The current drawn on no load by a single phase transformer is io = 3 sin (314t - 60°) A, when a voltage vị = 300 sin(314t)V is applied across the primary. The values of magnetizing current and the core loss component current are respectively: (A) 1.2 A & 1.8 A (B) 2.6 A & 1.5 A (C) 1.8 A & 1.2 A (D)1.5 A & 2.6 A

The current drawn on no load by a single phase transformer is io = 3 sin (314t - 60°) A, when a voltage vị = 300 sin(314t)V is applied across the primary. The values of magnetizing current and the core loss component current are respectively: (A) 1.2 A & 1.8 A (B) 2.6 A & 1.5 A (C) 1.8 A & 1.2 A (D)1.5 A & 2.6 A

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter3: Power Transformers

Section: Chapter Questions

Problem 3.32MCQ

See similar textbooks

Similar questions

(a) An ideal single-phase two-winding transformer with turns ratio at=N1/N2 is connected with a series impedance Z2 across winding 2. If one wants to replace Z2, with a series impedance Z1 across winding 1 and keep the terminal behavior of the two circuits to be identical, find Z1 in terms of Z2. (b) Would the above result be true if instead of a series impedance there is a shunt impedance? (c) Can one refer a ladder network on the secondary (2) side to the primary (1) side simply by multiplying every impedance byat2 ?
All values of a transformer are proportional to its __________________ ___________________.
For an ideal 2-winding transformer, an impedance Z2 connected across winding 2 (secondary) is referred to winding 1 (primary) by multiplying Z2 by (a) The turns ratio (N1/N2) (b) The square of the turns ratio (N1/N2)2 (c) The cubed turns ratio (N1/N2)3
An infinite bus, which is a constant voltage source, is connected to the primary of the three-winding transformer of Problem 3.53. A 7.5-MVA,13.2-kV synchronous motor with a sub transient reactance of 0.2 per unit is connected to the transformer secondary. A5-MW,2.3-kV three-phase resistive load is connected to the tertiary Choosing a base of 66 kV and 15 MVA in the primary, draw the impedance diagram of the system showing per-unit impedances. Neglect transformer exciting current, phase shifts, and all resistances except the resistive load.
For an ideal transformer, the efficiency is (a) 0 (b) 100 (c) 50
A single-phase step-down transformer is rated 13MVA,66kV/11.5kV. With the 11.5 kV winding short-circuited, rated current flows when the voltage applied to the primary is 5.5 kV. The power input is read as 100 kW. Determine Req1andXeq1 in ohms referred to the high-voltage winding.
The ratings of a three-phase three-winding transformer are Primary(1): Y connected 66kV,15MVA Secondary (2): Y connected, 13.2kV,10MVA Tertiary (3): A connected, 2.3kV,5MVA Neglecting winding resistances and exciting current, the per-unit leakage reactances are X12=0.08 on a 15-MVA,66-kV base X13=0.10 on a 15-MVA,66-kV base X23=0.09 on a 10-MVA,13.2-kV base (a) Determine the per-unit reactances X1,X2,X3 of the equivalent circuit on a 15-MVA,66-kV base at the primary terminals. (b) Purely resistive loads of 7.5 MW at 13.2 kV and 5 MW at 2.3kV are connected to the secondary and tertiary sides of the transformer, respectively. Draw the per- unit impedance diagram, showing the per-unit impedances on a 15-MVA,66-kV base at the primary terminals.
A single-phase, 50-kVA,2400/240-V,60-Hz distribution transformer has the following parameters: Resistance of the 2400-V winding: R1=0.75 Resistance of the 240-V winding: R2=0.0075 Leakage reactance of the 2400-V winding: X1=1.0 Leakage reactance of the 240-V winding: X2=0.01 Exciting admittance on the 240-V side =0.003j0.02S (a) Draw the equivalent circuit referred to the high-voltage side of the transformer. (b) Draw the equivalent circuit referred to the low-voltage side of the transformer. Show the numerical values of impedances on the equivalent circuits.
This question is so important for me please help me as soon as possible. A single phase 3300/220 V, 11 kVA, 50 Hz transformer has the following values: Primary side: R1=1.125 Ω, Xℓ1=22.5 Ω Secondary side: R2=0.02 Ω, Xℓ2=0.1 Ω Assume that the exciting impedance (shunt branch) is connected at the primary terminals. (Directly to the input terminals. Not in the middle of the equivalent circuit) Draw the approximate equivalent circuit referred to the secondary Find the maximum efficiency when a load of 4.4*e-j8,43 Ω is connected to the secondary terminals having its rated voltage. Find the core loss resistance (Rc). 3. Draw the phasor diagram.
The following values were seen in the measurements made separately by the primary and secondary of a 220/270 V phase transformer. R1 = 4 ohms, X1 = 4.6 ohms, R2 = 0.89 ohms, X2 = 1.79 ohms; R2T = 8.7 ohms, X2T = 8.8 ohms (total values measured on the secondary side), Xm = 60 ohms, Rfe = 750 ohms, (using a T-type equivalent circuit) c.) Active and reactive powers drawn from the transformer d.) Calculate the efficiency of the transformer.
A 10 kVA, 2400/240-V single-phase transformer has the following resistances and reactances. Find the equivalent resistance when referred to secondary (R02) R1 = 3, R2 =0.03, X1 =15, x2 =0.150 Group of answer choices 2.5 0.004 0.05 0.06
A single-phase, 2 kV/ 200 V, 50 Hz transformer has primary resistance of 3.5 Ω and reactance of 4.5 Ω. The secondary resistance and reactance are 0.015 Ω and 0.02 Ω respectively. Find equivalent complex impedance referred to primary.