The crankshaft of a two-stroke engine spins at about 391 RPM for a brake torque of 983 N-m. If the engine has a total of 4 cylinders, each of which is 28.5cmx30.5cm and double acting, calculate the brake mean effective pressure in Pa.

Q: Find the Normal Force (in kilo-Newtons) in the rod of the system.

A:

Q: Car A moves in a straight line while Car B moves along a curve having a radius of curvature of 200 m...

A:

Q: 1-A 60 Hz generator supplying 60% of Pmax to an infinite bus trough a reactive network. A fault occu...

A: Let  p m be the max power  that can be discribedpmsinδ0=0.6 =psδ0=36.86°=0.643 radians durms the fau...

Q: Q3(a) A wood beam with a rectangular section is found to have the insufficient load capacity. So an ...

A: according to the given details 

Q: Determine the normal force, shear force, and moment at a section through point C. Take P = 8 kN B 0....

A: Given: P =8 kN Answers: normal force = 30 kN shear force = 8 kN moment = 6 kNm

Q: Determine the internal stresses developed in bars JH and HY when bar JH experiences a change in temp...

A:

Q: Two liquids of different densities (= 1500 kg/m3 , = 650 kg/m3) are poured together in to a 100 – li...

A: Calculated the respective amounts of liquid used. Also, calculate the weight of the mixture.

Q: At the instant shown, bar AB has a constant counterclockwise angular velocity of 4 rad/s. Determine ...

A:

Q: Consider the compound shaft KC which is compose of a 1200mm long solid rod fitted snuggly into an eq...

A:

Q: Locate the centroid (x, y) of the shaded area below. (Use a vertical differential elemerit) y 25y = ...

A:

Q: Calculate the specific weight and density of methane at 100OF and 120 psia.

A: The ideal gas equation is an equation of state of hypothetical ideal gas. It states that the product...

Q: 2.) (2 points) The cylinder as shown below weighs 1000 N. It is supported by a rod with a cable at p...

A:

Q: A refrigerator has a broken light bulb inside that is constantly turned on even when the refrigerato...

A: Given:Power of light bulb, P=20 WCoP of refrigerator=1.4Electricity cost=12/ kWh

Q: The basketball player likes to release his foul shots with an initial speed vo = 25.5 ft/sec. What 2...

A:

Q: 1. Lea walks 20m north, 35m east, 10m north, and then 6m west before stopping. What is her displacem...

A:

Q: For the gear train shown, the diameters of the three solid shafts are: dAB = 20 mm, dco = 25 mm, dgf...

A:

Q: Problem (5.3) The outlet angles of the nozzle and blades of a two-row impulse turbine are in success...

A:

Q: Compute energy loss that would occur as 27 gal / min of water flows from a tank into a steel tube wi...

A:

Q: 2-Explain the concepts a) Small disturbance (small signal) stability b) Large disturbance (Transient...

A: a) Small Disturbance (small signal ) stability Definition : Small Signal stability its also called a...

Q: 2. Link BD is made of brass (E = 103 GPa ) and has a cross-sectional area of 258 mm?. Link CE is mad...

A:

Q: 8:3m V.A ヒo2m-メ Determine Cantroid Y dmax if M= 5 K N.n

A:

Q: The cylinder as shown below weighs 1000 N. It is supported by a rod with a cable at point B. Determi...

A: The strain force is the power that is communicated through a string, rope, link or wire when it is p...

Q: The crane BC shown below lifts a load of W. Neglecting the weight of the crane. Determine the follow...

A:

Q: At the instant shown, bar AB has a constant counterclockwise angular velocity of 4 rad/s. Determine ...

A:

Q: A horizontal flow field has the following velocity components: u = (y2 – x2) m/s = (2xy) m/s a) The ...

A: Velocity equations: u= (y2 - x2) m/s v= (2xy) m/s Pressure at point A (3m, 2m), P1= 600 kPa Pressure...

Q: The particle P starts from rest at point A at time t = 0 and changes its speed thereafter at a const...

A:

Q: 5. When unloaded, bars AB and AC are each 36 - in long and have a cross-sectional area of 2 in. Thei...

