The concrete post (Ec = 3.6 × 106 psi and αc = 5.5 × 10-6/°F) is reinforced with six steel bars, each of 78-in.78-in. diameter (Es = 29 × 106 psi and αs = 6.5 × 10-6/°F). Determine the normal stresses induced in the steel and in the concrete by a temperature rise of 75°F.

The concrete post (Ec = 3.6 × 106 psi and αc = 5.5 × 10-6/°F) is reinforced with six steel bars, each of 78-in.78-in. diameter (Es = 29 × 106 psi and αs = 6.5 × 10-6/°F). Determine the normal stresses induced in the steel and in the concrete by a temperature rise of 75°F.

Refrigeration and Air Conditioning Technology (MindTap Course List)

8th Edition

ISBN:9781305578296

Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Publisher:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Chapter2: Matter And Energy

Section: Chapter Questions

Problem 12RQ: The specific volume of red brass is 0.001865 ft3/lb. Whatwould be its density?

See similar textbooks

Related questions

Q: Determine pressure in [kPa] in the cylindrical pressure vessel shown, if the measured hoop strain is…

A: Given, εhoop=500×10-6E=70 GPa=70×109 Paμ=0.33Ri=400 mm=400×10-3 mmt=6 mm=6×10-3 mm Internal diameter…

Q: For a thin-walled cylindrical pressure vessel with hemispherical end caps, constructed of uniform…

Q: 8. The Howe truss is loaded by three concentrated forces. The rivet connection at joint B is shown…

Q: The five-bolt connection must support an applied load of P = 1500 lb. If the average shear stress in…

Q: A stainless-steel thick-walled cylinder with inner and outer radii (b and a) of 225 mm and 350 mm,…

Q: When the temperature is 10°C, the two rods are separated by a 0.5-mm 0.5 mm gap as shown. If the…

Q: The long bolt passes through the 30-mm-thick plate. If the force in the bolt shank is 10 kN,…

A: Given: P = 8 kN the normal stress and shear stress are calculated for mentioned plane using formula.

Q: A spherical gas tank has an inner radius of r = 1.5 m. If it is subjected to an internal pressure of…

A: Given: The internal pressure in the tank is p=300 kPa. The inner radius of the spherical tank is ri…

Q: The spherical gas tank is fabricated by bolting together two hemispherical thin shells of thickness…

Q: Determine the normal stress in a ball, which has an outside diameter of 185 mm and a wall thickness…

A: Outside ball diameter, do=185 mmThe wall thickness of the ball, t=3.1 mmA gage pressure inside the…

Q: The prismatic bar has a cross-sectional area A. If it is subjected to a distributed axial loading…

A: Represent linearly varying load on diagram Take a section at x from left and load can be calculated…

Q: The assembly consists of a solid 15 mm diameter rod connected to the inside of a tube using a rigid…

Q: Determine the shear force acting at each of the following locations: (a) x = 0+ ft (i.e., just to…

Q: When filled to capacity, the unpressurized storage tank contains water to a height of h = 49 ft. The…

A: To find: The maximum normal stress and maximum shear stress. Given: The height of water in the tank…

Q: The bar has a cross-sectional area of 480(109 m². It is subjected to a triangular axial distributed…

A: Area of the cross section A=480 ×10-6 m2 Horizontal reaction at fixed end R R=12×9×1.5+8+4=18.75 kN…

Q: When filled to capacity, the unpressurized storage tank contains water to a height of h = 27 ft. The…

A: Givenh=27ftd=8.2ftt=0.861 in =0.07175 ftγ=62.4/ft3

Q: Determine the normal stress in a ball, which has an outside diameter of 180 mm and a wall thickness…

A: As per given question Gage pressure =66mpa Wall thickness =4.6 mm Outside diameter =180 mm We have…

Q: The long bolt passes through the 30-mm-thick plate. If the force in the bolt shank is 10 kN,…

Q: A spherical gas tank has an inner radius of r = 1.5 m. If it is subjected to an internal pressure of…

A: Step-1 Given: The inner radius of the spherical tank is r=1.5 m. The internal pressure of the…

Q: Determine the shear stress in a hollow circular cross-section with an outside diameter of 100mm and…

Q: A pipe made of wood staves is 150 mm internal diameter and subjected to internal pressure of 1 MPa .…

