The bucket is hoisted by the rope that wraps around a drum wheel. If the angular displacement of the wheel is 8 = (0,3(1³) + 9,8t) rad, where t is in seconds, a) determine the velocity of the bucket when t = 3,1 s. Express your answer in ft/s. 0.75 ft Fuente: Hibbeler, 12th Ed. >) determine the acceleration of the bucket when t = 3,1 s. Express your answer in ft/s².

The bucket is hoisted by the rope that wraps around a drum wheel. If the angular displacement of the wheel is 8 = (0,3(1³) + 9,8t) rad, where t is in seconds, a) determine the velocity of the bucket when t = 3,1 s. Express your answer in ft/s. 0.75 ft Fuente: Hibbeler, 12th Ed. >) determine the acceleration of the bucket when t = 3,1 s. Express your answer in ft/s².

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The rod OA rotates in the horizontal plane such that =0.66t3 radian, and collar B is sliding outward along OA so that r=114t2 mm. If in both cases t is in seconds, determine the radial component of velocity (mm/s) of the collar when the collar is 128 mm from O. Round off only on the final answer expressed in 3 decimal places. DONT ROUND OF IN THE ENTIRE SOLUTION, ONLY IN THE FINAL ANSWER
Two inclined shafts are connected by means of a universal joint. The speed of the driving shaftis 1000 £p.m. If the total fluctuation of speed of the driven shaft is not to exceed 12.5% of this, what is the maximum possible inclination between the two shafts? With this angle, what will be the maximum acceleration to which the driven shaft is subjected and when this will occur ? [Ans. 20.4° ; 1570 rad/s? ; 41.28°]
The bucket is hoisted by the rope that wraps around a drum wheel. Ifthe angular displacement of the wheel is θ= (0.5t3 + 15t) rad, where tis in seconds, determine the velocity and acceleration of the bucketwhen t = 3s.
The flywheel rotates with an angular speed of w = 8 rad/s and an angular velocity = 16 rad/s2. Determine the tangential velocity at point B.
Determine the angular velocity, in rpm, of the rotating drum which results in loss of contact between the clothes and the drum at 1.0239 rad. Assume that the small vanes prevent slipping until loss of contact. Round your answer to 2 decimal places
The rod OA rotates in the horizontal plane such that 0.44t3 radian, and collar B is sliding outward along OA so that r=79t2 mm. If in both cases t is in seconds, determine the transverse component of velocity (mm/s) of the collar when the collar is 117 mm from O. Round off only on the final answer expressed in 3 decimal places.
(The complete question is in the picture) A disk rotates with constant angular acceleration about an axis passing through its center of mass. At an instant, its angular speed is measured to be 20.0 [rad/s]. What is the angular speed of the disk after 2.00 [s] if it has revolved by 60.0 [rad] during this timeinterval? A. 10.0 [rad/s]B. 20.0 [rad/s]C. 30.0 [rad/s]D. 40.0 [rad/s]
The brake drum is attached to a larger flywheel that is not shown. The motion of the brake drum is defined by the relation 0-36t-1.6t², where is expressed in radians and t in seconds. Determine (a) the angular velocity at t = 2 s, (b) the number of revolutions executed by the brake drum before coming to rest.
The angular velocity of the disk is defined by ω=(7t2+4)rad/s, where t is in seconds. A) Determine the magnitude of the velocity of point A on the disk when t = 0.8 s . B) Determine the magnitude of the acceleration of point A on the disk when t = 0.8 s
Assuming there is no slippage for the belt assembly below, Determine the following: What is the average angular velocity of each pulley if the rope accelerates from 5 m/s to 10 m/s in 10 s? How many revolutions does the pulley turn in that time? R1 = 0.3 m R2 = 0.2 m R3 = 0.1 m
15.9 A 0.6-m radius drum carrying the load A is rigidly attached to a 0.9-m pulley carrying the load B as shown. At the time t=0, the load B moves with velocity of 2 m/s downward and a constant acceleration of 3 m/s2 downward. Over the time, 0 is less than or equal to t and 2 is greater than or equal to t, s determine (a) the number of revolutions executed by the pulley displacement of the load A.
When studying whiplash resulting from rear-end collisions, the rotation of the head is of primary interest. An impact test was performed, and it was found that the angular acceleration of the head is defined by the relation a= 700 cos0 + 70 sin 0, where a is expressed in rad/s2 and 0 in radians. Knowing that the head is initially at rest, determine the angular velocity of the head when 0= 30°.