A joint is made by gluing two plywood gussets of thickness t = 0.51 in to wood boards. Determine the tensile stress for the plywood (in psi) if the dimension b = 12.31 in and the applied force is P = %3D 6664 lb. Round off the final answer to three decimal places. W 016 shear on glue.png 1.75 in. -- Hート→ P 5.75 in.

A joint is made by gluing two plywood gussets of thickness t = 0.51 in to wood boards. Determine the tensile stress for the plywood (in psi) if the dimension b = 12.31 in and the applied force is P = %3D 6664 lb. Round off the final answer to three decimal places. W 016 shear on glue.png 1.75 in. -- Hート→ P 5.75 in.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The T section shown is formed by joining two rectangular pieces of wood together. The beam is subjected to a maximum shearing force of 60 kN. All dimensions are in mm . A.) Which of the following gives the moment inertia in x 10^6mm^4 at the neutral axis? Choices: 8.56,14.26,10.57,21.52 B.) Which of the following gives the shearing stress at the neautral axis? Choices: 3.21,4.64,3.95,4.28 C.) Which of the following gives tge shearing stress in MPa at the junctiin between two pieces of wood? Choices: 31.78,21.42,28.32,16.52
Determine the tension at AC. A. 55.23 kN B. 52.53 kN C. 32.55 kN D. 25.35 kN
It is obtained by fixing 4 wooden planks to each other with nails.given as a cross section. 2 verticals forming the sectionplank 20 mm X 80 mm, the other two planks 20 mm X 120 mmin size. between the nails fastening the planksthe distance is s = 50 mm. allowed on each nailThe safe cutting force is 300 N.a) The highest vertical that the beam can safely carryWhat is shear force?b) The maximum amount formed in the section corresponding to this shear force.What is high shear stress?
1. Find the resultant of tension F and Ta. 27.6 kNb. 37.2 kNc. 33.7 kNd. 44.6 kN2. What is the angle that their resultant makes with the horizontal rod OA? a. 28 degb. 37 degc. 33 degd. 44 deg3. Find the weight, W to prevent uplift. Use a factor of safety of 2.5. a. 49.23 kNb. 42.86 kNc. 59.51 kNd. 44.72 kN
Calculate the vertical shear stress (N / cm2) at point A in the critical section of the beam below whose load and section is given? The cross section is symmetrical with respect to the y-axis. (Point A is on the body, point B is on the x-axis and point C is on the header.) (Q = 6000 N / m, P = 60000 N, L = 3 m, b = 50 cm t = 5 cm, h = 20 cm) please fast help please
•Timber beamSafe working stress = 25 MPaCross-section dimensions:height = 119 mm,width = 66 mmProving ring number 293. Steel beam Safe working stress = 200 MPa Cross-section dimensions:external height = 149 mm,external width = 50 mm,wall thickness = 3.0 mm,Proving ring number 1522.1)Calculate safe max bending moment in the central part of the beam using Mmax = (I)(max stress)/(D/2)2) calculate Safe applied force in the proving ring or tie rod, assuming a symmetrical setup as in the photowith a ‘lever arm’ of 600 mm
A line is recorded as 475.25 m long. It is measured with a 6.5 N tape which is 30.492 m long at 680F under a 10 lb. pull supported at end points. During measurement the temperature is 4.50C and the tape is suspended under a 71 N pull. The line is measured on 3% grade. What is the true horizontal distance? Modulus of elasticity of the tape is 1.93 X 108 KPa and cross-sectional area of tape is 0.0284 cm2. Coefficient of expansion of the tape material is 0.0000116 m/0C.
P = 12 KIPS In a section ABC, sufficiently far from the post to remain plane, determine the stress at corner A.
Determine the magnitude of the 15 points force in member CD using method of section * (O 35.3KN Tension O none of the above (O 15.02KN Tension () 27.7 KN Compression (O 13.83 KN Tension O 16.2 KN Compression
.15 2.16 The three forces acting on the beam can be replaced with a single equivalent force R. Determine the angle θ and R. 25kN P2 60 kN P3 80 kN 40° 50° 4 m 6 Figure P2.16 COMPANY
A steel bar having cross-sectional areaA=1200mm2 is compressed by an axial loadP=53 kN.Determine the average normal and shear stressesacting on aninclined sectionaa cut through the bar at angleα=250.(Point K is a fixed support) A=5, B=3, C=8
Given: Mmax= 15.625 kN-m Vmax= 12.5 kN Depth of the beam= 250 mm 1. A simply supported 5 meter timber beam carries a 5 kN/m uniformly distributed load. If the beam's Ix is 260.4166 x 10^6 mm^4 and fb = 7.50 MPa, what is the base of the beam? a) 150 mm b) 180 mm c) 200 mm d) 220 mm 2. The shear stress fv developed for the beam of question 1 is a) 0.375 MPa b) 0.50 MPa c) 0.75 MPa d) 0.85 MPa