The beam is constructed from two boards fastened together at the top and bottom with two rows of nails as shown. If an internal shear force of V = 10 kN is applied to the boards and the nails are made with a material having allowable shear stress of 75 MPa, determine the minimum diameter of each nail. 100 mm 100 mm 50 mm 50 mm 150 mm

The beam is constructed from two boards fastened together at the top and bottom with two rows of nails as shown. If an internal shear force of V = 10 kN is applied to the boards and the nails are made with a material having allowable shear stress of 75 MPa, determine the minimum diameter of each nail. 100 mm 100 mm 50 mm 50 mm 150 mm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

ASAP PLEASE. 4 DECIMALS What is the value of R1 in kN? What is the value of R2 in kN? Locate the point of zero shear from point A in meters.
Find shear force value under point load 10 Kn
Calculate the vertical shear stress (N / cm2) at point A in the critical section of the beam below whose load and section is given? The cross section is symmetrical with respect to the y-axis. (Point A is on the body, point B is on the x-axis and point C is on the header.) (Q = 6000 N / m, P = 60000 N, L = 3 m, b = 50 cm t = 5 cm, h = 20 cm) please fast help please
A floor slab 100 mm thick is cast monolithically with beams 300 mm wide 500 mm deep spaced 2 m on centers, on simple supports over a span of 6.0 m. The floor supports a superimposed service dead load of 1.77 kPa and service live load of 4.8 kPa. Using f’c = 21 MPa, long bar fy = 415 MPa, calculate: Using a T-beam geometry, determine the required amount of flexure bars for maximum ultimate bending. = [As] sq.mm (whole number)
A wooden beam is fabricated by nailing together three pieces of dimension lumber, as shown. The cross-sectional dimensions of the beam are also shown. The beam must support an internal shear force of V = 750 lb. Assume b1=2.00 in., b2=3.75 in., d1=8.00 in., d2=1.50 in.(a) Determine the maximum horizontal shear stress in the cross section for V = 750 lb. [Answer: 34 psi]
Determine the maximum tensile stress and maximum compressive stress due to the load P acting on the simple beam AB (see figure). Data are as follows: P= 5.4 kN L=3.0 m d=1.2 m b=75 mm t_=25 mm h=100 mm h1=75 mm c1=62.5 mm c2=37.5 mm, and l= 3.3203x10⁶ mm⁴
A steel plate 2.5 m x 1.6 m x 100 mm thick is to be hoisted by a steel cable sling as shown in the figure. Assume the steel weighs 77.3 kN/cu.m. Determine the shear stress (MPa) in the 16 mm diameter pins through the clevis The correct answer is 45.33. Show solution.
the horizontal bar shown (length = 15.0 feet) rests on smooth indines. compute the distance X at which load T = 250 lbs should be placed from point B to keep the bar horizontal
Q: A cantilever beam of length L = 2 m supports a load P = 8.0 kN (as shown). The beam is made of wood with cross-sectional dimensions 120 mm x 200 mm. Calculate the shear stresses due to the load P at points located 25 mm, 50 mm, 75 mm, and 100 mm from the top surface of the beam. From these results, plot a graph showing the distribution bottom of shear stresses from top of the beam.
A beam is constructed from three boards bolted together as shown. Determine the shear force developed in each bolt if the bolts are spaced s=250 mm apart and the applied shear force is V=39kN.
The beam is made from four boards nailed together as shown. If the nails can each support a shear force of 100 lb., determine their required spacing s and if the beam is subjected to a shear of V = 700 lb.
Give all numerical values at all change of loading positions and at all points of zero shear. Use the following scale for the diagrams: SHEAR DIAGRAM: 1 cm = 100 kN; MOMENT DIAGRAM: 1 cm = 100 kN-mGiven: F1 = 72; F2 = 30; F3 = 150; F4 = 60a) What is the value of R1 in kN?b)What is the value of R2 in kN?c) Locate the point of zero shear from point A in meters