A rigid coupling with 30 inches of bolt circle diameter transmits a torque of 18,000 lb-in. The coupling material has a yield strength of 90,000 psi. The coupling is fastened by six bolts. Assume design factor of N=3 Calculate the diameter of each bolt.

A rigid coupling with 30 inches of bolt circle diameter transmits a torque of 18,000 lb-in. The coupling material has a yield strength of 90,000 psi. The coupling is fastened by six bolts. Assume design factor of N=3 Calculate the diameter of each bolt.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter11: Columns

Section: Chapter Questions

Problem 11.2.4P: Repeat Problem 11.2-3 assuming that R= 10 kN · m/rad and L = 2 m.

See similar textbooks

Related questions

Q: Q1/ The power transmitted by the motor to the main shaft as shown in figure (1) are 15 kW with the…

A: A moment is a movement of the body when a body is rotating on an axis. The moment is also known as…

Q: Q1/ The power transmitted by the motor to the main shaft as shown in figure (1) are 15 kW with the…

A: Given, Power(P)= 15KWSpeed(N)=600rpmT1T2=3Material-SAE1040 carbon…

Q: 3. A flange compressive coupling is used to connect a driving electric motor to a reduction gear box…

Q: Example 6.2. A 45 mm diameter shaft is made of steel with a yield strength of 400 MPa. A parallel…

A: As per the given information, the diameter of the shaft is 45 mm, which is made of steel with a…

Q: QUESTION 7 Figure 7 shows an assembly consist of circular shaft AB, solid circular BC and a circular…

A: Torque diagram-

Q: Problem 4: A cast iron shaft, ASTM-25 with an ultimate tensile strength of 25,000 psi, is subjected…

Q: Q/A rigid type flange coupling are connected two shafts made of plain carbon steel. The shafts are…

A: Given Shear stress = 60 MPa Power, P = 25 kW Speed, N = 500 rpm Find Diameter, d

Q: Find the diameter of a solid steel shaft to transmit 18 kW at 990 r.p.m. The ultimate shear stress…

Q: The end plates of a high pressure boiler accumulator are fixed using a number of bolts of M16 × 2-…

A: Any action that can change the state of motion is called force. Force is described by its magnitude,…

Q: A shaft is required for a chain drive illustrated in figure 5.42. The power transmitted is 12 kW at…

A: Given:

Q: The figure shows a welded-arm. The arm is welded using ! normal yield strength of 393MPa. If the…

A: Given data: The given weld size from the figure is The radius of the weld is

Q: Properties of Angle Bar < 125 x 125 x 13 mm A = 3065 mm² x = 36.3 mm y = 36.3 mm Fy = 248 MPa , Fu =…

A: To Given that:M20 Bolt in standard holesA325 steel bolt,Properties of Angle Bar < 125 x 125 x 13…

Q: Design and draw a protective type of cast iron flange coupling for a steel shaft transmitting ‘P is…

Q: A 20° 20-tooth cast-iron spur pinion having a module of 4 mm drives a 32-tooth cast-iron gear. Find…

Q: Problem 4 The Figure shows a shaft simply supported in ball bearings at A and B, and is loaded by a…

Q: In the figure, bearings B and D from points A and E Tangential forces from the gears in the vertical…

A: Given: The tangential load in vertical direction, Fy = 2100 N The yield strength of material, Sy =…

Q: A solid square rod is cantilevered at one end. The rod is 0.6 m long and supports a completely…

A: Data given - AISI 1080 hot rolled steel Length = 0.6 m Load = 2KN Design factor = 1.5 N= 104

Q: Problem 3 A solid shaft is designed to transmit 60kW of power at a speed of 300 rpm. Knowing that…

Q: 4. A machine shaft turning at 600 rpm is supported on bearings 30" apart. Twenty HP is supplied to…

Q: 5 A rotating step shaft is loaded as shown, where the forces F, and FB are constant at 600 lbf and…

Q: Q1/ The power transmitted by the motor to the main shaft as shown in figure (1) are 15 kW with the…

A: Given dataPower transmitted by the motor to the main shaft P = 15kWSpeed of the motor N =…

Q: The figure shows a shaft mounted in bearings at A and D and having pulleys at B and C. The forces…

A: Given:- Shaft made up of AISI 1035 CD steel Shaft rotation speed = 1000 rpm Shaft diameter = 1.5 in…

Q: Design a hard steel (screw and nut) lubricated power screw for raising and lowering a load of 25 kN…

A: We have given power screw of square thread with a triple thread. D=major diameter = 40…

Q: Design and draw a neat sketch of a cast iron protective type flange coupling to transmit “P” kW at…

