The contact angle for water in a clean glass is zero. Calculate the surface tension of water in a 0.3 mm diameter vertical tube if the water rises to a height 4.96 cm above the liquid outside the tube, knowing that specific gravity of water equals 998.2 kg/m 3 and the acceleration due to gravity equals 9.806 m/sec2

The contact angle for water in a clean glass is zero. Calculate the surface tension of water in a 0.3 mm diameter vertical tube if the water rises to a height 4.96 cm above the liquid outside the tube, knowing that specific gravity of water equals 998.2 kg/m 3 and the acceleration due to gravity equals 9.806 m/sec2

Name: ChemistryThe contact angle for water in a clean glass is zero. Calcula
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: ChemistryThe contact angle for water in a clean glass is zero. Calculate the surface tension of waterin a 0.3 mm diameter vertical tube if the water rises to a height 4.96 cm above the liquidoutside the tube, knowing that specific gravity of water eq

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter8: Centroids And Distributed Loads

Section: Chapter Questions

Problem 8.122P: The 12-ft wide quarter-circular gate AB is hinged at A. Determine the contact force between the gate...

See similar textbooks

Similar questions

The flow of water from a reservoir is controlled by an L-shaped gate hinged at point A, as shown in the figure. The mass of the weight at B (a = 4 m to the right of A, b = 3 m above the base) is 5125 kg. If the gate opens when the water height is 1.75 m above the base, determine the width (in meters, not showing) of the gate.
For the tank of water shown below, the radius of the circular surface is R=1.0 m, h=1.0m, and the length of the tank is w=2.0 m. Determine (1) the correct expression of the area magnitude whose volume weight is equivalent to the vertical force exerted on the whole curved surfaces_________
U - tube is used to pressure the difference in water channel. p1= 1000 kg/m3. The orange fluid in the U - tube has a density: p2= 2000 kg/m3. The height a = 10 cm and h = 15 cm. If the pressure at point ① is 111 kPa, what is the pressure at point ② ?
In the hydraulic jack shown, a force of 100 N is exerted on the small piston. Determine the upward force on the large piston. The area of the small piston is 65 cm2, and the area of the large piston is 950 cm2. If the small piston moves 12 cm, how far will the large move? Assume the oil to be incompressible.
Open tank (4.5 m long, 2.5 m height and 3 m wide) contains liquid (S-0.75) to height 1. m. If this tank is accelerated along its length on a horizontal truck at a constant value of 3.5 m/s, determine pressure at the bottom of the tank at front and rear edges (in kN/m). (take y=9.8 kN/m for water)
he gage pressure of the air in the tank shown in the figure is measured to be 65 kPa. Determine the differential height h of the mercury column.
For the tank of water shown below, the radius of the circular surface is R=1.0 m, h=1.0m, and the length of the tank is w=2.0 m. Determine (3) the magnitude of the vertical force force exerted on the whole curved surfaces_________kN
A closed tank rectangular in plane with vertical sides is 1.8m deep and contains water to a depth of 1.2m. Air is pumped into the space above the water until the air pressure is 35kN/m2. If the length of one wall of the tank is 3m, determine the resultant force on this wall and the height of the centre of pressure above the base
How long will it take the water surface in the tank shown to drop from h = 3 m to h = 50 cm?
Derive a formula for capillary rise (h) between two concentric glass tubes of radiuses RI and R2. determine its value for water if (G. = 0.072 N/m, RI=30mm, & R2=36mm) (Take smooth and very clean glass tubes).
An oil tanker 3m wide 2 m deep and 10 m long contains oil of density 800 kg/m3, if the tanker is closed and completely filled with the oil and accelerated horizontally at 3m/s2. a.) determine the total liquid thrust (hydrostatic force) on the front end. (in kN) b.) determine the total liquid thrust (hydrostatic force) on the rear end. (in kN)
4. The right limb of a simple U-tube manometer containing mercury is open to the atmosphere while the left limb is connected to a pipe in which a fluid of sp.gravity 0.9 is flowing. The centre of the pipe is 12 cm below the level of mercury in the right limb. Find the pressure of fluid in the pipe if the difference of mercury level in the two limb is 20 cm . And also draw the arrangements.