The diagram below represents the first two stages of a typical AM receiver. the power gains are Ap1=8 Ap2=0.54 . The input power is Pin =0.34mW 1) Find the overall gain as ratio AT and AT( dB) 2) Find the outputs P, and Pout (unit is mW) 3) Express P1 and Pout in dBm P1 amplifier Ap1 Pin Mixer out Ap2

The diagram below represents the first two stages of a typical AM receiver. the power gains are Ap1=8 Ap2=0.54 . The input power is Pin =0.34mW 1) Find the overall gain as ratio AT and AT( dB) 2) Find the outputs P, and Pout (unit is mW) 3) Express P1 and Pout in dBm P1 amplifier Ap1 Pin Mixer out Ap2

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Q2 (A) A frequency modulator is supplied with a carrier at frequency fc = 5 MHz and an audio tone signal of Am = 1 volt amplitude and frequency fm = 1 kHz. It produces a frequency deviation f of 10 kHz as the output of the frequency modulator. (3)(i) The FM waveform described above is passed through a frequency multiplier with a total multiplication factor of 18, that is, fout = 18*fc. After passing through the frequency multiplier, what is the frequency deviation f at the output?(ii) The output of the multiplier in part (a) is next input to a mixer stage with the LO oscillator frequency set at fLO = 55 MHz. Find the sum-frequency output fo of the mixer’s IF port and also find the magnitude of the frequency deviation f.
a. In AC, how are the capacitors treated? b. In AC, how are DC sources treated? c. What is the amplifier configuration of Figure 4? d. What is the expected phase shift of the sinusoidal input at the output side? e. What is Zi across RG, the gate resistor? f. It is the IC in its smallest form. g. The most commonly used metal as interconnect of the chip to external peipheral. h. How is pin 1 of the chip determined? i. An IC package similar to a DIP but with the pins bent outward. j. Which sensors are packed as IC?
Find the voltage attenuation ratio for a 30 dB attenuator. Show detailed calculation pls.
12-14. For a QPSK system with the parameters mentioned below, determine:(a) Carrier power, in dBm.(b) Noise power, in dBm.(c) Noise power density, in dBm.(d) Energy per bit, in dBJ.(e) Carrier to noise power ratio.(f) Eb/N0 ratio. C= 10^(-13w)fb= 30 kbpsN= 0.06x10^(-15W) B = 60kHz
C ompare the amplitude modullation and frequency modulations. What arethe advantages and disadvantages of both systems? (Please original answer not copy from internet)
Express the voltage, current, and power gains ,a signalvi = 0.1 sin 2000πt volts Thévenin equivalent source resistance RI of 2 kΩ, and we ’d like to listen to that signal with a 32-Ω ear bud, represented by the load RL , as depicted by the circuit model in dB.
1. For an electronic device operating at a temperature of 17°C with a bandwidth of 10 kHz, determine:a. ThermalnoisepowerinwattsanddBm.b. Rmsnoisevoltagefora100Ωinternalresistance. 2. Two resistors, 20 kΩ and 50 kΩ are at ambient temperature. Calculate for a bandwidth equal to 100 kHz, the thermal noise voltage for the tworesistors connected in parallel.
Determine the output voltage value of a transistor amplifier circuit by frequency for 1.923 V to input voltage. Instead of. Calculate the gain in dB for the frequency given in the table. Maximum write down the frequency (s) where the gain is halved in terms of power (3dB). Frequency curve draw as
a. An AM transmitter has the unmodulated carrier power of 20kW and can be modulated to a maximum of 70% before the system saturates/overloads. Find the value to which carrier power can be increased if 40% modulation limit is imposed.b. An analog communication system using FM has the highest modulating frequency of 5 kHz and maximum deviation of 25 kHz. Calculate the bandwidth of modulated signal using Carson’s rule. Compare this value with the one obtained using the simple formula. For practical systems which of these values should be used?
What is the conversion gain (for n = 1) for the doubly balanced mixer as shown if IBB = 5 mA, RC = 1 kΩ, and 2 R1 = 200 Ω. What is the largest value of Vm that satsifies our small-signal assumption?
Q1-The message signal m(t) into a FM modulator with the parameter kf=25 is shown in the following figure. a) Express the FM signal in time domain.b) Calculate and plot the frequency deviation in Hz.c) Calculate and plot the phase deviation in radians.
Question is attached a) Find an expression for Vout/Vs (i.e. voltage gain from signal to load) using given parameters Rs, Rin, Rout, RL and Kv. (Hint: You can use Vout/Vs = (Vout/Vin) ×(Vin/Vs))b) Let’s say Rs = 10kΩ, Rin = 1kΩ, Rout = 100kΩ, RL = 100Ω, Kv = 100. Find Vout/Vs. Assume that we are not able to change Rs, RL and Kv. How can we achieve higher Vout/Vs? Discuss whether large or small resistors values are desirable for Rin and Rout in order to obtain high voltage gain from signal to load? Explain based on your expression from part a).