A:

Q: 2. Link BD is made of brass (E = 103 GPa ) and has a cross-sectional area of 258 mm2. Link CE is mad...

A:

Q: Q1/ Replace the two belt tensions by an equivalent force-couple system at A 400 ib 35 4.in 250 lb

A:

Q: Unit pump injection system is an integrated fuel injection system, combining a fuel injector and a h...

A: We know that the unit pump injection system is a high pressure integrated direct fuel injection syst...

Q: Air at 1 atmosphere and a temperature of 60f enters 1/2-in. id tube with a velocity of 80 fps. The w...

A: Given information Pressure of air entering = 1 atmTemperature = 60°F = 288.7056 KDiameter of tube = ...

Q: A heat treat steel plate measures 3 m *1 m and is initially at 30 degree Celsius. It is cooled by bl...

A: Given: The plate area, A = 3 m x 1 m The temperature of plate, T = 30o The length of the plate, L = ...

Q: For a given actual Rankine Cycle, the actual enthalpy at the end of the isentropic expansion can be ...

A:

Q: Q2/ Determine the maximum allowable load P that can be safely suppom 1.5 in. and b-4 in. The wood ha...

A: t=1.5inb=4inσfail=2ksiζfail=2ksiFOS=1.5   To-Find:- P=?

Q: 1. In a Rankine cycle, steam enters the turbine at 2.5 MPa and condenser at 50 kPa, what is the ther...

A: Answer: The thermal efficiency of the cycle is 25.54%.  

Q: What is the column (small, intermediate or long) if the radius of gyration is greater than the allow...

A: A column is a vertical member which is subjected to axial compressive load and failure of the column...

Q: 2.)A race car starts accelerating at a = 5 and continues to do this for 10 seconds. What is its fina...

A: GIVEN DATA- ACCELERATION a=5m/s2 INITIAL VELOCITY u=0m/s TIME t=10 sec WE HAVE TO CALCULATE THE FINA...

Q: HAT IS THE BASIC DIFFERENCE BETWEEN A REFRIGERATION SYSTEM APPLIED IN AN AIR CONDITIONING AND IN THE...

A:    Refrigeration is the process of lowering and/or maintaining a space, material, or system's temper...

Q: A Pelton wheel turbine is to operate under a head c 25 m at 200 r.p.m. If the discharge is 9 m/s and...

A:

Q: The strains on the surface of an experimentaldevice made of pure aluminum (E = 70 GPa,n = 0.33) and ...

A: Given   Pure aluminum: E = 70 GPa           Poisson ratio = 0.33 Find   Stress in the x direction

Q: 9. A 100-kg wooden box, starting from rest, is pulled across a floor with a constant horizontal forc...

A:

Q: bulk modulus of elasticity of oil ?

A: Given: Oil in hydraulic cylinder is compressed from an initial volume:  V1=3 m3   V2=1.98 m3If the p...

Q: 2 m 1 m 2 m This is not your oproperty so do ousfin any 37 www 1.5 m your 1.5 s B In the assembly sh...

A:

Q: Determine the constant speed of the passengers on the amusement-park ride if it is observed that the...

A:

Q: what is the present worth of 54000 due in five years if money is worth 11% and is compounded semi an...

A:

Q: Given the bended rod as shown below. Determine the following: a.) The x-component of Reaction A. b.)...

A: GIVEN DATA- A LOADED BAR GIVEN WE HAVE TO FIND REACTION FORCES

Q: PROBLEM 2 In the assembly shown, sags of s and 1.5 s resulted when the two cylinders were suspended ...

A:

Q: Solve the problem stated below. Use bond papers and black ball pen. Make your solution clear and cle...

A:

Q: A horseshoe player releases the horseshoe at A with an initial speed vo = 36 ft/sec. Determine the r...

A:

Q: v, what is the brake power in kW?

A: To find Brake power

Clutches, Brakes, Couplings, and Flywheels

The clutch is described as a machine element used to connect or disconnect two shafts together to transmit torque or power. The clutch works on the principles of friction. The clutch is commonly used in automobiles to transfer power from the driving shaft to the driven shaft.