The coefficient of static friction between the rope and the fixed post Dis μ = 0.18. The rope is wrapped only once around the post asshown in (Figure 1).Figure5 kNB< 1 of 1TPart ADetermine the minimum tension in the rope at point A which is necessary to maintain equilibrium.Express your answer to three significant figures and include the appropriate units.■μA?TA= 8.8KNSubmit Previous Answers Request AnswerX Incorrect; Try Again; 5 attempts remainingPart BDetermine the minimum tension in the rope at point B which is necessary to maintain equilibrium.Express your answer to three significant figures include appropriate units.μÀ?TB =ValueUnitsSubmitProvide FeedbackRequest Answer

Answered: Image /qna-images/answer/7b2110da-8e4b-4907-90e9-4a7487a2343b.jpg

The coefficient of static friction between the rope and the fixed post D is μ = 0.18. The rope is wrapped only once around the post as shown in (Figure 1). Figure 5 kN B ^ 1 of 1 T ▼ Part A Determine the minimum tension in the rope at point A which is necessary to maintain equilibrium. Express your answer to three significant figures and include the appropriate units. DA μA 3 ? TA= 8.8 KN Submit Previous Answers Request Answer X Incorrect; Try Again; 5 attempts remaining Part B Determine the minimum tension in the rope at point B which is necessary to maintain equilibrium. Express your answer to three significant figures and include the appropriate units. μÅ 3 ? TB = Value Units Submit Provide Feedback ▼ Request Answer

The coefficient of static friction between the rope and the fixed post D is μ = 0.18. The rope is wrapped only once around the post as shown in (Figure 1). Figure 5 kN B ^ 1 of 1 T ▼ Part A Determine the minimum tension in the rope at point A which is necessary to maintain equilibrium. Express your answer to three significant figures and include the appropriate units. DA μA 3 ? TA= 8.8 KN Submit Previous Answers Request Answer X Incorrect; Try Again; 5 attempts remaining Part B Determine the minimum tension in the rope at point B which is necessary to maintain equilibrium. Express your answer to three significant figures and include the appropriate units. μÅ 3 ? TB = Value Units Submit Provide Feedback ▼ Request Answer

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter7: Dry Friction

Section: Chapter Questions

Problem 7.75P: The single-plate clutch transmits the torque C from the input shaft on the left to the output shaft...

See similar textbooks

Similar questions

The homogenous 360 kg block rests against the vertical wall, for which the coefficiewnt of friction is 0.25. A force P is applied to the midpoint of the right face in the direction shown in thre figure. What range of values may P have without disturbing equilibrium. Give solution. (Ans. 5260 N < P < 7890 N)
The block brake consists of a pin-connected lever and friction block at B. The coefficient of static friction between the wheel and the lever is μs = 0.3, and a torque of 5 N ⋅m is applied to the wheel. Determine if the brake can hold the wheel stationary when the force applied to the lever is (a) P = 30 N, (b) P = 70 N Draw the free-body diagram of the lever.
A load G1 is placed on the horizontal plane. A rope is attached to it, which is passed over a stationary pulley, and a load of weight G2 is attached to the other end of the rope. Determine the equilibrium position of the load G1 (length x) if the height x and the coefficient of friction µ are known.Note: The answer is x=h\tan alpha i want to understdan how this problem is fixed.
A rope holding a 50 lb weight F passes over a pulley and is attached to a frame at A as is shown in Fig 9-34. The weight of C is 60 lb. What is the minimum coefficient of friction between the outer rope and the pulley for equilibrium? Give solutions. (Ans. coefficient of friction = 0.291)
A 150-lb block rests on a horizontal floor. The coefficient of friction between the block and the floor is 0.30. A pull of 40 lb, acting upward at an angle of 30° to the horizontal, is applied to the block. Determine whether or not the block will slide. - Draw Free-body diagram - Solve most simple way - use the formula Fmax= Ms (N)
Rod AB leans against the wall with a coefficient of static friction, μSB = 0.2. The contact surface at A is smooth (μSA = 0). Find the minimum force P necessary to prevent rod AB from sliding, given:WRod = 40 lbs, L1 = 7 ft, θ = 42 °.
Two blocks A and B, each having a mass of 7kg, are connected by the linkage shown in (Figure 1). If the coefficient of static friction at the contacting surfaces is Us = 0.5, determine the largest vertical force P that can be applied to pin C without causing the blocks to move. Neglect the weight of the links. Express your answer to three significant figures and include appropriate units.
A load weighing 10 kg is placed on a horizontal surface. A rope is attached to it, which is passed over a stationary pulley, and a load weighing 6 kg is attached to the other end of the rope. To determine the equilibrium position of the loads (length x) if the height h=0.5m and the coefficient of friction 0.3 are known.
The single-threaded screw of the vise has a mean diameter of 2 in. and has 5 square threads per inch. The coefficient of static friction in the threads is 0.20. A 60-lb pull applied normal to the handle at A produces a clamping force of 2,200 lb between the jaws of the vise. (a) Determine the tension T in the screw
An 800 N-m couple is applied to the flywheel asshown. The coefficient of belt friction is 0.20. Theminimum force P required to prevent rotation of theflywheel is applied.a.) Which Tension is larger, TA or TB? Explainb.) What is the angle of contact in radians?c.) What is the value of the ratio TA/TB? show fbd AND COMPLETE SOLUTION
load of Ft = 700 N comes to the free wheel of a car. The coefficient of friction between road and tire is µT = 0.8. Wheel radius is twice the disc friction radius (Rt = 2 Rs), µ = 0.35 between pad and disc and allowable pressure p = 0.5 N/mm2 Determine the pad sizes
An 800 N-m couple is applied to the flywheel as shown. The coefficient of belt friction is 0.20. The minimum force P required to prevent rotation of the flywheel is applied. a.) Which Tension is larger, Ta or Tb? Explain b.) What is the angle of contact in radians? c.) What is the value of the ratio Ta/Tb? Please answer these , with FBD and solutions please.