The beam is loaded as shown in the figure. The supporta at A is pin, and B is roller. Determine the following: A a. Determine the support and pin reactions of the beam shown below. b. Sketch its shear and moment diagrams. c. Determine the value and location of maximum shear and moment of the beam. Hinge -10 m D B --5 m- C 25 kN/m -15 m- D E -+-5m-+-+- Hinge -10 m-

The beam is loaded as shown in the figure. The supporta at A is pin, and B is roller. Determine the following: A a. Determine the support and pin reactions of the beam shown below. b. Sketch its shear and moment diagrams. c. Determine the value and location of maximum shear and moment of the beam. Hinge -10 m D B --5 m- C 25 kN/m -15 m- D E -+-5m-+-+- Hinge -10 m-

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Determine the moment at D in kip-ft for the beam shown below using the three-moment equation. Express your final answer in two decimal places. Consider signs
From the beam shown below: Compute for the Reactions, Draw the Beam and Draw the Shear and Moment Diagram under the Beam. Note: Include the proper units/dimensions and round off the answers to 3 decimal places.
For the frame shown, determine the support reactions. EI is constant.Use the force method. I have a correct answer, it is: VA = 36.30 kN (↑); HA = 19.30 kN (→); VB = 18.70 kN (↑); HB = 11.30 kN (←). To the left); B (right). I don't know how to get to this result, please show me how to get there step by step
In the overhanging beam show, determine P so that the moment over each support equals the moment at the midspan. W= 3.7 kN/m. Round your answer to 2 decimal places.
Draw the shear and bending moment diagrams for the beam shown. EI is constant. Use the force method. I have the right answer, it is: VA = 2.90 kN (↑); HA = 0 kN; VB = 6.30 kN (↑); VC = 0.40 kN (↑). To the left); B (right). I don't know how to get to this answer, please show me step by step.
Determine the reactions in pounds the hinge and the rocker exert on the beam supporting the distributed load. (Assume that the +x-axis is to the right and the +y-axis is up along the page. Due to the nature of this problem, do not use rounded intermediate values in your calculations.) Ax=0 Ay=? By=? Magnitude and direction
Determine the moments at the support of the beam shown. Use moment Distribution method. 1.a Mb 1.b Mc 1.c Md
Replace the force system by a wrench and specify the magnitude of the force and couple moment of the wrench and the point where the wrench intersects the x–z plane.
Use the VIRTUAL WORK method. a.) determine the vertical displacement of joint A. Each bar is made of steel and has a cross-sectional area of 600 mm^2. Take E= 200 GPa. b.) why solving the reactions of the supports is not needed or necessary?
The shear-force diagram for a simple beam is shown in the figure. Assume that no couple is applied to the beam. a) Draw and label the moment diagram. b) Draw and label the load diagram. c) Give the value of the maximum moment.
For the beam loaded as shown, do the following: 1. Determine the values of shear and moment at points where change in loads occur using the Area Method. Mark maximum values. 2.Draw the shear and moment diagram. Show computation. 3. Solve the moment of inertia of the cross-section of the beam about the neutral axis. Show computation and box your answer.
The following two questions refer to the beam below and the following values: w1 = 0.5, w2 = 0.1, l = 25, and a = 8. Give numerical answers to one decimal place. a. What is the negative moment at the roller (absolute value)?b. What is the moment at the point of maximum moment in Fig. 18 of the NDS moment diagrams (the value of moment at this point is marked "M1")? Give your answer with the correct algebraic sign.