The diameter of the large piston of a hydraulic jack is found to be 75 mm. A force of 58 N is applied on the small piston. If the load lifted by the large piston is 0.0906 kN. What will be the diameter of the small piston in millimetres?

The diameter of the large piston of a hydraulic jack is found to be 75 mm. A force of 58 N is applied on the small piston. If the load lifted by the large piston is 0.0906 kN. What will be the diameter of the small piston in millimetres?

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter7: Dry Friction

Section: Chapter Questions

Problem 7.73P: The normal pressure acting on the disk of the sander is given by p=(4/3)+(r2/6), where p is the...

See similar textbooks

Related questions

Q: 1) The OABCDE plate which has a weight of 300 N is hanged with three cables as shown. Find the cable…

Q: A 2.0m long bar is being used as a first-class lever. It has a load of 720 N placed on one end…

Q: What would be the maximum weight W of the block shown in the following figure, so that the tension…

Q: Q2/ A former student of mechanics wishes to weigh himself but has access only to a scale A with…

Q: If P is to be 400 N. What is the value of the weight W? В A

Q: Determine the force in each cable if F = 500 lb. Ans: FAC = 113 lb FAB = 257 lb FAD = 210 lb %3D 1ft…

A: Given: The magnitude of force, F = 500 lb Solution: The force F is acting in z direction. There are…

Q: With what force magnitude T must the person pull on the cable in order to cause the scale A to read…

Q: Q1) Find the force F on the bottom of the tank if: K=1.5 m, H= 6 m, D=5 m. Air Oil Mercury s.g=0.9

A: Given data: k = 1.5 m H = 6 m D = 5 m S.G = 0.9 Need to determine the force at the bottom tank.

Q: Q1: Determine the magnitude of the force on the pin at A for the boom shown in Fig. 1. Neglect the…

Q: The cords ABC & BD can each support a maximum load of 274 lb. D. 1213 What is the maximum weight of…

Q: With what force magnitudeT must the person pull on the cable in order to cause the scale A to read (…

A: Vector is a physical quantity that has magnitude and direction both. Scalar is a physical quantity…

Q: What would be the maximum weight W of the block, shown in the following figure, so that the tension…

Q: Q2/ A former student of mechanics wishes to weigh himself but has access only to a scale A with…

A: Solution: The scale A shows only an apparent reading of 67lb. Since the man pulls the string with a…

Q: Three pairs of flexible cables, spaced at 120° inter- vals, are used to stabilize a 1000-ft…

A: Draw free body diagram of cable AC

Q: Question continued... (where the force P1 is equal to 259 lb and the force P2 is equal .to 88 Ib) P1…

A: Given, P1=259 lb,P2=88 lb

Q: The small piston of a hydraulic lift has a cross-sectional area of 4.6 cm2 and its large piston…

A: Given Data⇒cross-sectional area of smaller sectionA1=4.6 cm2=0.00046 m2cross-sectional area of…

Q: Given the image below, what is the magnitude of the equivalent concentrated load of the weight of…

Q: In the Figure 3, if the m=15 kg and 0=30°, then the weight component of the block parallel to the…

A: Given data : Mass of object m=15 kg Acceleration due to gravity g=9.81 m/s2 Angle θ=30∘

Q: An old man lift's a load by applying a force of 134 N to a hydraulic piston of area(A1) 0.02 m². If…

Q: The small piston of a hydraulic lift has a cross sectional area of 3.00cm^2 and its large piston had…

Q: A 1000 Ibs TTTTT t A horizontal cable exerts a force of 399.971 pounds while holding a boom into…

Q: Abbot and Costello are transporting a 0.125m3 cubic block along a ramp inclined at 20°. They tied…

A: Given: Volume of cube is 0.125 m3. Mass of the pole arm is 2 kg. Length of the pole arm is 3 m.…

Q: Q3- The crate has a weight of 500N shown in Fig (3). Determine the force in each supporting cable.…

Q: What is the normal force between the crate and the wedge? What is the smallest force P needed to…

Q: The Diameters of a small piston and a large piston of a hydraulic jack are 5 cm ad 10 cm…

Q: 1C. The given system of knotted cords (label the left knot as J and the right knot as K) supports…

Q: Cords are looped around a small spacer separating two cylinder each weighing 400kn and pass over a…

Q: A cylinder suspended by a rope rests against an inclined surface as shown. If the cylinder weighs…

Q: A 392-N force parallel to the plane is required to support a body on an inclined plane, of height…

A: Given data: Support force applied to the body, P = 392 N. Normal force acting on the body, N = 780…

Q: Determine the value of force P (in N).

