EY O b rirB/s allنقطة واحدةThe desirable staticcharacteristics ofmeasurements system areprecisionаccuracysensitivityall of theseنقطة واحدةA 0-250 V voltmeter has aguaranteed accuracy of 1% offull-scale reading. Thevoltage measured by thevoltmeter is 180 volts.Determine the limiting error.in percentage1.383.330.3330.138

We need to tell about desirable characteristics of measurement instruments. We need to calculate…

نقطة وا- The desirable static characteristics of measurements system are precision accuracy sensitivity all of these نقطة وا- A 0-250 V voltmeter has a guaranteed accuracy of 1% of full-scale reading. The voltage measured by the voltmeter is 180 volts. Determine the limiting error .in percentage 1.38 3.33 0.333 0.138

نقطة وا- The desirable static characteristics of measurements system are precision accuracy sensitivity all of these نقطة وا- A 0-250 V voltmeter has a guaranteed accuracy of 1% of full-scale reading. The voltage measured by the voltmeter is 180 volts. Determine the limiting error .in percentage 1.38 3.33 0.333 0.138

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

The table gives data for open circuit and short circuit tests on a 6 pole, 440 V, 50 Hz, 3 phase star connected alternator. The effective ohmic resistance between any two terminals of the armature is 0.3 ohm. Field current (A) 2 4 6 7 8 10 12 14 OC Vltage (V) 156 288 396 440 474 530 568 592 S.C current 11 22 34 40 46 57 69 80 Find the regulation at full load current of 40 A at 0.8 power factor lagging, using emf method and mmf method.
FROM THE SOLVE DIAGRAM FOR A COMBINATIONAL ELEMENT ACCORDING TO THE NOMENCLATURE FOR IT, WITH SAT DATA VCC= 18V, VBE= .47V, VBB = 9V, VCE= .92 V ICSATMAX= 290mA. β= 55 RE= 3.3 OHMS WHAT IS THE VALUE OF RB?
1. A resistor, in series with a 138-microfarad capacitor, is connected to a 60-cycle source. If the voltage drop across the capacitor is 115 volts and the power taken by the circuit is 922 watts, calculate (a) the circuit current, (b) the ohmic value of the resistor, (c) the line voltage, (d) the circuit power factor. Please show complete solution and the circuit diagram. Please round off answers up to the 3rd decimal place. Thank you!
A base load station having a capacity of 18 MW and a standby station having a capacity of 20 MW shares a common load. Determine the annual load factors and plant capacity factors of two power stations from the following data:Annual standby station output = 7·35 × 10^6 kWhAnnual base load station output = 101·35 × 10^6 kWhPeak load on standby station = 12 MWHours of use by standby station/year = 2168 hours
Draw a figure of the line that best fits the experimental data in the table(showing experimental points). From the extrapolation of this line, what is the voltage corresponding to a temperature of 110°C? room temperature=25ºC TºC voltage (mV) (millivolts) room temperature 0.2 30ºC 0.4 35ºC 0.7 40ºC 0.9 45ºC 1.1 50ºC 1.3 55ºC 1.6
Dont copy paste need new SOLUTIONs.solve with diagrams with clean Handwriting or understanding solutions A single-phase 60-Hz power line is supported on a horizontal crossarm. The spacing between conductors is 8 ft. A telephone line is supported on a horizontal crossarm 6 ft below the power line. The conductors of the telephone line are AWG No. 14 solid copper (d = 1.6277 mm) spaced 2 ft between centers. The conductors of the power line are AWG No. 2 solid copper (d = 0.2576 in). Find the mutual inductance between the circuits and the voltage per mile induced in the telephone line if the current in the power line is 150 A.
Don't copy others work. Here is one question. Not multiple. Provide full question answer. Sub: Optoelectronic Det: EEE
Please all subpart either dislike is ready please Asap for like Please alll subpart
Two shunt generators and a battery are working in parallel. The open circuitvoltage, armature and field resistances of generators are 250 V, 0.24 ohm, 100ohms and 248V, 0.12 ohm and 100 ohms respectively. If the generators supply thesame current when the load on the bus-bars is 40 A. Calculate the e.m.f. of thebattery if its internal resistance is 0.172 ohm.(Ans. 248
You are a journeyman electrician in an industrial plant. You have been assigned the task of connecting a 25-kW electric heater to a 240-V, single-phase panel. The heater is located in an area with an ambient temperature of 90°F. The conductors are to be copper with Type TW insulation. The heater is expected to operate for more than three hours at a time. What size conductors would you use to connect this heater? Is this correct? I=P/EI=25000 W/ 240 VI= 104.17 amps x 125%I= 130.21 amp/ .96I= 135.63 amp2/0 AWG conductor will be needed
1. A technician is removing an air line from a robot's vertical pneumatic cylinder. He or she is probablyA. bleeding oil from the system.B. equalizing air pressure in the cylinder.C. checking the cylinder and solenoid for leaks.D. looking for signs of water. qual a opcao correta, b, c or d
We are running 3 wires and a ground in a RMC to a control panel with a 60 amp circuit breaker disconnect in the control panel. The conduit is run along the ceiling where the ambient air temperature is 100 degrees. The control panel feeds our secondary cooling pump. What size are the ungrounded conductors? All conductors have typeTHHN insulation. A #6 AWG B 600 Kcmil C #8 AWG D #2 AWG What size RMC do we need? A 3" B 3/4" C 1" D 1 1/2"