Q: a) The built-up shaft consists of a pipe AB and solid rod BC. The pipe has an inner diameter of 20…

A: Given, di = 20 mm do = 28 mm D = 12 mm

Q: Determine the maximum normal stress in the bar. The diameter is 1.5cm. F1 = 7KN F2 = 6KN F3 =…

Q: The resulting stress distribution along section AB for the bar is shown. From this distribution,…

Q: e inner diameter of the AB compressed air tank is 160mm, the wall thickness is 1mm.Since the…

Q: The pressure in the tank is 2800 kPa, and an axial load of 130 kN is applied to the end of the tank…

Q: An oil pipeline is made from steel with a diameter of 50 cm and a thickness of 7 mm. If the oil is…

A: Given:- D=50 cm t=7mm P=8 MPa FOS=1.5 To find:- Maximum allowable stress,σ

Q: The cylindrical pressure vessel has an inner radius of 1.25 m and a wall thickness of 15 mm. It is…

A: According to the given condition We have the stress along its longitude as…

Q: The five-bolt connection must support an applied load of P = 4600 lb. If the average shear stress in…

Q: The thin-walled pipe has an inner diameter of 0.5 in. and a thickness of 0.025 in. If it is…

A: Given: The thickness of the wall is t=0.025 in. The inner diameter of the wall is d=0.5 in. The…

Q: A pressure-vessel head is fabricated by welding the circular plate to the end of the vessel as…

A: Average shear stress can be determined by using equilibrium condition in y direction

Q: A steel gear, with 80-mm diameter rod connected to it is used to transmit 600 HP at 200 rpm. If the…

A: Given: d = 80 mm H = 600 hp n = 200 rpm

Q: The steel pipe of length L = 541 mm is filled with concrete and subjected to a compressive force P =…

Q: A steel cable having a diameter of 0.4 in. wraps over a drum and is used to lower an elevator having…

A: Load developed(P) in the cable is given by:→P=∆L×AELwhere∆L=extension/deformation in cableL=Length…

Q: The spherical gas tank is fabricated by bolting together two hemispherical thin shells of thickness…

A: Given t=30mm P=2.5MPa D=8m=8000mm n=900 d=20mm

Q: Determine the maximum force that can be applied such that the maximum stress does not exceeds 210…

Q: The bar has a cross-sectional area of 400(10−6) m2. If it is subjected to a uniform axial…

A: For the F.B.D of the shaft. For the equilibrium of the shaft in horizontal direction.

Q: The thin-walled pipe has an inner diameter of 1.2 cm and a thickness of 0.06 cm. If it is subjected…

A: Determine the axial and hoop tension as follows.

Q: Determine the change in the volume of a 10 cm diameter copper sphere that is subjected to a…

Q: Determine the principal stresses, the maximum in-plane shear stress, and average normal stress.…

A: Given: The normal stress in the x-direction is бx=30 MPa The normal stress in the y-direction is…

Q: A steel cable having a diameter of 0.4 in. wraps over a drum and is used to lower an elevator having…

A: Given Data Dia of the cable, 0.4in Weight of the elevator, 800 lb Young modlus of elasticity, E =…

Q: The pipe assembly shown is subjected to a forde F = 12 kN and P = 6 kN. It is made of steel with Sy…

A: Given:F=12 KNP=6 KNSy=250 MPad=176 mmD=200 mmThe force P will generate a bending moment at Point…

Q: Q2: Determine the state of stresses at point A on the cross section of the pipe shown in Fig. D=50mm…

Q: A steel cable having a diameter of 0.4 in. wraps over a drum and is used to lower an elevator having…

A: Given Data The diameter of the steel cable is: d=0.4 in Weight of the elevator is: W=80 lb The…

Q: A pressure vessel containing gas at 250 psi has an outer diameter of 12 inches and a thickness of…

Q: A paper tube is formed by rolling a paper strip in a spiral and then gluing the edges together as…

Question

The concrete post (E_c = 3.6 × 10⁶ psi and α_c = 5.5 × 10^-6/°F) is reinforced with six steel bars, each of 78-in.78-in. diameter (E_s = 29 × 10⁶ psi and α_s = 6.5 × 10^-6/°F).

Determine the normal stresses induced in the steel and in the concrete by a temperature rise of 75°F.