The DC voltage and peak-to-peak ripple voltage across the load resistance of an inductor filter connected to a bridge rectifier is 70 V and 2 V, respectively. What is the ripple factor? 0.09 0.5 1 0.0101

The DC voltage and peak-to-peak ripple voltage across the load resistance of an inductor filter connected to a bridge rectifier is 70 V and 2 V, respectively. What is the ripple factor? 0.09 0.5 1 0.0101

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter30: Dc Motors

Section: Chapter Questions

Problem 6RQ: What is CEMF?

See similar textbooks

Related questions

Q: What is the PIV across each diode of a bridge rectifier with a secondary voltage of 20 V rms? * O…

Q: For uncontrolled half wave rectifier, R=80ohm, L=0.15H, f=50Hz and Vm=311V. Calculate the average…

A: R=80ohm, L=0.15H, f=50Hz and Vm=311V.

Q: Determine the ripple factor for the filtered bridge rectifier with a load as indicated in Figure…

A: The output in a rectifier is desired to be DC. The ripple factor is a term to decide how much of…

Q: Draw the input waveform and output waveform for the circuit given below with proper values marked in…

A: Given, D1 -> Germanium diode, the On-state voltage drop is 0.3 V D2-> Silicon diode, the…

Q: Power supply circuit is delivering 0.5 A and an average voltage 20 V to the load as shown in the…

A: The given circuit is a half wave rectifier circuit from the relation of ripple voltage at the output…

Q: We want a peak load voltage of 40 V out of a bridge rectifier. What is the approximate rms value of…

A: The full wave bridge rectifier is an AC to AC converter. it produces an pulsating dc with same peak…

Q: The RMS output voltage ofa Full-Wave Bridge Rectifier is 20 volts, Calculate the average current (in…

A: for full bridge rectifier RMS value of output voltage Vrms= Vm2…

Q: A full wave rectifier has load resistance 500ohm and the used diodes has internal resistance Of…

A: Given Data: RL = 500 ohm Ri = 50 ohm turns ratio from primary to half of secondary = 5 :1 Vs = 240 V

Q: To get a peak output voltage of 40V in a bridge rectifier, What is the approximate rms value of…

Q: Calculate the peak voltage across each half of a centre-tapped transformer used in a full-wave…

A: In this question we will find peak collage across each half of secondary of center tapped…

Q: Calculate the ripple voltage of a full-wave rectifier with a 75uF filter capacitor connected to a…

Q: Q5)The full wave-controlled bridge rectifier has an ac input of 120 V rms at 50Hz and a 202 load…

A: The given rectifier is a full-wave controlled bridge rectifier, the RMS current is given by the…

Q: Power supply circuit is delivering 0.5 A and an average voltage 20 V to the load as shown in the…

Q: Determine Vp(rect), Vr(pp), VDc(filter) and the Ripple factor F 10:1 D3 DI 110 V rms Output V písec)…

A: The given circuit diagram is shown below:

Q: The single-phase halt wave rectifier has a L= 6.5 mH, R = 0.5 2, and E = 10 V. The input voltage is…

A: It's given that : L=6.5mHR=0.5ΩE=10VVs=120VVm=1202f=60Hzα=60 or 1.047radian

Q: In the operation of a half-wave rectifier with a capacitor-input filter, the ripple factor can be…

A: we are know that ripple Voltage of Half wave Rectifier Vr=Vpeakf×RL×C RL= Load Resistance

Q: The approximated peak voltage across each half of a center-tapped transformer used in full-wave…

A: Rectifier is an device which convert alternating signal in to pulsating direct signal. The half wave…

Q: 30°, the average value of output current in A single-phase full-wave transistor rectifier feeds…

A: We need to find a average output current in the given 1 phase full wave rectifier having RLE load

Q: feeds power to motor load. The source A single-phase full-wave transistor rectifier feeds power to…

A: In this question we need to find a average value of output voltage of rectifier.

Q: 1. A base line stabilizing circuit * (2 Points) Rectifiers and filters a sine wave Converts a dc…

A: A base line stabilizing circuit is used to shift or reinsert a DC component at the circuit output…

Q: For a full-wave controlled rectifier, find out the RMS output voltage

A: Given data Vm = 220

Q: A half-wave rectifier is connected to a 8910 load in parallel with a capacitor, if the supply…

A: Given : In the given question they have mentioned a half wave rectifier with a RC filter. Here…

Q: In a full wave bridge rectifier, the transformer secondary voltage is 10sinwt. The forward…

A: NOTE: Since you have posted a question with multiple subparts, we will solve the first three…

Q: The supply current of semi-converter(semi-controlled rectifier) with highly inductive load consists…

A: In this question we need to choose a correct options.

