The cantilever bracket Is bolted to a column with three M12 x 1.75 ISO 5.8 bolts. The bracket Is made from AISI 1020 hot-rolled steel. Assume the bolt threads do not extend into the Joint. Find the factors of safety for the following fallure modes:shear of bolts, bearing of bolts, bearing of bracket, and bending of the bracket. GIVE the overall jolnt factor of safety.Given: F= 2 KN.NOTE: This is a multi-part questlon. Once an answer Is submitted, you will be unable to return to this part.Holes for M12 x 1.75 bolts8 mm thick363236- 200-ColumnFind the factor of safety with respect to the shear stress In the bolts.The factor of safety with respect to the shear stress In the bolts ng Is4.4

Given data as per question Sy=420 Mpafor AISI 1020 heat rolled steelSy=210 Mpaconsidering FBD of…

The cantilever bracket is bolted to a column with three M12 x 1.75 ISO 5.8 bolts. The bracket is made from AISI 1020 hot- rolled steel. Assume the bolt threads do not extend into the Joint. Find the factors of safety for the following failure modes: shear of bolts, bearing of bolts, bearing of bracket, and bending of the bracket. Gve the overall joint factor of safety. Given: F= 2 kN. NOTE: This Is a multi-part question. Once an answer is submitted, you will be unable to return to this part. Holes for M12 × 1.75 bolts 8 mm thick 36 32 36 -200 Column

The cantilever bracket is bolted to a column with three M12 x 1.75 ISO 5.8 bolts. The bracket is made from AISI 1020 hot- rolled steel. Assume the bolt threads do not extend into the Joint. Find the factors of safety for the following failure modes: shear of bolts, bearing of bolts, bearing of bracket, and bending of the bracket. Gve the overall joint factor of safety. Given: F= 2 kN. NOTE: This Is a multi-part question. Once an answer is submitted, you will be unable to return to this part. Holes for M12 × 1.75 bolts 8 mm thick 36 32 36 -200 Column

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Determine the safe tensile load for fine series bolts of (a) M 24and (b) M 38. Assume that the bolts are not initially stressed and take the safe tensile stress as 450MPa.
A semi-elliptic spring used for automobile suspension, consists of two extra full-length leaves and eight graduated-length leaves, including the master leaf. The centre-to centre distance between the two eyes is 1 m. The leaves are made of steel 55Si2Mo90 (Syt = 1500 N/mm2and E = 207000 N/mm2) and the factor of safety is 2. The maximum spring load is 30 kN. The leaves are pre- stressed so as to equalize stresses in all leaves under maximum load. Determine the dimensions of the cross-section of the leaves and the deflection at the end of the spring.
A M20 × C4 bolt of mild steel is having yield stress of 320 MPa and factor of safety 3. The safe static tensile load in kN will be
Determine the safe tensile load for bolts of (a) M 17 and (b) M 26. Assume that the bolts are not initially stressed and take the safe tensile stress as 305 MPa
Determine the safe tensile load for bolts of (a)M 17and (b) M 26. Assume that the bolts are not initially stressed and take the safe tensile stress as 305MPa.
A rectangular bar is cut from an AISI 1018 cold-drawn steel flat. The bar is 1 in wide by 3/8 in thick and has a ¼ in-diameter hole drilled through the center. The bar is subjected to a tension load fluctuating between 800 and 3000 lb. estimate the factors of safety guarding against failure by yielding and by fatigue action. (Assume infinite life is desire)
Draw the Mohr Circle and mark important points for a rod under pure tensile load & torsion
An M30 × 3.5 ISO grade 8.8 bolt is used in a joint at a preload levelrecommended for reused connections, and the joint is subject to a repeated tensilefatigue load of P = 65 kN per bolt. The joint constant is C = 0.25.a) Determine the static load factors; b) The factor of safety guarding against a fatigue failure based on the Goodmanfatigue criterion
The rotating shaft running at n = 900 rpm, shown in the figure below, is machined from AISI 1045 CD steel. It is subjected to a force of F = 10.1 kN. The shaft is experiencing an operating temperature of 35 oC. With the specified loading and for the reliability of 99.9 %, Determine the minimum factor of safety for fatigue based on infinite life*. Determine the maximum safe load (Fmax) that can be applied for a factor of safety of 1.5 and a design life of 5x105 cycles, all other input values remaining the same. Determine the factor of safety against yielding.
A rigid coupling with 30 inches of bolt circle diameter transmits a torque of 18,000 lb-in. The coupling material has a yield strength of 90,000 psi. The coupling is fastened by six bolts. Assume design factor of N=3 Calculate the diameter of each bolt.
A right angled bell crank lever is to be designed to raise a load of 5 kN at the short arm end. The lengths of short and long arms are 100 and 450 mm respectively. The lever and the pins are made of steel 30C8 (S = 400 N/mm2). And the factor of safety is 5.the permissible bearing pressure on the pin is 10 N/mm². The lever has a rectangular cross section and the ratio of width to thickness is 3:1. The length to diameter ratio of the fulcrum pin is 1.25:1. Calculate (i) The diameter and length of the fulcrum pin (ii) The dimensions of the cross section.
Find the power required to drive a 1.5-in power screw having double square threads with a pitch of 1/4 in. The nut is to move at a velocity of 2 in/s and move a load of F = 2.2 kips. The frictional coefficients are 0.10 for the threads and 0.15 for the collar. The frictional diameter of the collar is 2.25 in.