. Use Dimlinear for measurement 52 11 11 18 11 TOP VIEW 40 32 Ø16 - 36 32 Ø18 R16…

A:

Q: dong B. enin 670 50 10 45 30 70 15 10 88 040

A: The sectional view in the drawing is the view to show the hidden part of an object by cutting some…

Q: Problem 10.32 - Enhanced - with Hints and Feedback 9 of 11 I Review Consider the shaded arca shown…

A:

Q: Please put the dimensions and corners of the seen, for the drawing of the stereo, ISO metric

A:

Q: Top View (hrp) Front View (frp) Side View (prp)

A:

Q: Which of the twelve geometric controls is the most common? O Angularity O Position O Flatness O…

A: A feature control frame is used in GD&T to show the condition and tolerance provided in the…

Q: Question # 1: For the isometric shown below, draw with scale 1:2 and dimension the following views…

A: Orthographic Projection It is a form of presenting a three-dimensional object into Two dimensional.…

Q: Compute the distance from pixel p (10,3) to pixel q (28,30) using: a. Euclidean distance b.…

A:

Q: Give all the location dimensions between the datum target areas , A1 and A2. X = _________________,…

A: Give all the location dimensions between the datum target areas , A1 and A2.X =0  ,  Y =74   ,   Z =…

Q: Purpose: Gomplete missiag views, cauvert orthographie te isometrie Description: Hor each set of…

A: The given views are top and front  To sketch the side view  Isometric view

Q: skech the 3 projection views and the isometric view

A: The three projection views are the Top view Front view side view.

Q: GIVEN FRONT AND SIDE VIEW, SKETCH THE MISSING VIEW ALSO DRAW THE ISOMETRICVIEW USING AUTO CAD -16-…

A:

Q: 66 Through holes Through hole 70 sketch the orthographic view using catia v5, and i need the…

A:

Q: Draw missing view and iso metric 50 14

A: Orthographic Projection It is a form of presenting a three-dimensional object into Two dimensional.…

Q: sketch the top view ,side view and front view using catia v5, and i need the orthographic view in…

A:

Q: The given casted component is in isometric view ,for the casted component ,sketch the Orthographic…

A:

Q: Owhat is The ad vantageoFusing matrix méThod in Para x ral oPt i^cs? ob hain The sxstem matrix Por…

A:

Q: Draw the figure below by using the appropriate 3d commands, rectangular array, and other operations…

A: 3D angular array

Q: If my desired output rate is 75 units per hour, what is the efficiency of my setup? Aniwer to…

A: for solution refer below images.

Q: The three planes of 'orthographic' projection of an object are presented in Figure 1.1 below. Draw…

A: Draw the isometric block according to dimensions of the object as shown in the image:

Q: Q) Draw the following projections for the figure shown with scale 1:1. 1. Front View 2. Side View 3.…

A:

Q: Given TOP VIEW & FRONT VIEW sketch the side view and isometric view Note : Assume each unit as 10 mm

A:

Q: sketch the top view ,front view and side view using catia v5, and i need the orthographic view in…

A:

Q: Draw the following projections for the figure shown with scale 1:1. 1. Front View 2. Side View 3.…

A:

Q: Sketch the isometric and draw the orthographic view with neat arrangement ,it's better to do in…

A:

Q: SKETCH THE MISSING VIEW AND THE ISOMETRIC VIEW OF THE VIEWS GIVEN USING AUTOCAD 1.00

A:

Q: 77. Asketch of a manufactured part is given below the drawing. Sketch the planes of a datum…

A: The datum is defined as the locus surfaces or the starting points for the location and orientation…

Q: Sketch the missing view and isometric view of the attached figure Note : use creo parametric 3.0…

A:

Q: sketch the orthographic view using catia v5 , and i need the orthographic view in the first angle…

A:

Q: Calculate the minimum row spacing for a ground-mounted array in Las Vegas, NV. Assume the height of…

A: The given data are: θ=10°d=10 ft Here, θ denotes the angle and d denotes the distance.

Q: On the part shown, specify a geometric control to make the left surface in the front view…

A:

Q: I need these three parts answered, if you are unable to answer all three parts please leave it for…

A: In an auxiliary view the plane which is selected is not the principle projection planes (frontal,…

Q: What is the maximum "bow of the pin before any geometric control is applied, and what rule in…

A: The answer to the above mentioned question is given below

Q: 1.sketch the orthographic view using catia V5, and need the orthographic view in the first angle…

A:

Q: Sketch the isometric view for the othographic view given below using CATIA V5 ,NO HAND DRAWING

A:

Q: use AutoCAD to make a three-view drawing, complete with dimensions, of the part.

A: Orthographic Projection It is a form of presenting a three-dimensional object into Two dimensional.…

Q: . Draw it's projections in all possible positio

A: Given: A point is 50 mm from both the reference planes. To determine: Projections in all possible…

Q: 6. Give all the location dimensions between the datum target areas, A1 and A2 . Z = Page 1 of 3 7.…

A: The location dimension is an indication of the location of an object in a view. Observe the given…

Q: If the major diameter of a screw is 11.7 cm measured from the shadow master projector (with 10X…

A: The given diameter of the shadow of the screw is 11.7 centimeters. The magnification of the lens is…

Q: On the part above, specify a geometric control to make the left surface in the front view…

A: Specify a geometric control for the drawing

Automation in manufacturing processes

The term automation refers to the technique through which the creation of an apparatus takes place using an automatic process or a system. Let us try to understand this with an example.