The diameter of a solid shaft is D. The inside and outside diameters of a hollow shaft of same material and length are 2D and 3 respectively. What is the ratio of the weight of the hollow shaft to that of the solid shaft? What is the strain energy stored in a cantilever beam of length L when acted upon by a point load P at its free end?

The diameter of a solid shaft is D. The inside and outside diameters of a hollow shaft of same material and length are 2D and 3 respectively. What is the ratio of the weight of the hollow shaft to that of the solid shaft? What is the strain energy stored in a cantilever beam of length L when acted upon by a point load P at its free end?

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

with a certain machine, the applied force moves 3.3 m to raise a load of 8 cm. Find the a) IMA and b) AMA if the efficiency is 60 percent. What load can be lifted by an applied force of 50 N if the efficiency is c) 100 percent and d) 60 percent?
A solid green bar with d = 62 mm is plced inside a hollow blue bar with external diameter D = 103 mm. If they carry a torque T = 134 kN-m and the length L = 9 m, what is the ratio of the torque of the solid to the hollow bar? (no unit) Gsolid = 170 GPa. Ghollow = 200 GPa
A steel bar which is fixed at the ceiling , carries an ore bucket of weight W hanging at its end. Neglect the weight of the bar.Given : Bardia = 12mmLength = 18m E = 200 DPa. Calculate the weight that can be safely carried so as not to exceed the allowable steel tensile stress of 138 MPa . In kN
The homogenous semicylinder has a mass of 20 kg and mass center at G. If force P is applied at the edge, and r = 300 mm, determine the angle θ at which the semicylinder is on the verge of slipping. The coefficient of static friction between the plane and the cylinder is μs = 0.3. Also, what isthe corresponding force P for this case?
Convert: (a) 200 lb-ft to N-m, (b) 350 lb/ft3 to kN/m3, (c) 18 ft/h to mm/s.
A rod of diameter 50 cm and length 6 m is hanging vertically and carries an axial loadof 10 kN at bottom end. Calculate the elongation of the bar at a distance 2 m from thebottom end. Take the unit weight of the rod material is 25 kN/m' and modulus ofelasticity of the material is 3x109 MPa.
A column having length 5 m is subjected to a buckling load of 2.5 kN. What will be the diameter of the column, if one end of the olumn is fixed and the other end free? Take E = 200 Gpa
Qs.The strength of the longitudinal joint is 25 kips/ft, whereas for the girth joint it is 20 kips/ft. Calculate the maximum diameter of the cylindrical tank if the internal pressure is 110 psi. Also discuss the joint strength and diameter of tank requirement for the given conditions .If you dont know the answer please skip and let others do , dont post wrong answer, dont waste qsn
A 900 N-m couple is applied to the flywheel in the diagram. The minimum force X required to prevent rotation of the flywheel is also applied. If the coefficient of belt friction is 0.20, a. which tension is larger, TA or TB?Explain b. What is the angle of contact in radians? c. What is the value of the ratio TA/TB?
A wire 4m long is stretched horizontally between points A and B 4m apart. A load W placed at the center of the wire produces a sag of 53.4mm,a. If the wire is 25mm2in cross-section and the Young’s modulus is 200GPa, what is the magnitude of load W?b. If the load was reduced by 40%, what will be the sag?
Hi, I need help with this question please. Thank you. A cantilever thin-walled cylindrical tube of inner diameter ? = 30cm and thickness ? = 1cm is subjected to a torque T and internal pressure p as shown below. The free end of the tube is closed. Strain gauges A and B mounted on the surface of the cylinder give readings ?? = 7.5 × 10^−6 and ?b = 19.7x10^−6, respectively. The bar is made of steel having Young's modulus E=200 GPa and Poisson's ration ? = 0.3. a) Determine the torque, T, and internal pressure, p. b) Determine the absolute maximum shear strain ???? at point C.
Compute the midspan value of EIy for the beam loaded as shown.