A wooden beam is constructed from three boards which are nailed together as shown in the figure. The spacing between the nails is 75 mm. If the wooden beam has an allowable shear stress of Tw = 7MPa and if each nail can resist a shear of 3 kN, determine the maximum lods P that can be applied to the end of the beam. 250 mm 3 kN 100 mm 75 mm 250 mm A B 2m 2m 50 mm 50 mm

A wooden beam is constructed from three boards which are nailed together as shown in the figure. The spacing between the nails is 75 mm. If the wooden beam has an allowable shear stress of Tw = 7MPa and if each nail can resist a shear of 3 kN, determine the maximum lods P that can be applied to the end of the beam. 250 mm 3 kN 100 mm 75 mm 250 mm A B 2m 2m 50 mm 50 mm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

26 -The stair beam in the figure will have support reactions. A support is a fixed, B support is a sliding joint. loads P1= 15 kN, P2= 30 kN, dimensions a = 2 m, b = 6 m, c = 4 m. Accordingly, Ax = ?A) 30B) 18.75C) None.D) 3.75E) 0
Calculate the member force on member HF in Kips? Specify if T or C. 87.6 C 105.9 C 79.7 C 97.5 C 112.1 C
Given a 2.0meter Wide Flange steel compression member with A=4832mm2, Ix=88951759mm4 and Iy=3223498mm4 with Fy = 345MPa. Calculate the allowable strength in KN if both ends are hinged or pinned. Express your answer in 2 decimal places.
Hello, can someone help me with this pls. Determine the vertical component of the force applied at the joint to keep the plate in equilibrium. For the exercise use a value of "a" equal to 39.4mm and a value "P" equal to 1217.9N
A line is recorded as 472.90 m long. It is measured with a0.65 kg tape which is 30.005 m long at 20 °C under a 50N pull supported at both ends. During measurement, thetemperature is 5 °C and the tape is suspended under a 75N pull. The line is measured on 3% grade. E = 200 GPa,cross-sectional area of tape is 3 mm2 and the coefficientof linear expansion is 0.0000116 /°C. Compute:a. The actual length of tape during measurement.b.The total error to be corrected for the inclined distancec.The true horizontal distance
What is the internal force in member AD? A. 750 N , T B. 450 N , T C. 750 N , C D. 450 N , C SHOW SOLUTIONS
A beam is constructed from three boards bolted together as shown. Determine the shear force developed in each bolt if the bolts are spaced s=250 mm apart and the applied shear force is V=39kN.
a0 () o 2 20210612.. > A beam is constructed from three boards nailed together as shown in Fig. . If each nail can support a shear force of 45 Ib. if the largest vertical shear of 100 lb for the beam, determine the maximum spacing s of the nails for each case (a) and (b) il 3 > mil (€ 3in osin ™, 0sin » t | |« osin | osin 6in 6in ¥ 05in 1 0sin case (a) case (b)
A cantilever beam AB with a rectangular cross section has a longitudinal hole drilledthroughout its length (Figure 3). The beam supports a load P = 600 N. The cross sectionis 25 mm wide and 50 mm high, and the hole has a diameter of 10 mm. Find the bendingstresses at the top of the beam, at the top of the hole, and at the bottom of the beam.
Calculate the vertical shear stress (N / cm2) at point A in the critical section of the beam below whose load and section is given? The cross section is symmetrical with respect to the y-axis. (Point A is on the body, point B is on the x-axis and point C is on the header.) (Q = 6000 N / m, P = 60000 N, L = 3 m, b = 50 cm t = 5 cm, h = 20 cm) please fast help please
The T section shown is formed by joining two rectangular pieces of wood together. The beam is subjected to a maximum shearing force of 60 kN. All dimensions are in mm . A.) Which of the following gives the moment inertia in x 10^6mm^4 at the neutral axis? Choices: 8.56,14.26,10.57,21.52 B.) Which of the following gives the shearing stress at the neautral axis? Choices: 3.21,4.64,3.95,4.28 C.) Which of the following gives tge shearing stress in MPa at the junctiin between two pieces of wood? Choices: 31.78,21.42,28.32,16.52
A 30m steel tape weighing 1.45kg is of standard length under a pull of 5kg, supported for full length. A line 938.55m long was measured using the tape with a steady pull of 10kg. If E=2.0x106kg/cm2 and unit weight of steel is 7.9x10-3kg/cm3, determine: a) cross-sectional area of the tape b) CP c) Correct length of line