Q: A three phase full wave rectifier is shown below. The input peak phase voltage is assumed equal to…

A: In this question, Choose the correct option What is TUF? TUF = dc output power/ input ac power.

Q: Q2. Determine the ripple factor for the full-wave rectifier circuit with LC filter shown below. 180…

A: Circuit diagram is given, From the circuit diagram, L= 180 mH, C=440 μF, ω=100π

Q: In the operation of a half-wave rectifier with a capacitor-input filter, the ripple factor can be…

A: by changing the value of the filter capacitor or the load resistor the value of the ripple factor…

Q: Power supply circuit is delivering 0.5 A and an average voltage 20 V to the load as shown in the…

Q: highly inductive load is to be supplied from a single-phase supply of 240V and 50HZ. Compare the…

A: In this question, We need to determine the output voltage by fully controlled and half controlled…

Q: For the bridge rectifier circuit shown in the Figure, assuming practical diodes, the peak value of…

Q: In a full wave bridge rectifier, the transformer secondary voltage is 20sinwt. The forward…

A: Full wave bridge Rectifier. Secondary voltage of the transformer is 20sin(wt). Forward resistance…

Q: If a half-wave rectifier is used with 117-V rms ac, the average dc output voltage is about: O 117 V…

A: Out put DC voltage of half wave rectifier is given as Vo=(Vm/π) Where Vm= maximum voltage Vm= √2…

Q: For the bridge rectifier circuit shown in the Figure, assuming practical diodes, the peak value of…

A: We need to find out peak voltage and voltage across resistor .

Q: Q5: The peak value of the input to a full-wave bridge rectifier is 10 V. The approximate average…

A: In this question we need to find a average value of output voltage of the given rectifier

Q: For uncontrolled half wave rectifier, R=80ohm, L=0.15H, f=50Hz and Vm=311V. Find the point when the…

Q: In a rectifier circuit, DC output voltage and RMS output voltage is 0.28 V & 0.67 V respectively.…

A: given DC voltage = 0.28 volts RMS voltage =0.67 volts definition of ripple factor =ripple…

Q: During the operation of a half-wave rectifier with a capacitor- filter, the ripple factor can be…

Q: A 1 - ∅ full-wave rectifier is made by using thyristors. If the peak value of the sinusoidal input…

A: A simple problem on power electronics. Given , delay angle * = )45degrees. ANd peak value of…

Q: Power supply circuit is delivering 0.5 A and an average voltage 20 V to the load as shown in the…

A: Given Output voltage = Vdc=20V Current=0.5A Resistance=R= 20/0.5 = 40 ohm Frequency= 50 Hz Ripple…

Q: the load current is 5 mA and the filter capacitance is 1000UF, what is the eak to-peak ripple out of…

Q: The approximated peak voltage across each half of a center-tapped transformer used in full-wave…

A: Average output voltage V0= 100 v The maximum output voltage for centre tapped transformer full…

Q: In the operation of a half-wave rectifier with a capacitor-input filter, the ripple factor can be…

A: We need to fill the blank space . We need to tell about the half wave rectifier ripple factor .

Q: 2. A Half-Wave rectifier with a capacitor filter (capacitance is 4700 uF) supplies to a load an…

A: The given information about a half-wave rectifier with a capacitor filter: Average load voltage is…

Q: The approximated peak voltage across each half of a center-tapped transformer used in full-wave…

A: An device which convert alternating signal in to pulsating direct signal. The half wave rectifier…

Q: In a rectifier circuit , DC output voltage and RMS output voltage is 0.28 V & 0.67 V respectively.…

A: Average value = 0.28V Rms voltage V= 0.67 Ripple factor?

Q: A single-phase controlled rectifier bridge consists of one SCR and three diodes as shown in figure.…

A: First draw the output voltage waveform and than find the average output voltage. Using average…

Q: By comparing other diodes, reverse recovery time of general purpose diode is higher. Select one: O…

A: The reverse recovery time of general purpose diode is higher. The reverse recovery time of general…

Q: A Half-Wave rectifier with a capacitor filter (capacitance is 4700 µF ) supplies to a load an…

Q: A single-phase half wave uncontrolled rectifier circuit is operating with a purely inductive load…

A: Given data : The given source voltage Vs=100sin277tV The given ammeter reading i=20A

Q: The approximated peak voltage across each half of a center-tapped transformer used in full- wave…

Concept explainers

Analog to Digital Converters

The analog-to-digital converter (ADC) allows circuits controlled by microprocessors, Arduinos, Raspberry Pi, and various reasonable digital circuits to be connected to the real world. In the real world, analog signals have a continuous stream of information from a variety of sources and sensors capable of measuring sound, light, temperature, or movement, in addition to the many digital systems that interact with their environment by measuring analog signals from those transducers.

