The circuit shown below was used as a current source in a LED lighting application, and voltage quantities given below were measured for this circuit. Calculate the collector current, Ic ? Ien dınlntma aulama -nhidaki gerilım .ilmüstür .....ini anlavinız l-? Measurements: VRc = 1 V, VRb = 0.80 V, VBE = 0.65 V, VCE = 7.95 V, V2= 3.47 V Re VReS 100 V1 12 Rb B Q1 10k 2N3904 Re 100 O a. 5.00 mA O b. 10.00 mA O c. 2.50 mA O d. 2.00 mA O e. 3,33 mA

The circuit shown below was used as a current source in a LED lighting application, and voltage quantities given below were measured for this circuit. Calculate the collector current, Ic ? Ien dınlntma aulama -nhidaki gerilım .ilmüstür .....ini anlavinız l-? Measurements: VRc = 1 V, VRb = 0.80 V, VBE = 0.65 V, VCE = 7.95 V, V2= 3.47 V Re VReS 100 V1 12 Rb B Q1 10k 2N3904 Re 100 O a. 5.00 mA O b. 10.00 mA O c. 2.50 mA O d. 2.00 mA O e. 3,33 mA

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Topic: Direct Current Circuit which contains Open and Short Circuit, Series and Parallel Circuit, Current Divider Principle, Voltage Divider Prinicple, and Delta-Wyne Connection. Determine the value of VT and I. Note: DRAW THE DIAGRAM
Please give the step-by-step solution. Determine the following: (a) voc as seen at terminal a and b, (b) isc at terminals a and b, and (c) Norton euqivalent circuit as seen by terminals a and b
a) Explain the construction of LVDT. Identify some suitable examples according to their applications b) Discuss contacting and non-contacting tachometers Note question is taken from instrumentation and measurements course
A node in the circuit which is considered to hsve zero potential. A circuit analysus wherein the unknowns to be computed are voltages or potential differences. A circuit analysis wherein the unknowns to be computed are loop or mesh currents.
Using a circuit analysis technique of your choosing, calculate the mesh currents of the system atmidday, when the solar panel delivers its rated current.
Construct this circuit using the simulation: (simulation link: https://phet.colorado.edu/sims/html/circuit-construction-kit-dc/latest/circuit-construction-kit-dc_en.html ) Let: R1 = 2000 ohms R2 = 5000 ohms R3 = 3000 ohms R4 = 1000 ohms V1=24V 1. Total equivalent resistance of the circuit (using theoretical calculation) 2. Total current on the circuit (using simulation) 3. Total equivalent resistance of the circuit (using simulation) 4. % Error of #1 and #3 question.
(a) Determine IC and VCE for the circuit (a) given below.(b) Change β to 120 (50% increase), and determine the new values of IC and VCE for the circuit of Figure (a)(c) Determine the magnitude of the percent change in IC and VCE using the following equations:(d) Determine IC and VCE for the network of Figure (b).(e) Change β to 180 and determine the new value of IC and VCE for the network of Figure (b)(f) Determine the magnitude of the percent change in IC and VCE using the above equations. (g) In each of the above, the magnitude of β was increased 50%. Compare the percent change in IC and VCE for each configuration, and comment on which seems to be less sensitive to changes in β.
08. Consider a solar PV system with Number of PV modules: 4 The number of PV cells in one PV module: 28 Arca of cach PV cell= 134 cm (take insolation valuc as 1150 W/m and efficicncy as 15% ) For the connection schemes a &b, Calculate the following for the PV Panel: a) If the Four PV modules are connected in Scrics: a) Total output power b)Total output voltage c)Total output current
experiment (https://phet.colorado.edu/sims/html/circuit-construction-kit-dc-virtual-lab/latest/circuit-construction-kit-dc-virtual-lab_en.html):
Sketch the DC equivalent circuit Determine IDQ and VDSQ Determine VD and VS Show the details of your work Thanks!
Solve and show solutions. (Circuit Diagram Image below)
use these two images to answer all these questions: What are the differences between ac and dc meters? Can you compare the value of the current in the load resistance for the same value of voltage with ac and dc supply? What is the function of the autotransformer in this circuit? Can you use an autotransformer to obtain variable output voltage from a fixed dc supply? What will happen if dc meters are used instead of ac meters in this circuit? What the difference between resistance and impedance is when referred to dc and ac measurements?