The cross-section of a composite beam made of aluminium and steel is shown in the figure. The moduli of elasticity are E_{a} = 75GPA and E_{s} = 200 GPa. Under the action of a bending moment about z-axis that produces a maximum stress of 50 MPa in the aluminium, what is the maximum stress o in the steel? %3D %3D Aluminium Steel 30 mm - ww 08

The cross-section of a composite beam made of aluminium and steel is shown in the figure. The moduli of elasticity are E_{a} = 75GPA and E_{s} = 200 GPa. Under the action of a bending moment about z-axis that produces a maximum stress of 50 MPa in the aluminium, what is the maximum stress o in the steel? %3D %3D Aluminium Steel 30 mm - ww 08

Materials Science And Engineering Properties

1st Edition

ISBN:9781111988609

Author:Charles Gilmore

Publisher:Charles Gilmore

Chapter6: Introduction To Mechanical Properties

Section: Chapter Questions

Problem 6.4P

See similar textbooks

Similar questions

Estimate the elastic and plastic strain at the ultimate tensile strength in the low-carbon steel specimen in Figure 6.16.
An aluminum alloy [E = 70 GPa; v = 0.33; a = 23.0×10-6/°C] bar is subjected to a tensile load P. The bar has a depth of d = 260 mm, a cross-sectional area of A = 14720 mm2, and a length of L = 5.5 m. The initial longitudinal normal strain in the bar is zero. After load P is applied and the temperature of the bar has been increased by AT = 46°C, the longitudinal normal strain is found to be 1680 µɛ. % D Calculate the change in bar depth d after the load P has been applied and the temperature has been increased. L P Answer: Ad = i mm
Narrow bars of aluminum are bonded to the two sides of a thick steel plate as shown. Initially, at T₁ = 70°F, all stresses are zero. Knowing that the temperature will be slowly raised to T₂ and then reduced to T₁, determine (a) the highest temperature T₂ that does not result in residual stresses, (b) the temperature T₂ that will result in a residual stress in the aluminum equal to 58 ksi. Assume aa = 12.8 x 10-6/°F for the aluminum and a = 6.5 × 10-6/°F for the steel. Further assume that the aluminum is elastoplastic with E = 10.9 × 106 psi and ay = 58 ksi. (Hint: Neglect the small stresses in the plate.) Fig. P2.121
An aluminum alloy [E = 67 GPa; ν = 0.33; α = 23.0 × 10–6/°C] plate is subjected to a tensile load P. The plate has a depth of d = 225 mm, a cross-sectional area of A = 5100 mm2, and a length of L = 4.1 m. The initial longitudinal normal strain in the plate is zero. After load P is applied and the temperature of the plate has been increased by ΔT = 63°C, the longitudinal normal strain in the plate is found to be 2900 με. Determine: (a) the magnitude of load P. (b) the change in plate depth Δd.
1.4-7 The data shown in the table below were obtained from a tensile test of high-strength steel. The test specimen had a diameter of 13 mm and a gage length of 50 mm (see figure for Prob. 1.4-3). At fracture, the elongation between the gage marks was 3.0 mm and the minimum diameter was 10.7 mm. Plot the conventional stress-strain curve for the steefor the steel and determine the proportional limit, modulus of elastics of elastic- ity (i.e., the slope of the initial part of the stress-strain,tress-strain curve), yield stress at 0.1% offset, ultimate stress, percent, elongation in 50 mm, and percent reduction in area. 'ess, percent area. TENSILE-TEST DATA FOR PROB. 1.4-7 Elongation (mm) 0.005 0.015 0.048 Load (kN) 5 10 30 50 0.084 60 0.099 64.5 0.109 67.0 0.119 68.0 0.137 69.0 0.160 70.0 0.229 72.0 0.259 76.0 0.330 84.0 0.584 92.0 0.853 100.0 1.288 112.0 2.814 113.0 Fracture
An aluminum alloy [E = 74 GPa; v = 0.33; a = 23.0 x 10-6/°C] plate is subjected to a tensile load P. The plate has a depth of d = 265 mm, a cross-sectional area of A = 5300 mm², and a length of L= 4.2 m. The initial longitudinal normal strain in the plate is zero. After load P is applied and the temperature of the plate has been increased by AT = 57°C, the longitudinal normal strain in the plate is found to be 2920 με. Determine: (a) the magnitude of load P. (b) the change in plate depth Ad. L P Answer: (a) P = i (b) Δd = i kN mm
An aluminum alloy [E = 72 GPa; v = 0.33; a= 23.0 x 10-6/°C] plate is subjected to a tensile load P. The plate has a depth of d = 245 mm, a cross-sectional area of A = 5500 mm², and a length of L = 6.0 m. The initial longitudinal normal strain in the plate is zero. After load P is applied and the temperature of the plate has been increased by AT = 69°C, the longitudinal normal strain in the plate is found to be 3340 μc. Determine: (a) the magnitude of load P. (b) the change in plate depth Ad. L P Answer: (a) P = i (b) Δd = i KN mm
An aluminum alloy [E = 73 GPa; v = 0.33; a= 23.0 x 10-6/°C] plate is subjected to a tensile load P. The plate has a depth of d = 250 mm, a cross-sectional area of A = 6900 mm², and a length of L = 5.9 m. The initial longitudinal normal strain in the plate is zero. After load P is applied and the temperature of the plate has been increased by AT = 50°C, the longitudinal normal strain in the plate is found to be 2400 με. Determine: (a) the magnitude of load P. (b) the change in plate depth Ad. L Answer: (a) P = i (b) Δd = KN mm
The following information about the o-e curve is given for a steel alloy. E = 0.001527 at o = 300 MPa and ɛ = 0.003054 for o = 600 MPa. (a) Draw the stress-strain diagram and calculate the E for this alloy.
In the figure shown below, determine: 1) The final temperature if the normal stress at aluminium is Og = -90 MPa and the initial temperature %3D 20°C. 2) The final length of the aluminium member. Aluminum A=1800mm? Bronze A=1500mm? E=73GPA E=105GPA a=23.2x10-6/°C a=21.6x10-6/°C Gap=0.5mm 0.35m 0.45m
If it is constrained between two supports A and B and is stress-free at 20 ℃, what would be the stress in the two materials when it is heated to 70 ℃, For Steel: Es = 210 GPa, Coefficient of expansion = 12x10^6/℃. For Brass: Eb = 105 GPa, Coefficient of expansion = 19x10^-6/℃
A steel with E = 29 000 ksi with a rectangular cross-section is bent over a rigid mandrel with R = 15 in as shown in the figure. If the maximum flexural stress in the bar is not to exceed the yield strength of 36 ksi, determine the allowable thickness h of the bar.