The brushes are ride on  _________ part of the armature.

Q: List the missing parts Reciprocating motion Crank mechanism

A: A connecting rod in the engine is used to connect the piston with the crank rod. one end is attached…

Q: The wrong maintenance procedure followed while performing gib adjustment on a lathe machine is O…

A: The correct maintenance procedure for gib adjustment on the lathe machine Adjust the gib to new…

Q: Under staticload or when static load is applied ,most of the machine elements re failed  True…

A: Under staticload or when static load is applied ,most of the machine elements re failed  True  False…

Q: What are the four movement that to be checked in a propeller loose blade

A: given; What are the four movement that to be checked in a propeller loose blade.

Q: cker mechanism rocking angle of 70 degrees. What are the lengths of the 4 bars in inches

A: A four-bar crank-rocker mechanism rocking angle of 70 degrees. What are the lengths of the 4 bars in…

Q: Match the following. Screwing is an example of Lapping is an example of

A: Solution:

Q: what is the impact of mechanical vibration on following a. Bearing House of Lathe machine b.…

A: Answer         c. Fatigue life of materials

Q: Which part of the drilling machine holds the job while performing drilling operation Select one: O…

A:

Q: used between slides and slideways are designed to keep out cutting fluids from falling into the…

A:

Q: These are the basic parts of the centrifuge, EXCEPT* A. drive shaft B. rotor C. barrel D. motor

A: The centrifuge is a mechanical device that is used to seperate the different components of the…

Q: List down the safety precaution need to carry during the operation of drilling?

A:

Q: clearance in the assembly

A: Given; In an interchangeable assembly, shafts of size = 25.00-0.0100-0.040mmsizes of  holes=…

Q: What part of an engine or Turret lathe slides move in the direction normal to the beds Ways

A: Given:- Turret lathe To find:- The part that moves in the direction normal to the bed of the bed

Q: what pushes the baulk ring into the cone on the gear when the sleeve  start to move on the hub ?

A: What pushes the baulk ring into the cone on the gear when the sleeve start to move on the hub

Q: 21:compare • Packed Hole Assembly • Pendulum Assembly • Fulcrum Assembly

A: Bottom hole assembly  There are numerous components and equipment (including the drill bit) that are…

Q: What is a wet mounts?

A: A procedure that is performed in a laboratory to observe motile organisms in wet mounts. It is an…

Q: The following device is used to hold a workpiece securely during drilling in Drilling machine Select…

A: It is required determine which of following device is used to hold a workpiece during drilling…

Q: what parts provide for toe-out on turns

A: Toe-out on turns is a toe setting for the front wheels so that it can make turns. While making a…

Q: During drilling operation, work piece must be held in vice. Select one: True False

A: Given Statement : During drilling operation, work piece must be held in vice. Select one: True…

Q: List the four main parts of the engine lathe

A: Given Engine lathe To find Four main parts Lathe is machine tool which is used to machine workpiece,…

Q: Fulcrum can be only  located at one end of the lever.

A: Fulcrum can be only  located at one end of the lever.

Q: What are the advantages of the hydraulic ram?

A: A hydraulic ram is an instrument that can transfer liquid (especially water) from a lower energy…

Q: Worn teeth on a speed gear can cause?

A: worn teeth creates a big problem in gear drive.

Q: What type of drill machine can be used in hand-held mode?     a)Micro drill b)Upright drill c)Radial…

A: Given data : Drill machine Hand-held mode

Q: After draining gear oil from a transaxle, the techniciannotices that the oil has shiny, metallic…

A: For a transmission or axle to last longer, it needs to be properly lubricated. After the required…

Q: Precautions before operating centre lathe

A: The Centre Lathe is a machine which is used to make a cylindrical shapes from a range of materials…

Q: Wipers pads on lathe machines are used between slides and slideways cannot be cleaned using…

A: The answer for above multiple choice question is “TRUE”

Q: The wrong maintenance procedure followed while performing gib adjustment on a lathe machine is On…

A: The engine lathe is a high-precision machine tool that needs to be treated with care. The lathe's…

Q: What is the phenomenon that occurs for the purpose of collecting snow on the chock valve 15:25

A: Chock valve is a mechanical device which is used to control the flow of a fluid. It acts as a…

Q: Where are the application of slider crank mechanism?

A: This question is based on the concept of slider crank mechanism.

Q: what maximum angle can the ramp make with the horizontal before the block starts to slip down?

A:

Q: A chain saw will run in many positions. Tech a says that this is because of its float type…

A: A chain saw will run in many positions because of its diaphragm type carburetor. Diaphragm allows…

Q: Creo Software to perform the assembly operation for a shaft and hole system. Hint: you can choose…

A: we have to demonstrate the assembly feature in creo parametric

Q: List down the safety precaution need to carry during the operation of drilling machine?

A: During the operation of drilling we need to take two types of safety precautions: 1. Fire Hazards…

Q: Before energizing the motor of a drill press, always ensure that the: Chuck key is placed in the…

A: To find : what needs to ensured before energising the motor of a drill press

Q: Safety goggles are required when working on lathe machine. Select one: True False

A: Lathe machine is one of the oldest machine used in manufacturing field. Due to its It's versatile…

Q: Helical gear

A: Ans is Helical gear

Q: 30. The methods of overhaul differ from maintenance procedure. a. True b. False

A: Note: Since you have asked multiple question, we will solve the first question for you. If you want…

Q: When removing or installing bearing, where should force be applied

A: The application of force during installation or removal of bearing is one of the critical factors,…

Q: Describe tapper noise

A: Ther is a concept called tappet noise When the engine is running ideally there comes a regular…

Q: The 3 basic oil seal designs to keep fluids from escaping around a rotating shaft are?

A: The three basic oil seal design to keep fluid from escaping around a rotating shaft are-

Q: Identify a true statement while maintaining wiper pads used on lathe machine

A: The Wiper pads are used for cleaning the small piece of the chips which can not be cleaned by the…

Q: The wrong maintenance procedure followed while performing gib adjustment on a lathe machine is The…

A: Given: The wrong maintenance procedure followed while performing gib adjustment on a lathe machineis

Q: The tap drill should be equal in diameter to the minor diameter of the se True/False (select one…

A: Since you have asked multiple questions, we will solve the first question for you. If you want any…

Q: Describe the three types of safing sensors.

A: The safety sensor is in charge of preventing unintended deployment of the airbags. The front…

Q: Why should the machine be kept clean and properly oiled?

A: To explain: The reason behind the machine to be kept clean and properly oiled. Explanation: The…

Q: The copper head hammer is used for releasing hold pin in the chuck. Select one: True False

A: The copper hear hammer is a hammer in which striking portion of the hammer (or head) are…

Q: 2.... Hydraulic controlled riveting assembly machine. hydraulic control system. Must include the…

A:

Q: What is the overall height of Tailstock?

A: To Find the overall height of Tailstock?