The y-component of the force F which a person exerts on the handle of the box wrench is known to be 44 lb. Determine the x- component and the magnitude of F. € Answers: Fx= F= i i lb lb

Q: int load of 5 KN at 3 Meters the following dimensions:

A: As per policy I will answer 1st question only

Q: Calculate the x- and y-components of the acceleration. Answers: mm/s² ax mm/s² ay" i

A:

Q: 1. Determine the pressure difference between the water pipe and the oil pipe.

A:

Q: A Carnot engine rejects 50% of the heat absorbed from a source to a sink at 27°C. What is the source…

A: Given data: TL=27°C=300 KQL=0.5QH Need to determine the source temperature.

Q: An aircraft has a wing area of 20 m² and whose wings resemble the NACA 23012 with no flaps and is…

A: Given data Wing type : NACA 23012 Wing Area = A = 20 m2 Speed of aircraft = 250 kmph = 69.4444 m/s…

Q: A 18-kg rear hatch of a vehicle opens as shown in the figure and can be modeled as a uniform 0.6-m…

A:

Q: 4. The Laplace transform 5 3²+4s+6 can be expressed as L{e¹[qssin(961) +9q7cos(** 1)]}

A:

Q: A jet issued of water at the rate of 200 L/s and a velocity of 36 m/s strikes a blade moving in the…

A: Given data Q=0.2 m3/sv=36 m/su=15 m/sδ=120° Here, Q is the flow rate, v is the velocity of jet and u…

Q: Wet saturated steam (x = 91.45%) at 16 bar (hf = 859 kJ/kg, hfg = 1935 kJ/kg) reducing valve is…

A: GIVEN DATA- AT 16 bar , hf=859KJ/kg , hfg=1935 KJ/Kg , x=91.45% AT 8 bar , hf =721 KJ/kg,…

Q: a force of magnitude pi is equals to 180 newtons is applied to the stationary machine handle as…

A:

Q: The number 8 is pointed to the 8 oil sump. O oil pump. O air inlet manifold. O water jackets. O 1G

A: The number 8 is pointed to cylinder head cover.

Q: Prob. # 3] The torsional deformation of a steel shaft is 1° in a length of 2 ft when the shearing…

A: Given data,  L= 2ft= 24in.  θ= 1°= 0.0174533 rad  S= 10000 psi  G= 12*10⁶ psi

Q: Use the method of sections to compute the force in members DF, EF, and EG of the cantilever truss…

A:

Q: The three components are as follows: u = 2xt– 3xyz + 6z v = x– yz + 4xyt w = 3x– 5yzt + yz Find…

A:

Q: Home Work: A cantilever shaft (d-20mm) is subjected to tensile load of (P-8 kN) and bending force of…

A: Find principal stress and maximum shear stress.

Q: With an angular velocity of = 2t2 rad/s rod AB rotates counterclockwise. Collar C moves along the…

A:

Q: Q2: Consider the steel spring in the illustration. (a) Find the pitch, solid height, and number of…

A: Dear student, we are suppose to solve only 3 sub parts. Please post other parts as a separate…

Q: Q1: The weldment shown in the figure is subjected to a force F. The hot-rolled steel bar has a…

A: we have to evaluate the maximum force to avoid failure

Q: A water tower supplies water through the plumbing in a house. A 3.50-cm-diameter faucet in the house…

A:

Q: A Rankine Cycle operates at a throttle pressure and temperature of 5 MPa and 450°C, respectively.…

A:

Q: Determine the maximum normal stress on a transverse plane in the straight portion of the structure…

A: To find: The maximum bending stress at the bottom for the both the symmetrical and non-symmetrical…

Q: In order to bore the tapered hole a straight hole must be drilled or bored. Find the size of the…

A:

Q: Q2: Consider the steel spring in the illustration. (a) Find the pitch, solid height, and number of…

A: Dear student, we are suppose to solve only 3 sub parts. Please post other question as a separate…

