The characteristic of the UJT exhibits the following values: n = 0.575, R81 = 10 k-ohms, Vv = 1.3 V, Iv =20mA, Ip=15UA. 25V B2 Determine the following: a. Determine the Rg2 (in kilo-ohms) of the UJT b. Determine the maximum value range of R (in kilo-ohms) that will ensure proper turn-on and turn-off of the UJT c. Determine the minimum value range of R (in kilo-ohms) that will ensure proper turn-on and turn-off of the UJT

The characteristic of the UJT exhibits the following values: n = 0.575, R81 = 10 k-ohms, Vv = 1.3 V, Iv =20mA, Ip=15UA. 25V B2 Determine the following: a. Determine the Rg2 (in kilo-ohms) of the UJT b. Determine the maximum value range of R (in kilo-ohms) that will ensure proper turn-on and turn-off of the UJT c. Determine the minimum value range of R (in kilo-ohms) that will ensure proper turn-on and turn-off of the UJT

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

For the transistor , IS = 4 × 10−16 μA,βF = 75, and βR = 4. (a) Label the collector, base,and emitter terminals of the transistor. (b) What isthe transistor type? (c) Label the emitter-base andcollector-base voltages, and label the normal direction for IE , IC, and IB. (d) Write the simplified formof the transport model equations that apply to thisparticular circuit configuration. Write an expressionfor IE /IB. Write an expression for IE /IC. (e) Findthe values of IE , IC, IB, VC B, and VE B.
In order to express the effect of the internal capacitors of BJT and the high frequency reception, the current gain expression depending on the frequency (Figure b) (hfe) is used in the case of collector emitter short circuit, voltage source connected at base end and emitter grounded (Figure la).. The catalog information of the 2N2222 transistor is given in Figure Ic. In the catalogue, when Ic=20 mA, it is seen as fT=250 MHz. a) Find the total capacitor effect for the case where gm> > wCμ. (Cpi) + (Cμ) = ?pF
For the transistor , IS = 6×10−16 μA,αF = 0.985, and αR = 0.25. (a) What type oftransistor is in this circuit? (b) Label the collector, base, and emitter terminals of the transistor.(c) Label the emitter-base and collector-base voltages, and label the normal direction for IE , IC, andIB. (d) Write the simplified form of the transportmodel equations that apply to this particular circuitconfiguration. Write an expression for IE /IC. Writean expression for IE /IB. (e) Find the values of IE ,IC, IB, βF , βR, VE B, and VC B.
Determine the VGS and VDS for the E-MOSFET circuit shown, with the parameters given on a datasheet I_D(ON)=500mA at V_GS=10V and V_GS(TH)=1V.
Suppose that we have an unusual type of FET for which iD=3 exp(vGS)+0.01vDS2 Here, iD is in mA, vGS is in volts, and vDS is in volts. Determine the values of gm and rd for a Q point of VGSQ=1 V and VDSQ = 10 V.
Problem: Fx=(AB+CD+EF+G)' a. Draw its equivalent transistor circuit. b. Determine if the function has an Euler's path. please draw the equivalent Euler's path. C. Whether the circuit has a Euler's path or not, draw the stick diagram.
A PMOS current mirror was designed with an IREF = 1mA. The carrier mobility and oxide capacitance are the same for both device but the (W/L) ratio of Mref = (10/1), while the (W/L) ratio of M1 = (5/1). Find the current ID1 assuming no channel modulation. Answer in mA with 2 decimal places. It was later found out that the value of ?=0.01 and VSD,REF = 0.4V and VSD1 = 0.3V . What is the new ID1 value? Answer in μA with 3 decimal places.
For an n-channel depletion-mode MOSFET, in the saturation region ID = 8mA when VGS = 0, and the dynamic (incremental) output resistance r0 is infinite. The threshold voltage (or pinch-off voltage) is VTR = VP = –2.5V. For VGS = 0, find the smallest value of VDS at which the MOSFET is in saturation. For VDS equal to this value, find ID when (i) VGS = –1V, (ii) VGS = –2V, (iii) VGS = –3V, (iv) VGS = –4V.
The switches as shown can be implemented using MOSFETs, as shown. What must be the W/L ratios of the transistors if the onresistance of the transistor is to be less than 1 percent of the resistor 2R = 12 kΩ? Use VREF = 3.0V. Assume that the voltage applied to the gate of the MOSFET is 5Vwhen b1 = 1 and 0Vwhen b1 = 0. For the MOSFET, VTN = 1 V, Kn = 50 μA/V2, 2φF = 0.6 V, and γ = 0.5√V.
IV (a) If R = 25 Kohm and C = 12 uF, find the frequency of the astable multivibrator using NAND gate? Draw the diagram and its output waveform for Vcc = + 15 V. (b) If C=9nF, the frequency F=72KHz of the Monostable multivibrator using NAND gate . Find the value of resistance ?
find the overall trasnfer function and range of k to make the system stable
Enclosed please find plot of my question for double linked transistors. For T1 transistor; hfe1 =120 , hie1 = 3.15kΩ and for T2 transistor hfe2=60 , hie2=1.2kΩ. For given values please find answers of below questions for small amplitude changes at low frequencies in circuit. a)Find the Voltage Gain (AV) ? b)Current Gain (AI) ?