A: To determine the value of Force

Q: The pulley system below is in static equilibrium, where load W3 is 730 N, angle α = 50O and angle θ…

A: Given Data The given load is:W3=730 N θ=30° α=50° To find: The ratio of the load W1W2 Now draw the…

Q: Q/ The force in the member (CA) is 50 kg 12m 5m BY

Q: The boom of the wall crane 4m long is held at right angles to the wall by a wire that is attached to…

Q: the frame Shown in fiqure find the force in each member under the given toading: lom 5m 1OUKN 5m…

A: given data: T=tention on different rod

Q: The first step to determine the amount of force T is;

A: Free Body diagram . Whenever we deal with the problem of mechanics ,most of the problem's first step…

Q: A pole is supported by a wire which exerts a pull of 200 lb on top of the pole. If the angle between…

A: Horizontal component,FH=200Sin(50°)=153.21lb Vertical component,Fv=200Cos(50°)=128.56lb

Q: 1 ft 1 ft 2 ft Consider the given frame. В a) Determine the magnitude of the vertical reaction (Ib)…

A: Let CODE A lb=W lb Draw the overall free body diagram of the frame:

Q: A 90 degrees angle on a 1/2 inch water pvc pipe. determine the force on the angled pipe if the water…

A: Given data: The bent angle of the pipe is θ=90°. The diameter of the pipe is D = 1/2 in. The water…

Q: The small piston of a hydraulic press has a cross-sectional area of 3cm2, and its larger piston has…

A: Given data: The cross sectional area of small piston, A1 = 3 cm2. The cross sectional area of large…

Q: Determine the horizontal force P required to start moving the M-kN block, shown in figure (5), up…

Q: Q16 Find the force needed by man to raise the load if distance of load 2m and the man force distance…

Q: A 200# stone is being lifted off the ground by a levering bar. Determine the push P required to keep…

Q: final Consider ACB as two segments (AC & CB) and 5ft each have a weight of 14 lb. If part DE is…

A: Giventwo segments AC and CBeach have a weight of w=14lb

Q: The Cylinder weighs 1000 kg, rest on an plane which is inclined at 34° from the horizontal. The…

Q: "STATICS" HOME WORK (2) Q1: The machine part of negligible weight is supported by a pin at A and a…

A: Find the reactions at point A and C.

Q: A man holds a 35-kg ladder in his hands perpendicular to his hands (Figure 6). The free body diagram…

A: Given data: m=35 kgF=400 N Need to determine the minimum value of θ so that the person is able to…

Q: 2 A truss is loaded with various forces of magnitudes as shown in Fig. 2. Determine the forces in…

A: To find force in member DE,DJ,EJ,IJ

Q: The forklift supports the engine. Determine the force that this load generates on element FB. Write…

A: A moment is a movement of the body when a body is rotating on an axis. The moment is also known as…

Concept explainers

Basic Terminology in Mechanics

The area of science and mathematics concerned the motion of the objects, the relation between the force matter, and motion if specified. Forces exerted over the objects result in displacements or changes in the position of an object concerning its environment. This branch of physics keeps its roots in Ancient Greece in the form of the scripts of Aristotle and Archimedes.

Question

100%

The diameter of the large piston of a hydraulic jack is found to be 75 mm. A force of 58 N is applied on the small piston. If the load lifted by the large piston is 0.0906 kN. What will be the diameter of the small piston in
millimetres?

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

The 50-ft measuring tape weighs 2.4 lb. Compute the span L of the tape to four significant figures.
The thin-walled cylindrical can with a spherical dimple weighs 0.2 lb. Determine the force P required to push the can into water to a depth of 8 in. Use =0.036lb/in.3 for water.
The normal pressure acting on the disk of the sander is given by p=(4/3)+(r2/6), where p is the pressure in pounds per square inch (psi) and r represents the radial distance in inches. Determine the torque C required to operate the sander at constant speed if the kinetic coefficient of friction for the surface being sanded is 0.86.
Neglect the thickness of the bar. Take ua=ub=u suppose that b= 1 ft
Calculate the required pressure that must be applied on petrol with a density of 700 kg/m3in order to increase its density to 702 kg/m3if its elasticity is 1.4 GPa
.A flywheel rim has a mean diameter of 500 mm and weight 120 kg. The density of the flywheel material is 7200 kg/m3. Which of the following is the thickness of the flywheel if the rim width is twice its thickness? choices: 146 mm 103 mm 52 mm 73 mm
A lever is used to lift a heavy load. When a 25 N force pushes one end of the lever down 1.8 m, the load rises 0.3 m. a) Determine the Mechanical advantage of the lever. b) Calculate the weight of the load.
The Diameters of a small piston and a large piston of a hydraulic jack are 10 cm and 20 cm respectively. A force of 100 KN is applied on the small piston. Find the load lifted by the large piston when the pistons are at the same level.
Each pulley has a weight of 10 lb. (Figure 1) If each cord can support a maximum tension of 600 lblb determine the largest weight that can be supported by the pulley system. Express your answer in pounds to three significant figures.
The figure below illustrates a hydraulic jack.a) Calculate the force F1 exerted by the operator to lift a load F2 of 104N, knowing that the diameter of the pump piston is 6 mm while the diameter of the load cylinder is equal to 25 mm. Answer: 576 N b) Determine the diameter of the load cylinder so that the force F1 is equal to 100 N. Answer: 0.06m
Abbot and Costello are transporting a 0.125m3 cubic block along a ramp inclined at 20°. They tied the block under the midpoint of a 3m, 2kg, pole-arm. Abbot is at the lower end of the pole while Costello leads the pair up, holding the other end of the pole. Calculate the upward forces exerted by Abbot and Costello during the transport if the block weighs 1000N.
Show complete solutions and figures The diameters of the two cylinders A and B in the figure shown are 80 mm and 750 mm, respectively. The face of the piston is 1.2 m above the face of the weight platform. The space in between the piston and the weight is filled with oil (s.g.=0.80). If F=75 N, Determine the following: the value of Wrequired to maintain equilibrium. a) 38.6 N b) 86.3 N c) 63.8N d) 83.6 N e) None