25030/0PrivTer* Question Completion Status:87°FCloudyL4PA56Cross Section Area, A = 0.04 m²Axial Load, P = 171 KNAngle, 0 = 53°7#The bar is subjected to the axial load. There is a shaded section which is oriented at 0 from the horizontal.Given:810Moving to another question will save this response.LAADetermine the average normal stress (MPa) acting over the shaded section.Express your answer in 2 decimal places.$12 13 14 15 16%P>S(C17&1819hpW00206

Answered: Image /qna-images/answer/017bb3f1-e4a4-4c02-8628-89a2b3e4891e.jpg

The bar is subjected to the axial load. There is a shaded section which is oriented at 8 from the horizontal. Given: Cross Section Area, A=0.04 m² Axial Load, P= 171 KN Angle, 8= 53° P4 P Determine the average normal stress (MPa) acting over the shaded section. Express your answer in 2 decimal places.

The bar is subjected to the axial load. There is a shaded section which is oriented at 8 from the horizontal. Given: Cross Section Area, A=0.04 m² Axial Load, P= 171 KN Angle, 8= 53° P4 P Determine the average normal stress (MPa) acting over the shaded section. Express your answer in 2 decimal places.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Given: b = 350 mm d = 420 mm f'c = 30 MPa fy = 275 MPa Mu = 200 kN-m diameter of Rebar = 20 mm Required: 1 Depth of stress block, mm 2 Depth of the neutral axis, mm 3 Number of 20mm rebars
Determine the normal stress in each of the cables? (MPa) a. 85.7 b. 75.7 c. 65.7 d. 55.7 If the cables elongated by 1 mm, what is the vertical displacement of the precasat slab? (mm) a. 1.758 b. 1.658 c. 1.458 d. 1.558 What is the tensile force in each of the cables? (kN) a. 5.98 b. 4.98 c. 7.98 d. 6.98 SOLVE ALL AND WILL GET A LIKE <3 ps: unit weight of concrete is 24kn/m^3
A piece of engineering equipment is supported by thefoundation shown. The diameter of the circular pinis 20 mm. a.) Determine the value of P so as not toexceed the allowable bearing stress of310.5 Mpa in the circular pin.b.) Determine the value of P so as not toexceed the allowable shearing stress of 138Mpa in the circular pin.
Given: Mmax= 15.625 kN-m Vmax= 12.5 kN Depth of the beam= 250 mm 1. A simply supported 5 meter timber beam carries a 5 kN/m uniformly distributed load. If the beam's Ix is 260.4166 x 10^6 mm^4 and fb = 7.50 MPa, what is the base of the beam? a) 150 mm b) 180 mm c) 200 mm d) 220 mm 2. The shear stress fv developed for the beam of question 1 is a) 0.375 MPa b) 0.50 MPa c) 0.75 MPa d) 0.85 MPa
An open top standpipe as shown has a radius r= 2.2m and 20 mm wall thickness. Determine the height ? (?? ??????)of the water that will result to a circumferential stress of 24MPa in the wall of the standpipe. NOTE: The specific weightof water is 9.81???3. Remember, pressure is equals to the product of specific weight and height. Use 2 decimal places.
Given: 1. Structural Component: Beam 300 mm x 400 mm Column 400 mm x 400 mm Slab thickness 110 mm 2. Dead Load: Super Imposed dead load = 4.5 KPa (including slab weight) CHB = 3.11 KPa 3. Seismic Parameter: Soil Profile - Sb Closest distance to the source - 10 km Ductility Coefficient R = 8.0 Seismic Zone Z=0.40 Ct = 0.0731 A. Compute TOTAL LATERAL FORCES in the 2nd floor? B. Compute LATERAL FORCES in the 3rd floor?
A 10 ft x 15 ft rectangular area carrying a uniform load of 5000 psf is applied to the ground surface. Compute the vertical stress increment due to this load at a depth of 20 ft below the ground surface by the approximate method. a. 714 b. 232.49 c. 60 d. 144.8
Derive the general expression for Shear Stress and velocity istribution for laminar flow in pipe. Show that mean velocity of flow is half of maximum velocity of flow in the pipe.
CORRECT LETTER PLS 1. Which of the following least affects hydraulic gradient or slope of HGL? A. PIPE LENGTHB. PIPE DIAMETERC. TYPE OF PIPED. FLOE RATE 2. In laminar flow, which is correct?BJ: higher Re value has higher friction factorJB: lower Re value has lower friction factorGroup of answer choices A. BJ is false and JB is true B. BJ is false and JB is false C. BJ is true and JB is false D. BJ is true and JB is true 3. In a system with 4 reservoirs and 2 pipe junctions, how many continuity equations are formulate? A. 3B. 2C. 1D. 4E. 5
!!!Show Complete Solutions and FBD!!! What is the bending stress in the beam 1.8 meteres from point A?a. 9.60Mpab. 8.60Mpac. 7.68Mpad.10.24Mpa What is the bending stress 20 mm from the top of the beam 1.5 meters from point A? a. 9.247Mpab. 7.225Mpac. 10.442Mpad.4.838Mpa What is the shear stress in the beam at point A?a. 0.48Mpab. 0.33Mpac. 1.57Mpad. 0.80Mpa
Proivde the summary of the below ? General shear failure
Given: 1. Structural Component: Beam 300 mm x 400 mm Column 400 mm x 400 mm Slab thickness 110 mm 2. Dead Load: Super Imposed dead load = 4.5 KPa (including slab weight) CHB = 3.11 KPa 3. Seismic Parameter: Soil Profile - Sb Closest distance to the source - 10 km Ductility Coefficient R = 8.0 Seismic Zone Z=0.40 Ct = 0.0731 A. Compute the DESIGN BASE SHEAR (V = Cv*I*W /R*T). B. Compute the Minimum DESIGN BASE SHEAR (V =0.11Ca*I*W).