The compound bar, composed of the three segments shown, is initially stress-free. Compute the stress in each material if the temperature drops 25°C. Assume that the walls do not yield and use the following data:

The compound bar, composed of the three segments shown, is initially stress-free. Compute the stress in each material if the temperature drops 25°C. Assume that the walls do not yield and use the following data:

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: A constant wind blowing against the side of this chimney has caused creeping strains in the mortar…

A: Let us consider the height of the chimney is h and having constant cross-section against wind, the…

Q: A steel rod is subjected to a stress of 200 MPa and has Young's modulus of 200 GPa. Calculate…

Q: This open-ended silo contains granular material. It is constructed from wood slats and held together…

A: Consider the diagram shown below for the pressure distribution on the sidewall of the silo. The…

Q: Three equidistant vertical rods, each of 20 mm diameter, support a load of 25 kN in the same plane…

A: Given details:Es=205GPaEc=100GPadiameter of rod = 20mm

Q: A circular, metal rod of diameter 1 cm is loaded in tension. When the tensile load is 5kN, the…

Q: A stress-strain diagram for a tension test of an alloy steel sample is shown in the diagram below.…

A: Stress-Strain curve describes the relationship between stress and strain under a certain load in…

Q: A load of 20 kN is applied to a rod with a diameter of 12.5 mm. Calculate the strain in the rod if…

A: Given Data: The load applied, P=20 kN Diameter of the rod, d=12.5 mm Young's modulus, E=103 GPa

Q: between a ductile and brittle material and the concept of ductility and its measurement. b)A…

Q: The steel bolt and anchor assembly is used to reinforce the roof of a passageway in an underground…

Q: (a) Determine the indentation diagonal length when a load of 0.60 kg produces a Vickers HV of 400.…

Q: Compute the maximum length of the specimen before deformation if the

Q: 1. Label all points of significance on the stress strain curve 2. Draw the stress-strain curve for…

A: **According to the guidelines we can answer only three sub parts of a question, please resubmit the…

Q: The data shown in the accompanying table are From a tensile test of high-strength steel. The test…

Q: A 25 mm diameter bar is subjected to an axial tensile load of 100KN. Under the action of this load a…

A: Since you have posted multiple independent questions we will solve the first question for you To get…

Q: When a thin cylinder is subjected to an internal pressure p, the tangential stress should be the…

A: When a thin cylinder is subjected under the internal pressure, the stress will be distributed over…

Q: 9-b) A circular bar is 0.200 m long and 25 mm diameter. It carries a load of 50 KN. Given that…

Q: 2.76 Steel railroad rails 10 m long are laid with end-to-end clearance of 3 mm at a temperature of…

Q: A 0.5-m-long rod of annealed 410 stainless steel was loaded to failure in tension. The rod…

A: Before necking, the maximum stress and total elongation at failure is taken from the table of…

Q: A bolt weighing 2 kg is accidentally dropped down a vertical cast-iron pipe 4 m long. The lower end…

Q: The compound bar, composed ot the three segments shown, is initially stress-free. Compute the stress…

A: Given data as per the question Length of aluminium rod =800 mm Length of bronze rod = 500 mm Length…

Q: You are in charge of designing a new fixture for a “universal testing machine” that will attach a…

A: The data given is, Maximum load = 30 kN Maximum permissible shear stress, σ = 600 Mpa To…

Q: A steel Bar is Ø12mm and 2m long is stretched with a force of 35KN and extends by 0.05mm. Calculate…

A: Given Data Diameter = 12 mm Length =2 m Load = 35 KN ∆l=0.05 mm=5×10-5 m

Q: 200 stress (MPa) 150 100 50 0.1 0-2 strain From the tensile stress-strain behavior for the brass…

Q: Natural rubber is tested in tension to a maximum extension ratio of λ = 3. The Mooney-Rivlin…

A: maximum extension ratio of λ = 3. The Mooney-Rivlin constants C1 =…

Q: (a) One end of a wire of length L and diameter d is attached to a high ceiling. The wire hangs…

A: The mathematical expression to calculate the stress produced in the wire due to its self-weight is…

Q: The stainless steel specimen is shown in Figure 3 with tensile engineering stress-strain behaviour.…

Q: A cylindrical pressure vessel is made by shrinking a brass shell over a mild steel shell. Both…

A: Given Data The wall thickness is:hwall=6 mm The external diameter of the brass tube is:De=750 mm…

Q: A 3.048 m annealed rod with a cross-sectional area of 555 mm2 was extruded from a 5083-0 aluminum…

