The di diameter post CE and dz diameter post DF have connected to the rigid member ABCD. If the posts are made from aluminum and have E=70 GPa, determine the forces that will develop at posts CE and DF due to the applied load P. Also determine the vertical displacement of point A. 2L/3 L/2 B Ca AD 750 mm P 600 mm

The di diameter post CE and dz diameter post DF have connected to the rigid member ABCD. If the posts are made from aluminum and have E=70 GPa, determine the forces that will develop at posts CE and DF due to the applied load P. Also determine the vertical displacement of point A. 2L/3 L/2 B Ca AD 750 mm P 600 mm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A Z-shaped rigid bar ABCD, shown in the figure, issuspended by a pin at B, and loaded by a verticalforce P. At A, a 10-mm-diameter steel tie rod AFconnects the section to a firm ground support at F.Use E = 200 GPa. Determine the vertical deflectionat D.
Two d mm*10 mm cover plates are welded to two UPN 200 channels 100 mm high to form the cross section of the compound beam shown in the figure. The moment of inertia of each channel about a horizontal axis through the centroid is 19.10*106 mm4. a) Determine the support reactions. b) Draw the shear force and bending moment diagrams. c) If the allowable bending stress of the beam is 300 MPa, find the required width d of the plates to safely support the load.
Thumbs-Up will be given. Write the complette solutions legibly. Answer in 3 decimal places. Please answer all since they are all subquestions. Thanks Structural Theory 1d. Determine the vertical reaction R₂ in kN 1e. Determine the shear at midspan between vertical supports in kN. 1f. Determine the maximum factored load moment in the beam in kN.m
A mechanism carries a constant load P applied to the seat asshown.For the angle θ, determine the following(a) the lengths LBE and LAB, in m (b) the angles α and φ, in degreesDraw the complete FBD of(c)members AB, FG, EBH and GHI Calculate the forces, in Newtons, for the following(d) member FG(e) pin H(f) hydraulic cylinder AB given: θ = 39.4°, P= 719 N
A reinforced rectangular beam with width b and effective depth d has 4.16 mm bars placed on 1 layer at the tension side. The beam has a stirrup with a diameter of 10 mm. Use fc=28 Mpa and fy=420 MPa GIVEN: b= 390.5 mm d= 610.5mm L= 6.45 m Wd = 13.5 kN/m WL = 35.5 kN/m Calculate the nominal moment capacity of the beam Calculate that strain of the tension bars. Calculate the strength reduction factor of the beam
Determine the displacement at pulley B. The A992 steel shaft has a diameter of 30 mm.
A reinforced rectangular beam with width b and effective depth d has 4.16 mm bars placed on 1 layer at the tension side. The beam has a stirrup with a diameter of 10 mm. Use fc=28 Mpa and fy=420 MPa GIVEN: b= 350 mm d= 600 mm L= 6 m Wd = 13 kN/m WL = 36 kN/m Calculate the nominal moment capacity of the beam Calculate that strain of the tension bars. Calculate the strength reduction factor of the beam
If the allowable bearing stress for the material under the supports at A and B (σ_(b allow)= 1.5 MPa, determine the size of square bearing plates A’ and B’ required to support the load. Dimension the plates to the nearest mm. The reaction at the supports are vertical. Take P = 100 kN.
q: A load P is supported by a structure consisting of rigid bar BDF and three identical 15-mm-diameter steel E = 200 GPa rods, as shown inthe figure. Use a = 2.787 m, b = 1.901 m, and L= 5 M.For a load of P = 136 kN, determine thedisplacement of joint D. Unit should be in mm
FORCE METHOD An overhang beam ABC is loaded as shown. Determine the reactions at the supports due to loading and a support settlement of 1 mm at the roller B. Take E = 200 GPa and I = 500(10^6) mm^4.
Refer to the given figure below and compute for moment at force C -- (CW+) Mc
Consider the following framing plan below. Squares labeled A through L are columns. All girders have rectangular sections with width 300 mm and depth 600 mm. Slab thickness is 125 mm. Superimposed dead load for the entire floor is 2.95 kPa and live load for the entire floor is 4.8 kPa. For self-weight of the floor system, use unit weight of RC of 23.6 kN/m3. a. Considering continuous girder DEF, determine the maximum factored positive & negative moments Mu (+) & Mu (-), as well as the factored shear Vu that should be used for the design of the said girder. Use ACI moment & shear coefficients to draw the factored shear & moment diagram of the said girder.