The boom AC is a 4-in. square steel tube with a wall thickness of 0.25 in. The boom is supported by the 0.7-in .-diameter pin at A, and the 0.31-in .-diameter cable BC. Neglecting the weight of the boom, determine the shear stress in the pin (in psi) if P = 5383 lb. Round off the final answer to two decimal places. el 0007 P.png 70° 4 in 3.5 in 12 ft

The boom AC is a 4-in. square steel tube with a wall thickness of 0.25 in. The boom is supported by the 0.7-in .-diameter pin at A, and the 0.31-in .-diameter cable BC. Neglecting the weight of the boom, determine the shear stress in the pin (in psi) if P = 5383 lb. Round off the final answer to two decimal places. el 0007 P.png 70° 4 in 3.5 in 12 ft

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Determine the maximum horsepower a solid steel shaft 2.25in in diameter can transmit at 250rpm if the working stress in shear is 11,000lb/sq.in.
H.W The uniform thin pole has a weight of 50 N and a length of 26m. If it is placed against the rough wall and on the rough box in the position d= 10 m, us =0.3 at points A, B and C P= 150 N Box weight= 100N Determine the distanice x when the motion of the pole impend
The section of the masonry dam is as shown. The specific weight of water is 9.81 kN/m^3 and that concrete is 23.54 kN/m3. Determine the following: a. The resisting moment b. The factor of safety against overturning c. The factor against sliding if the coefficient of friction is 0.60
The maximum force that holds the 4-m-width gate in Figure Q2 (b) close is 50 kN. If oil is being added steadily, determine the maximum h before the gate starts to open. SGoil = 0.86.
Determine support reaction. Given a=5 m b=10 m P=30 KN
1. The boom of the wall crane 4m long is held at right angles to the wall by a wire that is attached to the wall 3m above the foot of the boom. If the load lifted is 45000N, find the tension in the wire and the compression force in the boom Neglect the weight of the boom. Draw the FBD
Write legibly and box the final answer. Determine the maximum mass (kg) that can be lifted at E if the 11.670-HP motor A has a maximum rotation speed of 301.20 rpm where the diameter of the shaft AB and CE are 10.237 mm and 15.402 mm, respectively. The allowable shearing stress is 1.001 GPa with F.S. of 1.76 for both shafts. Neglect the deformation of the cable at E. Where: radius of the gear at B, rB = 113.10 mm radius of the gear at C, rc = 158.58 mm
The pipe of weight W is to be pulled up the inclined plane of slope a using a force P. If P acts at an angle Φ, show that for slipping P = W sin(a + θ)/cos(Φ - θ), where θ isthe angle of static friction; θ = tan-1 μs.
A 5-m STEEL SHAFT ROTATING AT 2Hz HAS 70 KW APPLIED AT GEAR THAT IS 2m FROM THE LEFT END WHERE 20 KW ARE REMOVED.AT THE RIGHT END, 30KW ARE REMOVED AND ANOTHER 20 KW LEAVES THE SHAFT AT 1.5m FROM THE RIGHT END. (A) FIND THE UNIFORM SHAFT DIAMETER SO THAT THE SHEARING STRESS WILL NOT EXCEED 60 MPa. (B) IF A UNIFORM SHAFT DIAMETER OF 100mm IS SPECIFIED, DETERMINE THE ANGLE BY WHICH ONE OF THE SHAFTS LAGS BEHIND THE OTHER END. USE G = 83 GPa.
The boom DF of the jib crane and the column DE have the uniform weight of 750 N/m. If the hoist and load weigh 1500 N, determine the resulting internal loadings in the crane on cross sections through points A, B, C. (10
If the center of gravity of the stacked tables is at G,and the stack weighs 100 lb, determine the smallestforce P the boy must push on the stack in order tocause movement. The coefficient of static friction atA and B is μs = 0.3. The tables are locked together. P = _____________
If a horizontal force of F = 50 N is applied perpendicular to the handle of the lever at E, determine the clamping force developed at G. The mean diameter and lead of the single square-threaded screw at C and D are 25 mm and5 mm, respectively. The coefficient of static friction is μs = 0.3.