Answered: The beam with, cross-section shown, is…

The beam with, cross-section shown, is subjected to the load shown. Using E=200 GPa, determine a. the value of Ely at B and D b. the deflection at B and D 80 mm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: 1. The weight of the reinforced steel in a foundation should be from__________ of the weight of the…

A: The percentage of steel used in the foundation range from 0.12% to 0.15% by volume. The density of…

Q: A block is pushed against a horizontal spring, compressing it to 22 cm. After being released, the…

Q: The flow of river is 750 ft3/sec and site is 100 ft. It is desired to developed a maximum capacity…

A: step 1-

Q: Mass of crate: 100 kg μk: 0.25 Determine the maximum compression, x. k = 2 kN/m 10 m 45°

Q: Identical steel bars are used to support a 7400-N load as shown. For the properties of steel bar: A…

Q: Fill in the blanks Smaller angle: Larger angle: s = 20 ft Determine the two possible angles so that…

Q: SITUATION. Three forces act on a rigid body namely: F₁= 25kN acts from A (0, 1, 2) to B (2, 3, 5).…

Q: An A992 Gr. 50 W21x132 is used to carry the load shown in the figure. The beam is laterally…

Q: A special case of kinematics that is refer to straight- line velocity. A rectilinear B) plane motion…

Q: rectangular beam having a width of 250 mm has a total depth of 450 mm. It is reinforced at the…

A: step 1-

Q: If the direction is constant, the motion of the body follows a straight-line path and is called A…

A: 1) Answer: B) Rectilinear translation Explination: If motion of body follows straight line path…

Q: Find all reaction for the Freame by slope Deflection method W henge в An W2² 12 4m T 3M 3 м

Q: s = 20 ft Determine the two possible angles so that the water strikes at B. CA=40 ft/s 4 ft 2 8 ft

Q: (b) A rectangular channel 3.05 m wide carries 3.4 m3/s uniform flow of water at a depth of 0.6 m.…

Q: TYPEWRITTEN ONLY PLEASE. ILL UPVOTE ONLY IF TYPEWRITTEN, COMPLETE, AND CORRECT. DONT ANSWER IF YOU…

Q: Mass of the plane: 150,000 kg Initial velocity 0 Final velocity: 100 m/s Distance traveled: 500 m…

A: mass of plane = 150000kg = 1471 kn s = 500m U = 0m/s V = 100m/sec

Q: 2230 kN 80 mm 1.75 m X 90 mm Z 2230 kN Y

Q: Please help! I need the answer immediately. A W14 × 74 flexural member of ASTM A992 steel is used as…

A: Given Data: W14 × 74

Q: 10-21. and D are pins. El is constant. Determine the reactions at the supports. Assume A 15 ft 20 ft…

A: Given :

Q: ELEV. 130m 2 B L = 1000m D = 200mm f = 0.023 L = 1500m D = 250mm L = 300m ELEV. = 40m f = 0.02 D =…

Q: Example 10.6 An embankment is to be formed with its centre line on the surface (in the form of a…

A: Solution-The given values are as followsThe width(b)=40ft The depth (d1)=10ft(d2)=20ft…

Q: center from the center of the bigger flange is: a) 31.56 mm

A: This question has been taken from engineering mechanics

Q: Q8. What is liquid limit of soil.

A: Liquid Limit

Q: - 1 attachment- Determine the maximum height, h, perpendicular to the ground. h 55.30 ft/s² 25° B…

Q: A car starts from rest and accelerates at a constant rate in a straight line. In the first second…

Q: Given a cantilever beam, determine the slope and deflection at point A. El is constant. 30 KN/m A B…

Q: From the previous problem, determine the shear stress 30 mm above the neutral axis.

Q: , determine the maximum shearing stress c

A: This question has been taken from Steel structures

Q: A uniform T-section beam is 100 mm wide and 150 mm deep with a flange thickness of 25 mm and a web…

Q: 5. The section of a concrete gravity dam is 3m at the top with a base of 5m and a height of 8m. The…

A: Stability analysis for gravity dams often is simplified into a two-dimensional rigid body analysis…

Q: Find the limiting peripheral velocity of a rotating steel ring if the allowable stress is 20 ksi and…

Q: A cantilever beam has a span of 4m and carries a uniformly distributed load throughout its span.…

Q: Three pipes, pipe 1, pipe 2 and pipe 3, are connected in series. Pipe 1 has diameter of 600mm and…

Q: s = 20 ft Determine the two possible angles so that the water strikes at B. VA= 40 ft/s 4 ft 8 ft

Q: Example (Introduction to Geotechnical Engineering by Robert D. Holtz) Given: Soil profile 0 A brown…

Q: EXAMPLE 11.2 Calculate the station of the BC and EC. You are given the following information:…

A: Given R= 400 m ∆ = 12051' =12.85°

Q: In Figure Question 5 . The 2nd street is eastbound with offsets of+ 15 s between successive…

A: Offset The Offset is the lateral measurement taken from an object to the chain line. Objects are…

Q: Required information A 90° elbow in a horizontal pipe is used to direct water flow upward at a rate…

Q: closed traverse is as follows:

A: Given: Station X (Easting) Y (Northing) 1 0 0 2 53 56 3 108 115 4 165 177 5 224 242 6…

Q: Determine FEMAB of the beam with uniform varying load of 23 kN/m, 1 meter from the left fixed…

Q: A pump pumps 0.200 ft³/s of brine solution having a density of 1.15 g/cm³ from an open feed tank…

A: Given -

Q: The horizontal member shown in the figure is loaded by 57 kN at E. It is supported by steel…

