The coupled shafts shown are transmitting 270 hp at 600 rev/min. The shafts are connected by a coupling with eightbolts. The bolt circle diameters are 5 and 10 in.NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part.O0600 rev/minDetermine the minimum nominal shoulder diameter of a bolt if all bolts are to have the same diameter and not exceed a shear stress of20 kpsi Select a preferred fraction size.The minimum nominal shoulder diameter of a bolt is,in.

Answered: Image /qna-images/answer/92707be8-c137-4920-a48a-732b7a78ba17.jpg

The coupled shafts shown are transmitting 270 hp at 600 rev/min. The shafts are connected by a coupling with eight bolts. The bolt circle diameters are 5 and 10 in. NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part.

The coupled shafts shown are transmitting 270 hp at 600 rev/min. The shafts are connected by a coupling with eight bolts. The bolt circle diameters are 5 and 10 in. NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The disc clutch of an automobile is carried on a 2-inch 6-splined shaft and not to slide under load. The nominal dimensions are as follows: b = 0.25 D; t = 0.075 D and d = 0.85 D. The hub length of 150 % of shaft diameter. Determine the total horsepower transmitted at 3,600 rpm, if the yield strength of the shaft is 1,400 psi
Two short shafts with identical diameters of 38.1 mm are connected by a coupling which is fitted with 4 - bolts on a 100 mm bolt circle. The shaft runs at a speed of 400 rpm. The design shearing stress of the bolts is 12 N/mm and the design compressive stress of flanges is 15 N/mm. What is the power transmitted by the short shaft in kW? A. 24.1 kW B. 22.7 kW C. 26.5 kW D. 28.3 kW What diameter of the bolt should be used? A. 18.32 mm B. 20.64 mm C. 16.28 mm D. 14.46 mm How thick should the flanges be in mm? A. 13.02 mm B. 15.54 mm C. 9.07 mm D. 11.51 mm
Design a typical rigid flange coupling for connecting a motor and a centrifugal pump shafts. The coupling needs to transmit 15 KW at 1000 rpm. The allowable shear stresses of the shaft, key and bolt materials are 60 MPa, 50 MPa and 25 MPa respectively. The shear modulus of the shaft material may be taken as 84GPa. The angle of twist of the shaft should be limited to 1 degree in 20 times the shaft diameter. Note: show complete handwritten solution
A plain flange coupling is used by a 75 mm shaft to transmit 50 kW at 100 rpm. It uses 6 bolts with a diameter of 20 mm. Determine the bolt circle diameter if the shearing stress of the bolt is 25 MPa. A. 102.32 mm B. 202.64 mm C. 152.16 mm D. 252.78 mm
A coupling must transmit 30 hp at a speed of 175 r/min. 3/8 inch diameter bolts are arranged in a single 6 inch diameter circle. The shear stress in the bolts should not exceed 5,000 psi. What is the minimum number of bolts that should be used? Answer: seven bolts
A drive shaft running at 2500 rpm has outer diameter of 60mm and innerdiameter of 40mm. The allowable shear stress in the shaft is 35MPa. Determine themaximum power that can be applied. Present drawings/FBD’s illustrating your solution.
Torque in = 40nm Holding torque out = 896nm 8.Using your answers from the gear box above, and given that the input shaft has a diameter of 12 mm and the output shaft has a diameter of 15 mm, both shafts are made from aluminium. When this transmission system was operated, it failed. Identify the position where the failure occurred and the reason for this failure. Suggests improvements to the system to overcome the failure mode. The shear strength of aluminium is 207 MPa.
A 1.5-inch Monel shaft is used in a torsional application. Based on the operating speed of 100 rpm and factor of safety of 12. How much horsepower can it transmit? Assume the shearing stress is ¾ of the ultimate tensile stress which is 100 ksi.
A flanged bolt coupling consists of eight – 10mm diameter steelbolts on a bolt circle 500mm in diameter and six – 12mm diametersteel bolts on a concentric bolt circle 350mm in diameter. Whattorque can be applied without exceeding a shearing stress of75MPa in the bolts (Gst = 82GPa)
3. Find the power that can be safely transmitted by a flange type shaft coupling, if it has four equally spaced studs all at a radius of 50 mm from the shaft centre. The mean stud diameters are 12.5 mm, and each stud has a maximum safe working shear stress of 86 MPa. The shaft rotates at 3600 rpm.
A drive shaft running at 2500 rpm has outer diameter of 80mm and innerdiameter of 60mm. The allowable shear stress in the shaft is 40MPa. Determine themaximum power that can be applied.
1.1. State three underlying assumptions in the formulation of the torsion formula, .TGJrl (3) 1.2 A hollow shaft has to be designed for a marine engine delivering 1200 kW when running at 120 r/min. The maximum allowable shear stress is 50 MPa and the maximum torque to be transmitted by the shaft is 30 % greater than the mean torque. The internal diameter of the shaft is 50 % that of the external diameter. Calculate: 1.2.1 The dimensions of the shaft and the angle of twist of the shaft over 3 m when transmitting the above torque (G = 80 GPa). (14) 1.3 Determine the torsional rigidity of a 300 mm long steel shaft with a diameter of 50 mm. (G = 80 GPa