The bolts in the figure below are being subjected to shear by a vertical reaction. The sheer will act tangentially on a transverse section through each bolt. Determine the average shearing stress in the bolts if the reaction is 75 kN and the diameter of each bolt is 25 mm.

The bolts in the figure below are being subjected to shear by a vertical reaction. The sheer will act tangentially on a transverse section through each bolt. Determine the average shearing stress in the bolts if the reaction is 75 kN and the diameter of each bolt is 25 mm.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter7: Analysis Of Stress And Strain

Section: Chapter Questions

Problem 7.2.13P: Two steel rods are welded together (see figure): the seam is oriented at angle ? = 50°. The stresses...

See similar textbooks

Related questions

Q: per the attached figure: if the applied shear force V = 14 kip, determine the maximum shear stress…

A: For the given block the neutral axis from top is,

Q: In the clevis shown in the figure, determine the minimum bolt diameter and minimum thickness of each…

A: Given: Determine : The minimum bolt diameter and minimum thicknessof each yoke.P = 55 kN , shearing…

Q: 6. The steel shaft of a socket wrench is 12 mm in diameter and 450 mm long (see figure). If the…

Q: 3.2-1 A copper rod of length L 18.0 in. is to be twisted by torques T(see figure) until the angle of…

Q: The steel shaft of a socket wrench has a diameter of 8.0 mm and a lengthof 200 mm (see figure).If…

A: As we know that, GφL=τd/2φ=2τ0LGd here, G is the shear modulus of the material, d is the shaft…

Q: The butt joint shown in the figure is connected using five 20 mm diameter bolt. If the tension force…

Q: A certain circular shaft is subjected to a maximum equivalent bending moment of 36,000 in-lb and a…

Q: A 55-mm-diameter solid circular shaft as shown in the figure is made up of an aluminum material. The…

A: Given; d= 55 mmτ= 75 MPaG = 29 GPaθA/C=0.065 rad

Q: In the figure, a double shear occurs at 20mm diameter pin at B, what is the shearing stress? In…

Q: Each of the four links in Figure has an 8x36mm uniform rectangular cross section and each of the…

A: Consider the free body diagram as shown below for the link ABC. From the moment equilibrium about…

Q: 4 ft Calculate the average shear stress in MPa of the pins B and C on the frame shown in the figure.…

Q: When drilling a hole in a table leg, a furnituremaker uses a hand-operated drill (see figure) with…

A: The shear stress in the bar, when it is subjected to torsional moment can be calculated using the…

Q: A heavy-duty helical spring is to be made by wrapping a steel rod 10.6 mm in radius around forming…

Q: A flanged bolt coupling consist of six 10 mm diameter steel bolts on a bolt circle 300 mm. in…

Q: PROBLEM 2. A structure shown in the figure weighs 3 kN/m each member supported by hinges at A and C.…

Q: 1. In the figure, assume that a 20-mm diameter rivet joins the plates which are 100 mm wide. a. If…

A: P= Stress x Arivets P=80[1/4 π (202)] P=8000 π N From bearing of plate material:P=σbAb 8000 π = 140…

Q: 600 G0° 70 mm

Q: Calculate the shear stress and the angle of twist (in degrees) for a thin-walled steel tube (G=76…

A: Given data: The modulus of rigidity, G=76 GPa. The length of the tube is, L = 1.5 m. The applied…

Q: 2. An equilateral triangle pipe, as shown in the figure has a uniform thickness of 1.5 mm. The…

A: The section is an equilateral triangle. It is symmetrical . And thus the centroid lies on the plane…

Q: Two blocks of wood, width w and thickness t, are glued together along the joint inclined at the…

Q: The shaft consisting of steel and aluminum segments carries the torques T and 2T as shown in the…

A: Answer: The largest allowable torque T is 691.1504 N•m.

Q: A part of gear box shaft shown in fig 3 transmit (40 kw) power through the gear located at (C). The…

A: Given, PB = 15 kW E = 200 GPa ν=0.3 f = 6 Hz

Q: A load P is supported by two springs arranged in series as shown in the figure. The upper spring has…

A: The total elongation is given as - δ = 64PR3nGd4upper + 64PR3nGd4lower76 = 64P×753×2083×103×194 +…

Q: A solid bar having a diameter 150 mm is to be replaced by a square tube having a cross-sectional…

Q: In figure as shown below, assume that a 35mm diameter rivet joint the plates which are each 150mm…

Q: 4. A round steel shaft rotates at 200 rpm while delivering 5000 W to a gear producing a bending…

Q: The butt joint shown in the figure is connected using five 20 mm diameter bolt. If the tension force…

Q: For the pin-connected structure in the figure, determine the minimum diameter for the pin at joint D…

Q: The composite shaft shown in the figure is manufactured by shrink-fitting a steel sleeve over a…

Q: the butt joint shown in the figure is connected using five 20mm diameter bolt. If the tension…

A: Given data: P=25 kNd=20 mm Need to determine the maximum shearing stress developed in the bolts.