Q: Consider the belt drive having a diameter of 150 mm that is mounted on the overhung end of a shaft,…

A: Given: The diameter of belt drive, d' = 150 mm = 0.15 m The overhang length, x = 30 mm = 0.03 m The…

Q: Torsion Load 100 mm- Shafts ABC and DEF are made of A36steel. Shaft ABC is connected to an…

A: Given: The motor power, P = 2 kW The speed of shaft ABC, N = 62 rpm The factor of safety of shaft…

Q: Problem 1: The figure presented below shows a grooved rotating shaft with a ground surface finish…

Q: The figure shows a schematic drawing of a vehicular jack that is to be designed to support a maximum…

Q: Design and draw a neat sketch of a cast iron protective type flange coupling to transmit “P” kW at…

A: Given data: shear stress, τboit=τkey=40 MPa = 40 N/mm2 Crushing stress, σC=80 MPa=80 N/mm2…

Q: Torsion Load 100 mm- Shafts ABC and DEF are made of A36steel. Shaft ABC is connected to an…

A: Given: The motor power, P = 2 kW The speed of shaft ABC, N = 62 rpm The factor of safety of shaft…

Q: . Determine: the diameter of shaft

A: Given: P= 20 kW N=750 rpm T1/T2=2.5 WA=300 N WB=250 Nshear stress=70 MPa kt=2 km=1.5 DB=1000 mm…

Q: rotating shaft of 16 mm diameter is made of plain carbon steel. It is subjected to axial load of…

Q: 1. A jack having square threads of 50 mm nominal diameter and 10 mm pitch is supporting a load of 89…

Q: A flange coupling having six bolts on a pitch circle radius of 300 mm connects two hollow shafts…

Q: Pls give right answer with step by step explanation. Design a clamp coupling for a shaft diameter…

A: To design: The clamp coupling. Given: The shaft diameter is d=60 mm. The torsional moment is T=160…

Q: A motor is to transmit 150 kW to a piece of mechanical equipment. The power is transmitted through a…

Q: Two designs for a shaft are being considered. Both have an outside diameter of 50 mm and are 600 mm…

Q: Q1/ The power transmitted by the motor to the main shaft as shown in figure (1) are 15 kW with the…

A: Given : Power =15 kWSpeed ,n=600 rpmT1T2=3d=180 mm

Q: shaft transmits 75 kW power at 300 r.p.m. The distance between the two bearing is 3000 mm. It is…

A: Given that ,Power P=75kWspeed N=300 r.p.m Distance b/w bearing =300mm=3mshear stress for shaft…

Q: A flanged coupling rotating at 400 rpm have 4 steel bolts evenly tightened around a 100 mm bolt…

Q: . A jack having square threads of 50 mm nominal diameter and 10 mm pitch is supporting a load of 89…

Q: The end plates of a high pressure boiler accumulator are fixed using a number of bolts of M16 × 2 -…

A: Any action that can change the state of motion is force. Force is described by its magnitude, point…

Q: To transmit 20 kW at 1000 rpm with a service factor of 3, a rigid flange coupling should be…

A: Given that, Power transfer by coupling, P=20 kW,Speed of the coupling, N=1000 rpm,service factor,…

Q: A 16 in. diameter motor pulley is running at 600 rpm with a 6 in diameter shaft transmitting power…

A: Given data: diameter of pulley = D = 16 in = 0.4064 m Speed of pulley = 600 rpm diameter of shaft =…

Q: A transmission shaft supporting a helical gear B and an overhung bevel gear D is shown in Fig.…

Q: A flanged bolt coupling consists of eight 10 mm diameter steel bolts on a bolt circle 400 mm in…

Q: Q/ Figure below shows the load components acting on a helical gear mounted on a simply supported…

A: Permissible stress is stress which produces due to pressure or forces which does not exceed the…

Q: The shaft is shown in Figure 3 is modified using the shaft from Question 2. Manufacturer selected as…

A: Given dataForce F = 10kNRotation of the shaft N = 3000rpmPower P = 32kWTo determine the factor of…

Q: Two designs for a shaft are being considered. Both have an outside diameter of 70 m and are 900 mm…

A: outside diameter cannot be 70m when inside dater is 50 mm . hence, taking outside diameter as 70 mm…

Q: Q1/ The power transmitted by the motor to the main shaft as shown in figure (1) are 15 kW with the…

Concept explainers

Slope and Deflection

The slope in a deflected beam is described as an angle in radians made by the tangent of the section with the original axis of the beam. The deflection at any point on the axis of the beam is defined as the lateral displacement of the point before and after loading.

