stressshow complete solutionand provide the -given-required-FBD-formula and solution4qwqw The cross-sectional area of each member of the truss is 1.8 sg.in. Calculate thestress in ksi in member DE. Indicate tension or compression. Express your answerto two decimal places. Do not include the unit. Ex. If your answer is 10.50 ksi andit is compression, type: 10.50 (C) *Your answerThe cross-sectional area of each member of the truss is 1.8 sg.in. Calculate thestress in ksi in member DF. Indicate tension or compression. Express your answerto two decimal places. Do not include the unit. Ex. If your answer is 10.50 ksi andit is compression, type: 10.50 (C) *Your answer STRESSThe cross-sectional area of each member of the truss is 1.8 sq.in. Calculate thestress in ksi in member CE. Indicate tension (T) or compression (C). Express youranswer to two decimal places. Do not include the unit. Ex. If your answer is 10.50ksi and it is compression, type: 10.50 (C) *D6 ftB8 ft8 ftE8 ft6 ft30 kipsYour answer

Given: cross-section area; A = 1.8 in2 RA and RF are the support reactions. RA =(8/24)*30 =10 kips…

The cross-sectional area of each member of the truss is 1.8 sq.in. Calculate the stress in ksi in member CE. Indicate tension (T) or compression (C). Express your answer to two decimal places. Do not include the unit. Ex. If your answer is 10.50 ksi and it is compression, type: 10.50 (C) * 6 ft B 8 ft 8 ft E 8 ft 6 ft 30 kips

The cross-sectional area of each member of the truss is 1.8 sq.in. Calculate the stress in ksi in member CE. Indicate tension (T) or compression (C). Express your answer to two decimal places. Do not include the unit. Ex. If your answer is 10.50 ksi and it is compression, type: 10.50 (C) * 6 ft B 8 ft 8 ft E 8 ft 6 ft 30 kips

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

For the truss structure below, if the applied force P = 10 kN, what is the force in member CD? Negative sign must be included if compression. Answer must also have 1 number past the decimal point and have the proper unit.
The cross-sectional area of each member of the truss is 1.6in2. Calculate the average normal stresses in members CE, DE, and DF. Indicate whether the stress is in tension or compression. Draw free-body diagram
An aluminum pole for a street light weighs4600 N and supports an arm that weighs 660 N (seefigure). The center of gravity of the arm is 1.2 m from theaxis of the pole. A wind force of 300 N also acts in the (-y)direction at 9 m above the base. The outside diameter ofthe pole (at its base) is 225 mm, and its thickness is 18 mm. Determine the maximum tensile and compressivestresses σt and σc, respectively, in the pole (at its base)due to the weights and the wind force.
The given plate below with width of 200 mm andthickness of 16 mm is to be connected to two plates ofthe same width with half the thickness by 20 mmdiameter rivets as shown. The rivet hole is 2 mm greaterthan the rivet diameter. Allowable tensile stress on netarea is 0.6Fy. Allowable bearing stress is 1.35Fy. plate: fy = 241 mpa fu = 4141 mpa rivet: fv = 152 mpa Determine maximum load P for block shear
For the truss given below, it is desired to determine the normal efforts that act on the members, so that, thus, possible constraints for its design are possible. Consider that at point A there is a second gender support; and at point D, a first-class support. As this is asked: what is the effort acting on bar AB? Is it guidance or assessment?Source: Hibbeler (2004, p. 588). HIBBELER, R. C. Resistance of Materials. 5. ed. Rio de Janeiro: Technical and Scientific Books Publisher, 2004. Question 1 options: a) A compression force of 100 kN acts on bar AB. B) A tensile effort of 100 kN acts on bar AB. c) A compressive force of 141.42 kN acts on bar AB. d) A compression force of 200 kN acts on bar AB. e) A tensile effort of 141.42 kN acts on bar AB.
A retaining wall 6 ft high is constructed ofhorizontal wood planks 2.5 in. thick (actual dimension)that are supported by vertical wood piles of a12 in. diameter (actual dimension), as shown in thefigure. The lateral earth pressure is p1 125 lb/ft2at the top of the wall and p2 =425 lb/ft2 at the bottom.(a) Assuming that the allowable stress in the woodis 1175 psi, calculate the maximum permissiblespacing s of the piles.(b) Find the required diameter of the wood pilesso that piles and planks (t = 2.5 in.) reach theallowable stress at the same time.Hint: Observe that the spacing of the piles may begoverned by the load-carrying capacity of either theplanks or the piles. Consider the piles to act as cantileverbeams subjected to a trapezoidal distribution ofload, and consider the planks to act as simple beams between the piles. To be on the safe side, assume thatthe pressure on the bottom plank is uniform andequal to the maximum pressure.
A steam boiler is to have a 300 mm diameter hand placed hole on one end. If themaximum internal pressure is 1.3 MPa, how many 15 mm holes will be required to keepthe cover plate in position? The root diameter of a 15 mm bolt is 12 mm. The allowabletensile stress in the bolts is 100 MPa and the initial stress in the bolts when they aretightened is 600 MPa.
As shown, three steel wires, each 28 mm2 in area, are used to lift a mass M. Their unstretched lengths are 19.99 m, 19.98 m, and 20 m. If M= 1,182 kg. what stress exists in the MIDDLE wire? Use E=215 Gpa. Answer must be in MPa.
A steel rod is acted upon by the loading shown below. 50 mm2 is the area of the circular rod. The coupling sizes at B, C, and D are neglected. Use E st = 200 GPa. c) Force in segment CD, PCD=__________ kN, (insert type of force here) d) Total deformation in the assembly, σ = _____________ mm
Show complete solution using the flexural stress formula.
using the method of sections , analyse the truss shown in figure 8 below reguarding forces in menbers ED , DF AND FC .
41.) A cylindrical steel pressure vessel 400 mm in diameter with a wallthickness of 20 mm, is subjected to an internal pressure of 7.875 MPa. Towhat value may the internal pressure be increased if the stress in the steelis limited to 100 MPa?