Q: 4) The thin walled cross-section, shown in figure, has an allowable shear stress of 2 ksi. Determine…

Q: Calculate the shearing stress in pin A of the bulldozer if the total forces acting on the blade are…

A: Two forces acting on the blade is 8K and 4K We can find the shear stress in each pin

Q: The T section shown in the figure is the cross section of a beam formed by joining two rectangular…

A: The force which is applied parallel to a cross-section is termed as shear force and the stress which…

Q: 5. A flanged bolt coupling consists of eight 10-mm- diameter steel bolts on a bolt circle 400 mm in…

Q: On the figure below, determine the following: 1. Maximum bearing stress at joints ( bolts and…

Q: For the given systems below, plot shearing force and bending moment diaggrams. Show the critical…

Q: A 28mm diameter steel shaft AB is built into a rigid wall at A and supported by a smooth bearing at…

Q: 45 mm B 60 mm 30 mm 2 m -1.2 m

Q: Situation 1| Consider the figure 1 below. 3 - 25mmØ bolts are used to fasten a plate to a steel…

Q: Problem 2: It is recommended to change the circular cross section shown in the figure by a square…

Q: 3. (A). Define the terms shear stress and shear strain, illustrating your answer by means of a…

Q: Q3: A part of gear box shaft shown in fig 3 transmit (40 kw) power through the gear located at (C).…

Q: SAMPLE PROBLEM 300mm Py - 90 - The figure shows an eccentrically loaded bracket. P=20 kN. Bolt…

A: Bolt is defined as the material have to join the two materials like fasteners and thread together.…

Q: 2 ft The members of the structure in the figure weigh 200 lb/ft. Determine the smallest diameter pin…

Q: Q3: The web of a girder of I-section is 45 cm deep and 1 cm thick; the flanges are each 22.5 cm wide…

A: We are given the following data: Shear force, F=200 kN Section, I-Section

Q: A hydraulic punch press is used to punch a slot in a 0.30-in.-thick plate, as illustrated in the…

A: Given:Thickness of plate, t=0.3 inshear stress at plate, τ=36 ksid=1.25 ina=2.25 in

Q: If the wood joint shown in the figure has width of 200 mm, determine the average shear stress…

Q: -1.5m Q: Aluminum shaft of 30mm diameter and 1.5m lenght is subjected to a torque of 500N.m as in…

Q: A shaft composed of segments AC, CD, and DB is fastened to rigid supports and loaded as shown in the…

Concept explainers

Torsion

In mechanical engineering, torque, torsion, and twisting moment are three of the most important concepts which have different meanings. Torque is the consequence of a moment of a force that produces an angular acceleration in a body or induces rotational kinetic energy in a body. For instance, in an automobile, the power transmission shaft is a body that is always under rotation due to the external torque acting on it, this torque is created by the engine.

Question

section through each bolt. Determine th
stress in the bolts if the reaction is 15 kips
each bolt is1 in.
11
111
11
Figure 4-2 Be
(b)
stresses across the
(a)
4-4M. The bolts in Figure 4-2 are being subj
will act tange

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 5 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

The state of stress on an element along the hydraulic lift cylinder on a truck is trv= — 5 MPaLFind the maximum shear stress on the clement and show the state of stress on a sketch of a properly oriented clement.
Two steel rods are welded together (see figure): the seam is oriented at angle ? = 50°. The stresses on the rotated element are sx1=10 ksi, sy1= -12 ksi, and tx1y1= -5 ksi. Find the state of plane stress on the clement if it is rotated clockwise to align the x3 axis with the longitudinal axis of the rods.
Help ASAP Determine the tensile stress in the upper plate at section b-b in mpa 3decimals
8-2. Determine the state of stress on an element at the same point oriented 30° clockwise with respectto the element shown. Sketch the results on the element.
The axial assembly consists of a solid 1-in.-diameter aluminum alloy [E = 11000 ksi, v = 0.26, α= 10.5 × 10−6/°F] rod (1) and a solid 1.49-in.-diameter bronze [E = 15300 ksi, v = 0.15, α= 7.6 × 10–6/°F] rod (2). Assume L1=11 in., L2=22 in. If the supports at A and C are rigid and the assembly is stress free at 16°F, determine:(a) the normal stresses σ1, σ2 in both rods at 213°F (positive if tensile, negative if compressive).(b) the displacement uB of flange B (positive if to the right, negative to the left).(c) the change in diameter Δd1 of the aluminum rod.
he state of stress at a point in a member is shown on the element. Take σx = -3 ksi , σy= 4 ksi , τxy = -3 ksi . A) Determine the shear stress component acting on the inclined plane AB. Solve the problem using the method of equilibrium. B) Determine the normal stress component acting on the inclined plane AB. Solve the problem using the method of equilibrium.
A column has an outside diameter, D = 550 mm, an inner diameter, d = 150 mm.Determine the average normal stress developed on the cross section if the load, F is1890 kN.
a) The normal stress in bar BD is most nearly b) The shear stress in the pin at D is most nearly c) The shear stress in the pin at C is most nearly
USE the mohr's circle method to determine the stress components acting on the inclined plane AB USE THE MOHR'S CIRCLE METHODE NOT THE ONE IN THE QUESTION
NEED ANSWER ASAP !!! The axial load 274 kN applied to the lap joint is distributed equally among the three 26.5-mm-diameter rivets. What is the bearing stress (in MPa) between a plate and a rivet if w = 135.4 mm and t = 29.5 mm?
answer the following: what is the required P (in kN) to exactly close the gap between C and D? if P= 200 kN what is the axial stress of the steel member? NOTE: include the free body diagram.
The connection is made using a bolt and nut and two washers. If the allowable bearing stress of the washers on the boards is (sb)allow = 2 ksi, and the allowable tensile stress within the bolt shank S is (st)allow = 18 ksi, determine the maximum allowable tension in the bolt shank. The bolt shankhas a diameter of 0.31 in., and the washers have an outer diameter of 0.75 in. and inner diameter (hole) of 0.50 in.