A: Given: The initial length of rod, Li = 3.048 m The final length of the rod, Lf = 3.0518 m The…

Q: e the magnitude of the load necessary to produce an elongation of 2.22mm. b) What will be the…

A: solution of above question below

Q: when the applied tensile stress is 150 MPa , and the affected force is 7540 N, find the .diameter of…

A: Write the formula for tensile stress on the specimen with a circular cross-section in terms of the…

Q: Three equidistant vertical rods, each of 20 mm diameter, support a load of 25 kN in the same plane…

A: Given data: As the diameter of each rod is the same, so the cross-section area will be also the…

Q: A hollow cylinder 2 m long has an outside diameter of 50 mm and inside diameter of 30 mm. If the…

A: According to Hooke's Law, Stress is directly proportional to the strain up to a certain point. After…

Q: A bar of triangular cross section with base 15mm carries a load of 100 kN. Calculate its minimum…

Q: What temperature will the rails just touched if steel railroad is 10 m long are laid with clearance…

Q: A rod is subjected to a uniaxial load within linear elastic limit. When the change in the stress is…

A: Given data: The change in stress, σ=200 MPa. The change in strain, ε=0.001. The Poisson's ratio,…

Q: A steel bolt 8mm diameter fits loosely inside aluminium tube 8mm diameter and 16 mm outside diameter…

A: Diameter of steel rod=8 mmInside dia. of Aluminium tube=8mmOuter dia. of Aluminium…

Q: A double riveted lap joint is made between 15mm thick plates. The rivet diameter and pitch are 25 mm…

Q: An aluminum wire of length 2.0 m and diameter 5 mm is used to hang a load of 100 kg. The modulus of…

Q: The yield stress for mild steel is 207MP.. A specimen with diameter of 0.01lm and length of 0.1m is…

Q: 40-mm sides glass polymer fibers composite cube is shown in Figure.1. The Glass polymer fibers…

Q: A 3-mm-long gold alloy wire intended to electricallybond a computer chip to its package has an…

A: Given data: The initial length of wire, Li = 3 mm. The initial diameter, di = 30 μm. The final…

Q: A cylindrical shape 25.0 mm in diameter and 21.0 mm in height is cut from a pear. Using an Instron…

Q: From the tensile stress-strain behavior for the brass specimen ,P the diamcter is 12-8 mm Calculate…

Concept explainers

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.

Question

The compound bar, composed of the three segments shown, is initially stress-free. Compute the stress in each
material if the temperature drops 25°C. Assume that the walls do not yield and use the following data:

A (mm?)
a (PC)
E (GPa)
Bronze segment
2000
19.0 x 10-6
83
Aluminum segment
1400
23.0 x 10-6
70
Steel segment
800
11.7 x 10-6
200
-500 mm-400 mm-
800 mm
Aluminum
Steel
Bronze

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Lo=80 mm, Copper Alloy C93200 (bearing bronze), T1=20 C, T2=75 C. dL=?, Lf=? Copper Alloy C93200 (bearing bronze) is Coefficient of Thermal Expansion : 10-6 (°C)-1 is 18.0 Coefficient of Thermal Expansion : 10-6 (°F)-1 is 10.0
Given:aluminum pm=0.0027g/mm³ E1m=E2m=70Gpa Graphite p1=0.0018g/mm³ E1f=220Gpa E2f=20Gpa
L=800mm, b=25mm, w0=300kN/m, σall=200 MPa
Answer item 1 only Diameter 100.5mm thickness 10.25 mm axial stree 451 mpa
a. how will you calculate the value of the slope of this best-fit line? b. How will the value of the slope help you identify the unknown material that the cylinders are made of?
20- Vickers Hardness Number (HV) value is directly proportional to a. Shape of indenter b. Indentation mean diagonal c. All of the above d. Force applied
Process used to improve fatigue resistance of the metal by setting up compressive stresses in its surface is known as: A. Extrusion B. Pircing C. Cold peening D. Up Setting
EGMN 202 Deformables, question is attached.
_________ generally represents the total change in dimension experienced by the member. -elasticity -stress -deformation -strain
4 In hardness test, a force of 3000 kgf applied using steel ball of 10 mm, the result hardness value is (BHN=200+N) where N is your number in class. Calculate the mean depression w bli nöy :diameters (d)? N=92
An aluminum rod is to withstand an applied force of 45,000 pounds. To assure sufficient safety, the maximum allowable stress on the rod is limited to 25,000 psi. The rod must be at least 150 in. long but must deform elastically no more than 0.25 in. when the force is applied. Design an appropriate rod.
Define the term Stress Concentrations?