1000 RPM500 RPM3000 RPM200 RPM From the speed chart below, determine the correct cutting speed for performing a facing cut on Brasswith a milling machine using a 0.5 in. diameter ball-nose end-millSurface Speed(Ft/Min)400Aluminum 300Brass/BronzeLow Carbon SteelCast Iron200100807060Alloy Steel 5040Diameter(in)www.100.40.30.20.1Cutting Speed(RPM)I10זזזזזױן20304050607080100200400500- 600700800300100020003000- 40005000- 60007000800010000

Milling is the process of machining the surface of the object. Milling is done with the help of a…

From the speed chart below, determine the correct cutting speed for performing a facing cut on Brass with a milling machine using a 0.5 in. diameter ball-nose end-mill Surface Speed (Ft/Min) Aluminum Brass/Bronze Low Carbon Steel Cast Iron Alloy Steel 400 300 200 100 80 70 60 50 40 Diameter (in) NWA 10 0.6 0.3 0.2 0.1 Cutting Speed (RPM) 10 20 30 40 50 60 70 80 100 200 300 400 500 600 700 800 1000 2000 3000 4000 5000 6000 7000 8000 10000

From the speed chart below, determine the correct cutting speed for performing a facing cut on Brass with a milling machine using a 0.5 in. diameter ball-nose end-mill Surface Speed (Ft/Min) Aluminum Brass/Bronze Low Carbon Steel Cast Iron Alloy Steel 400 300 200 100 80 70 60 50 40 Diameter (in) NWA 10 0.6 0.3 0.2 0.1 Cutting Speed (RPM) 10 20 30 40 50 60 70 80 100 200 300 400 500 600 700 800 1000 2000 3000 4000 5000 6000 7000 8000 10000

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A student is using a lathe with 80-hp and 80% efficiency to fabricate a copper alloy with Sy = 1200ksi If the width of cut is 0.30 inand the student set a rake angle of 0and a cutting speed of 200fl / min while she assumed a coefficient of friction to be 0.5. What is the maximum depth of cut the student can achieve?
A turning operation is carried out on aluminum. Based on the specific energy values in the table in your text, determine material removal rate and cutting power in the operation under the following sets of conditions: (a) Cutting speed = 5.6 m/s, feed = 0.25 mm/rev, and depth of cut = 2.0 mm; and (b) cutting speed = 1.3 m/s, feed = 0.75 mm/rev, and depth of cut = 4.0 mm.
In a turning operation, cutting speed =200 m/min; feed = 0.25mm mm/rev, and depth of cut = 4.00mm Thermal diffusivity of the work material = 20m mm^2/s and volumetric specific heat =3.5(10^ -3 )J/mm^ 3 -C If the temperature increase above ambient temperature (20degreesC) is the angle measured by a tool-chip thermocouple to be 700degreesC, determine the specific energy for the work material in this operation.
Manufacturing Process In a turning operation on stainless steel with hardness = 200 HB, the cutting speed = 200m/min, feed = 0.25 mm/rev, and depth of cut =7.5 mm. Determine how much power will the lathe machine draw in performing this operation if its mechanical efficiency = 90 %. Use specific energy value is: U = 2.8 J/mm
An orthogonal cutting operation is being carried out under the following conditions: t0=0.38 mm, tc=0.65 mm, width of the cut= 2.5 mm, V=3.5 m/s, rake angle=6°, Fc= 515 N, and Ft=210 N. Calculate the percentage of the total energy that is dissipated in the shear plane.
22.29 Describe the necessary conditions for optimal utilization of the capabilities of diamond and cubic-boron-nitride cutting tools.
21.53 An orthogonal cutting operation is being carried out under the following conditions: to = 0.1 mm, tc = 0.2 mm, width of cut = 4 mm, V = 3 m/s, rake angle = 10°, Fc = 500 N, and Ft = 200 N. Calculate the percentage of the total energy that is dissipated in the shear plane.
2 1.60 For a turning operation using a ceramic cutting tool, if the speed is increased by 50% , by what factor must the feed rate be modified to obtain a constant tool life? Use n = 0.5 and y = 0.6.
A part to be turned in an engine lathe must have a surface finish of 1.6 μm. The part is made of a free machining aluminum alloy. Cutting speed = 150 m/min. The nose radius on the tool = 0.75 mm. Determine the feed that will achieve the specified surface finish.
A student is using a lathe with 80-hp and 80% efficiency to fabricate a copper alloy with Sy= 1200 ksi. If the width of cut is 0.30 in. and the student set a rake angle of 0° and a cutting speed of 200 ft/ min while she assumed a coefficient of friction to be 0.5. What is the maximum depth of cut the student can achieve?
2 1.46 Explain why the power requirements in cutting depend on the cutting force but not the thrust force.
A slab milling operation is performed on the top surface of a tool-steel workpiece 450 mm long by 7.5 cm wide. The helical milling cutter, which has an 80 mm diameter and seven teeth, is set up to overhang the width of the part on both sides. Cutting speed is 4000 mm/min, feed is 0.015 cm/tooth, and depth of cut = 0.60 cm. Determine (a) the actual machining time to make one pass across the surface and (b) the maximum metal removal rate during the cut. (c) If an additional approach distance of 0.05 m is added at the beginning of the pass, and an overtravel distance at the end of the pass equal to the cutter radius plus 0.0115 cm, what is the duration of the feed motion