Question

100%

choose the correct answer?

The DC voltage and peak-to-peak ripple voltage across the load
resistance of an inductor filter connected to a bridge rectifier is 70 V and
2 V, respectively. What is the ripple factor?
0.09
0.5
O 1
0.0101

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1 Introduction

VIEW

Step 2 Calculations

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

What is CEMF?
Exe 1. A half-wave rectifier has a source of 120 V rms at 60 Hz and an R-L load with R=10 Ω and L= 10 mH.Determine, an expression for the load current, the average current, the power absorbed by the resistor, and the power factor. Hint: Beta=3.5 Rad
In a phase controlled full wave rectifier, the source voltage is 50 VRMS sinusoidal, the source frequency is 60 Hz and the load is 20 ohms. Since the delay angle in the circuit is 20 °, which of the following is the value of the RMS load voltage? a) 99.54 V b) 49.77 V c) 70.38 V d) 35.19 V e) 23.46 V
A step-down transformer supplies 25Vrms to a simple half wave rectifier power supply which is connected to a load resistance of 912ohm. The diode breakdown voltage, Vf is 0.7 V. Calculate the amplitude of the peak output voltage, Vpo appearing across the load., calculate the average DC voltage appearing across the load, calculate the DC current in mA drawn by the load.
Consider a three-phase diode rectifier supplying a R = 10 Ω DC load. The supply systemis 440 VLL and 60 Hz. A) What is the value of the average (DC) current across the load?B) Compute the value of an inductive filter (L) to be added in series with the resistiveload to limit the rms value of the lowest order current harmonic to 1% of the DC currentvalue. Note: 2 /[( 1)( 1)] Vdch = Vdc0 h − h + (in rms).
A sinusoidal voltage of 48v, 60 Hz is applied to a half-wave rectifier with dynamic resistance of the diode of .001ohms turns ratio (3:1). Calculate the DC and RMS currents flowing through the load(R=210 ohms). Also calculate the dc output power developed, ac – input power supplied, rectification efficiency, and ripple factor.
Half-wave 60Hz sinusoidal uncontrolled rectifier circuit with a peak voltage value of 100V and a source inductance of 8mH is feeding a highly inductive load of 8A. The average value of the output voltage and power delivered are, respectively and what is the communication angle (u) (Power Electronics)
Matter Energy Transformation, answer the following questions: It is very necessary Answer the following : Draw the simple circuit diagram for half controlled rectifier with R-load. (ii) Draw the output voltage of the load. () Derive an expression for the average output voltage. (iv) Derive an expression for the rms value of the output voltage.
Three-phase half wave rectifier supply resistive load with DC power of 4 kW; the ammeter connected with D1 indicates 8 A r.m.s current, and the source frequency is 50 Hz Due to system inductance the average voltage drops to 96.2% of idealized value ( when the inductance is neglected). How much will the average and r.m.s voltage s be? The r.m.s phase current and average load current Is=? & Idc=? The secondary r.m.s voltage and transformer capacity Vs & KVA? The inductances causes the voltage drop Lc=? The diode forward current and maximum inverse voltage? Now, if the phase B is failed ( disconnected), how much with new dc voltage be in %..Vdc=….% ??
A conductor carries a current that is equivalent to a 5 A continuous current in one direction and a superimposed full-wave rectifier current in the opposite direction. What is the maximum value of the latter if the average conductor current is zero?
Q.1 A single-phase diode bridge rectifier is connected to a grid with rms voltage V, 230V at 50 Hz. Assume that the load is highly inductive, so it could be represented by a constant dc current, Id = 10A. a) Sketch the load voltage and find the average voltage of the load? b) Sketch the source current (grid. AC side) and find the rms value of the source current? c) Determine the fundamental source current and the first three harmonics? Assume Ish_rms ³ 0.91a/h for odd hand 0 otherwise?
A 60-Hz full-wave rectiﬁer is built with a transformer having an rms secondary voltage of 20 V and ﬁlter capacitance C =150,000 μF. What is the largest current that can be supplied by the rectiﬁer circuit if the ripple must be less than 0.3 V?