• The cost of a 1-o overhead feeder is OMR 6 a per km ( a is area of cross section in sq mm) and the interest and depreciation charges on feeder are 10%. Determine the most economical current density to use for transmission requiring full load current for 50% of the year. The cost of generating electrical energy is 10 baisa per unit. Assume resistance of 1 m length and 1 mm? section of conductor as 1/58 ohm.

• The cost of a 1-o overhead feeder is OMR 6 a per km ( a is area of cross section in sq mm) and the interest and depreciation charges on feeder are 10%. Determine the most economical current density to use for transmission requiring full load current for 50% of the year. The cost of generating electrical energy is 10 baisa per unit. Assume resistance of 1 m length and 1 mm? section of conductor as 1/58 ohm.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

can you fix my code: using JuMP, Gurobi DCOPF = Model(Gurobi.Optimizer); NoLoadCost = [400 500]; Cost = [26 29 33 37;44 52 60 68]; Pseg1 = [10 20]; Pseg2 = [20 20]; Pseg3 = [20 20]; Pseg4 = [20 20]; Pmin = [0 0]; @variable(DCOPF, 0 <= P1total <= 70); @variable(DCOPF, 0 <= P2total <= 80); @variable(DCOPF, -50 <= F13 <= 50); @variable(DCOPF, -50 <= F12 <= 50); @variable(DCOPF, -50 <= F23 <= 50); @variable(DCOPF, Pmin[i] <= P1[i= 1:2] <= Pseg1[i]); @variable(DCOPF, Pmin[i] <= P2[i= 1:2] <= Pseg2[i]); @variable(DCOPF, Pmin[i] <= P3[i= 1:2] <= Pseg3[i]); @variable(DCOPF, Pmin[i] <= P4[i= 1:2] <= Pseg4[i]); @variable(DCOPF, -1 <= theta1 <= 1); @variable(DCOPF, -1 <= theta2 <= 1); @variable(DCOPF, -1 <= theta3 <= 1); @objective(DCOPF, Min, 400 + Cost[1,1]P1[1] + Cost[1,2]P2[1] + Cost[1,3]P3[1] + Cost[1,4]P4[1] + 500 + Cost[2,1]P1[2] + Cost[2,2]P2[2] + Cost[2,3]P3[2] + Cost[2,4]P4[2]); @constraint(DCOPF, P1total == P1[1] +…
Please check the formula logic and the formula for my solution for answer a Alo please check the formula and calculation for the part b. I got confused about the conversionts and not sure if i did it all correct way. a) The transmission time of a frame can be calculated as follows: Propagation delay (Tp) = distance/speed = 5km / 200000 km/s = 0.025ms Transmission time (Tt) = frame size/bandwidth = 10000 * 8bits / (1Mbps * 10 ^ 6) = 0.008sec = 8ms Total time for transmission = 2 * Tp + Tt(since the frame has to travel from A to D and then D to A) = 2 * 0.0025ms + 8ms = 0.005ms + 8ms = 8.005ms The transmission time of the frame from A to D is 8.005 ms. b) To calculate the efficiency of the CSMA/CD protocol in this LAN, we can use the formula: Efficiency = (1 / (1 + 5tprop / tframe)) tprop is the propagation delay tframe is the time it takes to transmit a frame. To calculate tprop, we need to determine the time it takes for a signal to propagate through the 5 Km distance…
Reduce the block diagram a) Reduce the block diagram b) Replace the values (c) Use the Routh-Hurwitz criterion to determine the stability of the system, is the system stable? is the system stable?
choose correct answerA machine cycle requires at least 1-T state 3-T states 6-T states 4-T statesWhich of the following peripheral interface Intel 8255 ports is buffered?NonePort CPort BPort AIn asynchronous data transfer, sending one byte requires additionalThree bitsEleven bitsOne bitOne byteIf the status signals S1=1 and S0=0, the status is WriteReadFetchHalt
S-curve model of diffusion: (true/false) and reasoning a. k = 0, the rate of diffusion is instantaneous? b. fixed k ≥ 0, the carrying capacity is determined only by the ratio of a and b? c. fixed k ≥ 0, the rate of diffusion is determined only by the ratio of a and b? please provide crt ans do not copied from another web site
Note: Please do not handwritten. Also, answer the question by Poles and Zeros of the System Function H(z) & Comments on System Causality and Stability (LTI system).
I really can't read these, please if you could write it down on paper/digital paper or using LibreOffice or MS Office Word with Equation Operators. VL=V×RLRL+RSVL=20×180220+180VL=9 V IR=IL=VRs+RLIR=IL=20220+180IR=IL=0.05IR=IL=50 mA VL=V×RLRL+RSVL=20×470220+470VL=13.623 V IL=10470IL=21.277 mA Is=20-VzRsIs=20-10220Is=45.455 mA Iz=Is-ILIz=45.455 mA- 21.277 mAIz=24.178 mA
A set of five readings is stored in maemory location starting at C060H. Devlop assembly language program (ALP) for 8085 microprocessor to sort the reading in descending order. draw the flow chart for the same.
Subject telecomicatohs engineeting
What is falaification and fabricating data ? Explain with a short example please quickly
1-Explain the importance of Traffic Engineering in Telecommunications and discuss the parameters of tele-traffic 2-Discuss the applications of WLL in a cellular network.
OSPF autonomous systems employ the OSPF Area variable (OSPF AS).