Q: What is Mn of the beam? (Lbs - Ft for units) Determine if the beam can adequately support the…

A: Given Data: The compressive strength of the masonry is fc'=2000 psi. The tensile strength is fy=60…

Q: What should be the observation and analysis for sieve analysis of fine aggregate if the value of…

A: Fineness Modulus 3.7 Cu= 4.1 Cc= 1.1 % error = 1.8% Cu= 4.1 between 4-6 Hence well graded sand Cc=…

Q: The state of stress at a point is shown with respect to the xy-axes. Determine the equivalent state…

A: step 1-

Q: Determine the slope at A and displacement at C. El is constant. 5 kN-m B C -1.5 m. −1.5 m

Q: Example 9.5 Calculate the area of the underground roadway from the measurements given. Assume the…

Q: - 1 attachment Determine the maximum height, h, perpendicular to the ground. h 55.30 ft/s2 25° 35°

Q: 2. Is there a difference between the values of the water jet force on plate (F₁) when change the…

A: Fluid mechanics : Fluid mechanics is the department of classical physics and arithmetic worried with…

Q: Example 10.6 An embankment is to be formed with its centre line on the surface (in the form of a…

A: Calculating A1 First let us find the area of the triangle on the sides of the embankment in A1. By…

Concept explainers

Beams

In structural engineering, a beam is a component made of a variety of materials (including steel alloys, and wood) that can resist loads applied laterally to the beam axis. Members, elements, rafters, shafts, and purlins are all terms used to describe beams.

Question

The beam with, cross-section
shown, is
subjected to the load shown. Using E-200
GPa, determine
a. the value of Ely at B and D
b. the deflection at B and D
80 mm
►
4 kN/m
16 KN
25 mm
B
D
6m
4m
2m
Using Moment-Area Method
25 mm
140 mm
I
25 mm
120 mm

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step 5

Step by step

Solved in 5 steps with 5 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

22 Determine the plastic moment strength (kN-m) of a C10x30, A572 Gr. 50 steel, about the minor axis. d = 254 mm bf = 80.52 mm tw = 12.95 mm tf = 12.73 mm A. 16.85 B. 27.46 C. 19.74 D. 23.44
A simply-supported T-beam is subjected to two pairs of distributed loads: pair 1 (wD1, wL1)and pair 2 (wD2, wL2). The geometric, material and loading properties are all given on thetable above. bf=1368mm bw=408mm t=248mm fc'=25.2MPa fy=336MPa d=918mm d'=92mm Lbeam=12.2m wD1=42.2kn/m wL1=50.2kn/m wD2=170.2kn/m wL2=193.3kn/m1. Solve for the height of the compression stress block using pair 1. 2. Solve for the theoretical steel area using pair 1. 3. Using Es = 0.004, solve for the theoretical steel area using pair 2. 4. Using Es= 0.005, solve for the theoretical steel area using pair 2.
A simply supported beam is loaded. Use E = 29 x 10³ ksi and I = 550in⁴. Using moment area method determine the following: A. Slope at the 8k load B. Location of the maximum deflection C. Maximum value of the deflection Use four decimal places
A cantilever beam with P1=63kN, P2=49 kN and w=36 kN/m has the loadings shown. Calculate the maximum deflection in terms of EI. Answer: -7.749.5867 Need solution
The simply supported beam consists of a W14 x 34 structural steel wide-flange shape [E - 29,000 ksi; I - 340 in.*]. For the loadingshown, use discontinuity functions to compute (a) the slope of the beam at E and (b] the deflection of the beam at C. Assume wo - 8kips/ft, WCD - 4.5 kips/ft, LAB - 7.5 ft. Lac - 7.5 ft. LCD - 10.5 ft, LDE - 4 ft.W.CD
The beam shown is fixed at A and to be supported by rod BC at B. The beam carries a uniform load w = 24 kN/m throughout its 5-meter span. E = 200 GPa and I = 450 x 106 mm4. What is the maximum deflection at the free-end without the rod?
22 Determine the plastic moment strength (kN-m) of a C15x40, A992 steel, about the minor axis. d = 381 mm bf = 89.41 mm tw = 13.21 mm tf = 16.51 mm A. 36.24 B. 30.98 C. 43.11 D. 50.41
36 -Loading status in figure q= 4 kN ⁄ m, P = 48 kN in the bar dimensions L= 2 m and e= 0.5 m. The cross-sectional effects at point E will be calculated. A is fixed, B is sliding joint bearing. Accordingly, By=? a) 0B) 48C) 24D) NoneE) 14
The rigid frame is subjected to the distributed load and point load as shown in the diagram. IAB = 500in4 IBC = 800in4 ICD = 500in4 E = 29,000ksi Using the method of virtual work for frames, determine the horizontal deflection at roller A.
Read the question carefully The W360 x 79 simply supported beam is made of A-36 steel and is subjected to the loadingshown. Using the superposition method, calculate (a) the Slope at A, (b) the maximum Deflection ofthe beam and at center.
Determine the maximum deflection of the simply supported beam. E=200GPaE=200GPa and I=69(10^6)mm4I=69(10^6)mm4
Question:- A 7.5 meters long simply supported structural steel beam carries two concentrated loads P at every third points. Use A 572 Grade 65 steel with Fy=448.18 MPa. The beam is W310x23.8 section having the given properties. A=3040mm² d= 305mm tw= 5.6mm bf=101mm tf= 6.7 mm Ix= 43x10⁶ mm⁴ Iy=1.2x10⁶mm⁴ a) Calculate the allowable bending stress of the compression flange of beam 7.5 fully supported against lateral movement. b) Based from the previous question, calculate the value of concentrated load P that the beam could support safety.