i need the answer quickly QUESTION 2The C83400-red-brass rod AB and 2014-T6- aluminum rod BC are joined at the collar B and fixed connected at their ends If there is no load in themembers when T1 = 50'F, determine the average normal stress in each member when T2 = 120°F Also, how far will the collar be displaced? Thecross-sectional area of each member is 1.75 in?3 ft2 ft

Given T(1)=50 degree F T(2)=120 degree F Area cross-section =1.75 in(2)

The C83400-red-brass rod AB and 2014-T6- aluminum rod BC are joined at the collar B and fixed connected at their ends If there is no load in members when T1= 50'F, determine the average normal stress in each member when T2 = 120'F Also, how far will the collar be displaced? cross-sectional area of each member is 1.75 in B

The C83400-red-brass rod AB and 2014-T6- aluminum rod BC are joined at the collar B and fixed connected at their ends If there is no load in members when T1= 50'F, determine the average normal stress in each member when T2 = 120'F Also, how far will the collar be displaced? cross-sectional area of each member is 1.75 in B

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter11: Columns

Section: Chapter Questions

Problem 11.9.30P

See similar textbooks

Similar questions

The C83400-red-brass rod AB and 2014-T6- aluminum rod BC are joined at the collar B and fixed connected at their ends. If there is no load in the members when T1 = 50°F, determine the average normal stress in each member when T2 = 120°F. Also, how far will the collar be displaced? The cross-sectional area of each member is 1.75 in2.
The center post B of the assembly has an original length of 122 mm, whereas posts A and C have a length of 126 mm. If the caps on the top and bottom can be considered rigid, determine the average normal stress (in MPa) post A. The posts are made of aluminum and have a cross-sectional area of 403 mm2. Ealuminum = 70 GPa. The correct answer is 887.66682. Show solution pls.
A column has an outside diameter, D = 550 mm, an inner diameter, d = 150 mm.Determine the average normal stress developed on the cross section if the load, F is1890 kN.
The center post B of the assembly has an original length of 123 mm, whereas posts A and C have a length of 127 mm. If the caps on the top and bottom can be considered rigid, determine the average normal stress (in MPa) post A. The posts are made of aluminum and have a cross-sectional area of 423 mm2 Ealuminum = 70 GPa.
Pipe (2) is supported by a pin at bracket C and by tie rod (1). The structure supports a load P at pin B. Tie rod (1) has a diameter of 15 mm and an allowable normal stress of 115 MPa. Pipe (2) has an outside diameter of 58 mm, a wall thickness of 3 mm, and an allowable normal stress of 65 MPa. Assume x3 = 3.7 m, x2 = 1.5 m, and y; = 4.1 m, Determine the maximum load Pmax that can be supported by the structure without exceeding either allowable normal stress
The rigid beam is supported by the three suspender bars. Bars AB and EF are made of aluminum and bar CD is made of steel. If each bar has a cross-sectional area of 450 mm2, determine the maximum value of P if the allowable stress is (sallow)st = 200 MPa for the steel and (sallow)al = 150 MPa for the aluminum. Est = 200 GPa, Eal = 70 GPa.
Determine the load that can be applied at the end of the rigid bar if the stressin either spring shown in the figure shall not exceed 200MPa. Present detailed drawings/FBD’s illustrating your solution.
A stainless steel tube with an outside diameter of 50 mm and a wall thickness of 5 mm is used as a compression member. If the axial stress in the member must be limited to 384 MPa, determine the maximum load P that the member can support.
The 65 kg tag is supported by cables AB and BC, as shown in the image, which have diameters of 1.5 mm and 2 mm, respectively. If the cables have a normal ultimate stress of ?u = 400 ???. Determine: a) The safety factor in cable AB b) The safety factor in cable BC Please add the free body diagram.
If the allowable tensile stress for the bar is 1st2allow = 21 ksi, and the allowable shear stress for the pin is tallow = 12 ksi, determine the diameter of the pin so that the load P will be a maximum. What is this load? Assumethe hole in the bar has the same diameter d as the pin. Take t = 1 4 in. and w = 2 in.
The uniform 3000??bar is supported by a smooth wall at A and by a pin at B. Determine (a)the diameter of the smallest pin that can be used if not to exceed a shear stress of 60???(Drawthe required FBD and answer in mm)(b) the bearing stress in thesupport bracket (Draw the required FBD and answer in MPa)(c) the bearing stress in the bar at B (Draw the required FBD and answer in MPa).
The connection is made using a bolt and nut and two washers. If the allowable bearing stress of the washers on the boards is (sb)allow = 2 ksi, and the allowable tensile stress within the bolt shank S is (st)allow = 18 ksi, determine the maximum allowable tension in the bolt shank. The bolt shankhas a diameter of 0.31 in., and the washers have an outer diameter of 0.75 in. and inner diameter (hole) of 0.50 in.