Question

Calculate the diameter of each bolt.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 3 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Design a rigid flange coupling to transmit a torque of 257N-m between two coaxial shafts. The shaft is made of alloy steel, flanges out of cast iron and bolts out of steel. Four bolts are used to couple the flanges. The shafts are keyed to the flange hub. The permissible stresses are given below: Shear stress on shaft =100MPa Bearing or crushing stress on shaft =250MPa Shear stress on keys =100MPa Bearing stress on keys = 250MPa Shearing stress on cast iron = 200Mpa Shear stress on bolts =100MPa Answer in Word please
Design a typical rigid flange coupling for connecting a motor and a centrifugal pump shafts. The coupling needs to transmit 15 KW at 1000 rpm. The allowable shear stresses of the shaft, key and bolt materials are 60 MPa, 50 MPa and 25 MPa respectively. The shear modulus of the shaft material may be taken as 84GPa. The angle of twist of the shaft should be limited to 1 degree in 20 times the shaft diameter. Note: show complete solution
Design a rigid flange coupling to transmit a torque of 250N-m between two coaxial shafts. The shaft is made of alloy steel, flanges out of cast iron and bolts out of steel. Four bolts are used to couple the flanges. The shafts are keyed to the flange hub. The permissible stresses are given below: Shear stress on shaft =100MPa Bearing or crushing stress on shaft =250MPa Shear stress on keys =100MPa Bearing stress on keys = 250MPa Shearing stress on cast iron = 200Mpa Shear stress on bolts =100MPa Torque = 257N-m
Two short shafts having identical diameters of 35 mm and rotating at 1000 rpm are connected by a flange coupling having five bolts with a 100 mm bolt circle. The design shearing stress of the bolt is 12 MPa and design compressive stress of the flange is 15 MPa. a. What is the power in kW transmitted by the short shaft? b. What is the torque transmitted by the shaft in lb-in? c. What diameter in mm of bolt should be used? d. How thick should the flange be in mm?
3. Design a compression coupling for a shaft to transmit 1300 N-m. The allowable shear stress for the shaft and key is 40 MPa and the number of bolts connecting the two halves are 4. The permissible tensile stress for the bolts material is 70 MPa. The coefficient of friction between the muff and the shaft surface may be taken as 0.3.
A mild steel shaft has to transmit 75 kW at 200 rpm. Design a cast Iron flange coupling for the shaft. The allowable stresses are Shear stress for the shaft and keys 40 N/mm²Shear stress for bolts = 28 N/mm²Shear stress for C.I. coupling = 20 N/mm² Take wearing stress as twice the shear stress value and number of bolts for coupling as 6.
Design a typical rigid flange coupling for connecting a motor and a centrifugal pump shafts. The coupling needs to transmit 15 KW at 1000 rpm. The allowable shear stresses of the shaft, key and bolt materials are 60 MPa, 50 MPa and 25 MPa respectively. The shear modulus of the shaft material may be taken as 84GPa. The angle of twist of the shaft should be limited to 1 degree in 20 times the shaft diameter. Note: show complete handwritten solution
What length of a square key is required for a 5-in diameter shaft transmitting 1000 hp at 1000 rpm? The allowable shear and compressive stresses in the key are 15 ksi and 30 ksi, respectively.
A 45 mm diameter shaft is made of steel with a yield strength of 400 MPa. A parallel key of size 14 mm wide and 9 mm thick made of steel with a yield of 340 MPa is to be used. Find the required length of key, if the shaft is loaded to transmit the maximum permissible torque. Use maximum shear stress theory and assume a factor of safety of 2.
7. Design a muff coupling for joining shafts transmitting 8 kW at 400 rpm. The shaft and the key are made of steel with 45 MPa and 80 MPa allowable stresses in shear and crushing, respectively. The material of the sleeve is CI, with allowable shear stress 10 MPa. Service factor KS =1.2.
5. Design a sleeve coupling for the transmission of 12 kW at 300 rpm by two connected steel shafts. Take service factor KS 1.25. The sleeve is made of CI. The key and the shaft are made of the same material. Allowable stress: Shear stresses in key and shaft 50 MPa Crushing stress in key= 100 MPa Shear stress in CI sleeve = 10 MPa
8. Design a clamp coupling for transmitting 25 kW at 300 rpm. Allowable shear stresses in shaft and key are 50 MPa and 45 MPa, respectively. The number of bolts joining the two halves of muff is 4. The permissible tensile stress in the bolt is 70 MPa and the permissible crushing stress in the key is 90 MPa. The coeffi cient of friction between the muff of the CI and the shaft of steel is 0.20.