9-b) A circular bar is 0.200 m long and 25 mm diameter. It carries a load of 50 KN. Given that          the modulus of elasticity is 150 MPa, calculate the tensile stress, strain and determine         how much length of the rod is increased

Q: A thin cylindrical pipe with an inside diameter of 300 mm is 6 mm thick and fitted with end covers.…

A:

Q: ort square is 1 1/2 inches x 1 1/2 inches in cross section. it is on an axial tensile load of 11,000…

A:

Q: Three equidistant vertical rods, each of 20 mm diameter, support a load of 25 kN in the same plane…

A: Given details:Es=205GPaEc=100GPadiameter of rod = 20mm

Q: 1. A bar is subjected to a tensile stress of 100 MPa, Determine the normal and tangential stresses…

A: Givenσ=100Mpaθ=30o

Q: 1.25 The piece of wood, 100 mm by 100 mm in cross section, contains a glued joint inclined at the…

A: Given data: The area of a cross section of wood, A = 100 mm by 100 mm. The stress for tension, σt =…

Q: A reinforced concrete column 200 mm in diameter is designed to carry an axial compressive load of…

A:

Q: Do larger members fail at comparatively lower stresses than smaller members?

A: When a moment or couple is acting over the member, then the size of the member is a matter of…

Q: 4. A ring made of 2-5 cm diameter steel bar carries a pull of 10 kN. Calculate the maximum tensile…

A: Given: The diameter of ring, d = 2.5 cm 0.025 m The load, P = 10 kN The mean radius, R = 15 cm =…

Q: In Figure 1, with its dimensions, loading status and material properties, different full circle…

A: Given data: The diameter of part AB is dAB=100 mm The diameter of part BC is dBC=80 mm The length of…

Q: 13.9 (8) A thick cylinder has an internal diameter of 75 mm and an external diameter of 125 mm. The…

A:

Q: A cantilever beam, 100 mm wide by 270 mm high and 9 m long, carries a load that varies uniformly…

A: Given:b=100 mmd=270 mmL=9 mW=1300 N/m

Q: 1. A BRONZE ROD IS SUBJECTED TO A TENSILE LOAD OF 15,000N. IF ITS ALLOWABLE STRESS IS 75 MPa,…

A: GivenP=15000NLi=40mmLo=L=?σallow=75MPa=75 N/mm2

Q: Two square bars (15mm thick) are bolted together as shown. Volt's allowable shear stress is 90 MPa,…

A:

Q: 1. A reciprocating steam engine connecting rod is subjected to a maximum load of 65 kN. Find the…

A: Question (1) is Solved here.  For Other Question, Please  Post this Question.

Q: 1. Given that the length of the sample is 90 mm and the diameter of it is 7 mm. i. Draw the stress…

A: Write the expression of stress. Write the expression of strain. Draw the given table and calculate…

Q: 04: A cross-sectioned rod (5*5cm) was subjected to a compressino force (F=500*10³ N), so the…

A:

Q: A 5-m high aluminum cylinder must support a load of 450 kN. If the maximum allowable stress is 0.14…

A: Stress:  When a component or a part is subjected to any external force, a resisting force will be…

Q: gure t shows a compound bar with three different diameters, d1-9mm, d2-22mm, and d3-14mm machined…

A: Given Data: The diameter of section 1 is, d1=9 mm. The diameter of section 2 is, d2=22 mm. The…

Q: QUESTION 3: A steel rope with a diameter of 1 cm is subjected to a tensile load of "120" N.…

A: Given data: Diameter of rope, d=1 cm= 10mm Tensile load on the rope (along the axis), P=120N.

Q: 4- Draw Shear Stress-strain diagram for Cast Iron

A:

Q: Three equidistant vertical rods, each of 20 mm diameter, support a load of 25 kN in the same plane…

A: Given data: As the diameter of each rod is the same, so the cross-section area will be also the…

Q: A thin walled spherical shell is subjected to an internal pressure. If the radius of the shell is…

A: The formula for the hoop stress can be expressed as,

Q: Taking the safety factor as 2 for the loading condition shown in the figure, we can calculate the…

A: Given: d=100mm Syt = 250 MN / m2 Sys = 140 MN / m2  E = 200 GPa μ=0.3 N = 2

Q: (i) Calculate the normal stress o on the upper part of the post. (ii) If it is desired that the…

A:

Q: Question 5 required to raise the load if the yield stress of steel is 300MPA. A lead of 5kN is to be…

A:

Q: must give units) a) Yield strength,Tensile/Ultimate strength,Modulus of

A: Given data Dia of specimen = 12.5 mm Gauge length = 50 mm Poisson's ratio = .33 Required Yield…

Q: Question Two A steel flat of thickness 10 mm tapers uniformly from 60 mm at one end to 40 mm at…

A:

Q: A reinforced concrete column 200 mm in diameter is designed to carry an axial compressive load of…

A:

Q: The compound bar, composed of the three segments shown, is initially stress-free. Compute the stress…

A: Solution -> Given that there is no yielding in the walls.                → Net change in length…

Q: 10.8 (B). A compound cylinder is formed by shrinking a tube of 200 mm outside and 150 mm inside…

A: To Find : The magnitude and the position of the maximum hoop stress . Given :  The outside diameter…

Q: A cantilever beam, 80 mm wide by 260 mm high and 9 m long, carries a load that varies uniformly from…

A: Width of the cantilever beam, B= 80 mm Height of the cantilever beam, H= 260 mm Length, L= 9 m At…

Q: Problem (1): The rigid, horizontal slab is attached to two identical copper rods. There is a gap A…

A:

Q: Answer the attach file

A: We are authorized to answer one question at a time, since you have not mentioned which question you…

Q: A 1 Mg container hangs from a 16 mm diameter steel cable. What is the stress in the cable? (Express…

A: It is the case of stress developed due to axial loading. Tensile stress=axial force/cross section…

Q: Q15: Using the stress-strain diagram for the stainless steel bar shown in the problem statement,…

A: In this problem, it is asking about the modulus of elasticity of stainless steel bar. Consider the…

Q: An aluminum wire of length 2.0 m and diameter 5 mm is used to hang a load of 100 kg. The modulus of…

A:

Q: n Figure 1, with its dimensions, loading status and material properties, different full circle…

A: Given data

Q: Question Two A steel flat of thickness 10 mm tapers uniformly from 60 mm at one end to 40 mm at…

A: “Since you have asked multiple questions, we will solve the one question for you. If you want any…

Q: A cantilever beam, 90 mm wide by 240 mm high and 7 m long, carries a load that varies uniformly from…

A: Answer: The magnitude of the stress at the given point of consideration is 1.72233 MPa.

Q: Q1: As shown in Fig. 1, there is a gap between the aluminum bar and the rigid slab that is supported…

A: Dear student as you have posted multiple Question , as per the policy i can answer only one question…

Q: Question 3 (a) One end of a wire of length L and diameter d is attached to a high ceiling. The wire…

A:

Q: Q1 A round bar is subjected to a rotating force. State what type of stress is induced in the bar and…

A:

Q: A rod is hanging vertically, supports a load of 2000N. Neglecting the weight of the wire, determine…

A: Given data,  P= 2000 N  Tensile stress = σ= 140 MPa, N/mm2

Q: A cantilever beam, 80 mm wide by 220 mm high and 8 m long, carries a load that varies uniformly from…

A: Find the normal stress in a fiber 70 mm from the top of the beam at a section 5 m from the free end.

Q: Six steel cables support a circular moulding of diameter 2m. The cables are spaced equally along the…

A: