A small aluminum alloy [E=77 GPa] tee shape is used as a simply supported beam as shown. For this beam, a = 160 mm. The cross- sectional dimensions of the tee shape areb-22 mm, d = 33 mm, and t-4 mm. After loads are applied to the beam at B, C, and D,a compressive normal strain of 410 uɛ is measured from a strain gage located at c 10 mm below the topmost edge of the tee stem at section 1-1. What is the applied load P?

A small aluminum alloy [E=77 GPa] tee shape is used as a simply supported beam as shown. For this beam, a = 160 mm. The cross- sectional dimensions of the tee shape areb-22 mm, d = 33 mm, and t-4 mm. After loads are applied to the beam at B, C, and D,a compressive normal strain of 410 uɛ is measured from a strain gage located at c 10 mm below the topmost edge of the tee stem at section 1-1. What is the applied load P?

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter1: Introduction

Section: Chapter Questions

Problem 1.5.5P: The results of a tensile test are shown in Table 1.5.2. The test was performed on a metal specimen...

See similar textbooks

Similar questions

The data in Table 1.5.3 were obtained from a tensile test of a metal specimen with a rectangular cross section of 0.2011in.2 in area and a gage length (the length over which the elongation is measured) of 2.000 inches. The specimen was not loaded to failure. a. Generate a table of stress and strain values. b. Plot these values and draw a best-fit line to obtain a stress-strain curve. c. Determine the modulus of elasticity from the slope of the linear portion of the curve. d. Estimate the value of the proportional limit. e. Use the 0.2 offset method to determine the yield stress.
A tensile test was performed on a metal specimen having a circular cross section with a diameter 0. 510 inch. For each increment of load applied, the strain was directly determined by means of a strain gage attached to the specimen. The results are, shown in Table: 1.5.1. a. Prepare a table of stress and strain. b. Plot these data to obtain a stress-strain curve. Do not connect the data points; draw a best-fit straight line through them. c. Determine the modulus of elasticity as the slope of the best-fit line.
The results of a tensile test are shown in Table 1.5.2. The test was performed on a metal specimen with a circular cross section. The diameter was 3 8 inch and the gage length (The length over which the elongation is measured) was 2 inches. a. Use the data in Table 1.5.2 to produce a table of stress and strain values. b. Plot the stress-strain data and draw a best-fit curve. c. Compute the, modulus of elasticity from the initial slope of the curve. d. Estimate the yield stress.
A square beam (w=0.03 m) is loaded with a point load of 1000 N and a moment load of 1000 Nm, as shown. i. Determine maximum deflection of the beam using step by step analytical equations. ii. Determine the Maximum stress in the beam using step by step analytical equations iii. For both top fibers and bottom fibers of the square beam, specify the type of the stresses.
A beam having a tee-shaped cross section is subjected to equal 18 kN-m bending moments, as shown. Assume bf = 125 mm, tf = 25 mm, d = 185 mm, tw = 20 mm. Find the following: A. The cross-sectional dimensions of the beam are also shown. B. determine the maximum bending stress (positive if tensile and negative if compressive) produced in the cross section. Express your answer in MPa rounded to the nearest tenths. C. determine the bending stress at point H (positive if tensile and negative if compressive). Express your answer in MPa rounded to the nearest hundredths. D. determine the controlling section modulus about the z axis. Express your answer in (103) mm3 rounded to three significant figures. E. determine the moment of inertia about the z axis. Express your answer in (106) mm4 rounded to three significant figures.
For the figure shown below, If the bending working stresses are 15 ksi in tension and 18 in compression, compute the maximum safe value of P in kips
A rod with a cross-sectional area of 0.5 in2 is composed of three sections: steel, aluminum, and bronze rigidly attached with each other, aluminum being at the center of the three. Axial loads are applied as follows: 12,000 lbs. going out of steel and 3000 lbs. going out of aluminum. Dtermine the stress in steel, aluminum, and bronze respectively. Draw the free-diagram.
A rigid bar AB is hinged at A and is supported by a rod CD at C. The rod is pin connected at D, as shown. Neglect deflections of the bar due to bending. Use E=200 GPa. If the allowable stress in rod CD is 120 MPa, what weight W in kgs can be safely applied?
A hollow aluminum tube used in a roof structure has an outside diameter d2= 112mm and an inside diameter d1= 80mm. The tube is 2.80m long, and the aluminum has a shear modulus of G= 28GPa.a. If the tube is twisted in pure torsion by torques acting at the ends, what is the angle of twist, in degrees,when the maximum shear stress is 52MPa?b. What diameter d, in mm, is required for a solid shaft, as shown, to resists the same torque with the same maximum stress?c. What is the ratio of the weight of the hollow tube to the weight of the solid shaft?
A steel rod of length = 3m, diameter = 300 mm and modulus of elasticity = 200 GPa is inserted into an aluminum tube. The aluminum tube as length = 2999.95 mm, wall thickness of 20 mm and modulus of elasticity of 70 GPa. a.) Determine the deformation of each member due to axial compressive force P = 100 KN. b.) Determine the stress in each member. c.) Determine the axial strain if no gap exists.
Two solid cylindrical rods AB and BC are welded together at B and loaded as shown. Determine the magnitude of the force P (in lb) for which the tensile stress in rod AB is thrice the magnitude of the compressive stress in rod BC if Q = 20.11 lb.
When an axial load is applied to the ends of the two-segment rod shown in Figure P2.1, the total elongation between joints A and C is 7.5 mm. The segment lengths are a = 1.2 m and b = 2.8 m. In segment (2), the normal strain is measured as 2,075 um/m. Determine:(a) the elongation of segment (2).(b) the normal strain in segment (1) of the rod. (Ans. to check: Normal strain (1) = 825uE