Q: Determine the moment of inertia ly (in.) of the shaded area about the y-axis. Given: x = 3 in. y = 5…

A:

Q: Which of the following tools is used in both marking and measuring? O Center Punch O Mallet O None…

A: Center punch is a marking tool used to mark center of a hole which is to be drilled. It is not a…

Q: A flywheel in the form of a uniform disk 4 ft in diameter weighs 600 lbs. What is its rotational…

A: Diameter of a disk, D=4 ftWeight of the disk, W=600 lbs

Q: A wood beam carries the loading shown in the figure. calculate the magnitude of the bending stress…

A:

Q: Question 4: Consider laminar flow through a very long straight section of round pipe. It is shown…

A:

Q: A car's roof has two tubes mounted to it. One tube is pointing to the other. The one in the front of…

A:

Q: 3. Determine the speed which the 630-kg four-man bobsled must have in order to negotiate the turn…

A:

Q: newly purchased sedan car operates on an ideal thermodynamic cycle. The engine has a compression…

A:

Q: The following diagram shows the basic structure of the gamma camera used for medical imaging to…

A: In nuclear medicine, the gamma camera, also known as a scintillation camera, is the most widely…

Q: 2. A test conducted on a four-stroke four-cylinder petrol engine having a bore of 75mm and a stroke…

A: (a) Mass flow rate of air consumption: Given that, Atmospheric condition in the test room are -…

Q: WA A 20° 90° B Wa

A:

Q: Using Double Integration Method, find: a) Equation of the Elastic Curve Slope at point C b) c)…

A:

Q: hy should i choice aluminum alloy over sintered bronze and cast bronze for camshaft bearing

A: Sintered bronze bearings are self-lubricating and require little maintenance. Sintered bronze…

Q: A jet issued of water at the rate of 200 L/s and a velocity of 36 m/s strikes a blade moving in the…

A:

Q: In a stamping operation, a 2 mm thick stainless steel sheet with an ultimate tensile strenght of 900…

A:

Q: Determine the exergy of 1 m³ of complete vacuum.

A: Given data as per the question volume =1 m3 Exergy Exergy is the available work of a system that can…

Q: A wood beam carries the loading shown in the figure. calculate the maximum bending stress (in Pa) if…

A:

Q: D. An open system with variable imaginary boundary E. Turbulent flow through a pipe with velocity…

A:

Q: P B **D*| W b D 2 ft T 2 ft| E

A: Calculated the shear force 6.16 ft to the right of point A for the beam.

Q: Determine the combined moment about O due to the weight of the mailbox and the cross member AB. The…

A:

Q: f a 2 mV signal produces a 2 V output, what is the voltage gain?

A: Given      Input voltage, v = 2 mV = 2 × 10-3 V  Output voltage, V = 2 V  Find Voltage gain, A

Q: A work group of 5 workers in a certain month produced 500 units of output working 8 hr/day for 22…

A: Given Dataunit=500day=22 day 8hrs/day worker =10unit=7200day=22 day8hr/day

Q: A car's roof has two tubes mounted to it. One tube is pointing to the other. The one in the front of…

A: Given data The manometer is filled with a liquid with specific gravity = 0.62 The height difference…

Q: 2. A test conducted on a four-stroke four-cylinder petrol engine having a bore of 75mm and a stroke…

A:

Q: A domestic refrigerator with inner dimensions of 0.7 m by 0.7 m at the base and height 1 m was…

A:

Q: Q2: Consider the steel spring in the illustration. (a) Find the pitch, solid height, and number of…

A: Dear student, we are suppose to solve only 3 sub parts. Please post other parts as a separate…

Q: An enormous and expensive artwork with mass 42.8 kg is mounted on a wall with four heavy-duty steel…

A: ◆ Shear stress in the bolts: Option (D): 5.35 × 106 N/m2 ◆ The resulting vertical deflection of the…