The difference between the moments of Inertia of area A with respect to the x1 and x axes is 0.365m^4. (Ix1-Ix=0.365)Calculate the area, knowing that A has its CG at C.P=17 The difference between the moments of Inertia of area A with respect to the x1 and x axes is0.365m*. (lx1-lx=0.365)Calculate the area, knowing that A has its CG at C.P=170,1*P = 170,4mx1Area =

Answered: Image /qna-images/answer/8faaf6b6-f3b9-4b90-871b-1a746b1d9dfa.jpg

Answered: The difference between the moments of…

The difference between the moments of Inertia of area A with respect to the x1 and x axes is 0.365m^4. (Ix1-Ix=0.365) Calculate the area, knowing that A has its CG at C. P=17

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter9: Moments And Products Of Inertia Of Areas

Section: Chapter Questions

Problem 9.36P: Determine the product of inertia with respect to the x- and y-axes for the quarter circular, thin...

See similar textbooks

Related questions

Q: The piston of the hydraulic cylinder gives pin A a constant velocity v = 3.1 ft/sec in the direction…

Q: Discuss .maintenance aspects of a typical industrial control valve.

A: Given question: Discuss maintenance aspects of a typical industrial control valve.

Q: Q4/ See Fig. (4). What force P must the two men exert on the rope to slide the uniform 6 m beam of…

Q: The extruded plastic shape has dimensions of D = 24 mm, d = 20 mm, a = 87 mm, and t = 6 mm. (a)…

Q: f the distance between the points A and B is 2 meters and the angular velocity of the body is 5…

Q: 2) The pillow block shown in Figure 2 is attached to the fixed plate by using two M20x1.5 ISO class…

A: Introduction: A factor of safety factor is an engineering phrase that describes how much stronger a…

Q: 10. The metal iridium has an FCC crystal structure. If the angle of diffraction for the (220) set of…

Q: The velocity of a particle which moves along the s-axis is given by s˙s˙ = 30 - 5t2 m/s where t is…

A: Introduction: We utilize the basic concepts of speed and velocity to describe the motion of objects…

Q: Pipes 1 2 W|N 3 Length 8,000 ft 2,000 ft 3,000 ft

A: Given as,

Q: For a current carrying wire of 40 mm diameter exposed to air (h=30W/m2K), maximum heat dissipation…

Q: Determine the theta, 0, angle for the first order reflection (n = 1) from these {111} planes if the…

Q: A gas turbine power plant operating on Brayton cycle shown in figure. The air enters the compressor…

A: For the Brayton cycle, r = compression ratio of the compressor = 7 T1 = 300 oCT2 = 700 oC P3 = 600…

Q: Q6: A balloon behaves so the pressure is P = CV, C = 100 kPa/m. The balloon is blown up with air…

Q: A particle moving in the x-y plane has a position vector given by r = 0.60t²i + 1.41t³j, where r is…

Q: An oil pump operating at steady state delivers oil at a rate of 12 lb/s through a 1-in.-diameter…

A: All pumps use the fundamental forces of nature to move a liquid. Once the moving pump element…

Q: (B):-During corrosion tests, current density of 0.86 Amp/m² was measured for steel sample immersed…

Q: A car is traveling around a circular track of 630-ft radius. If the magnitude of its total…

Q: Replace the loading system acts on beam shown in Fig. (3) by an equivalent system consists (Single…

A: Given

Q: Maximize subject to P = 30x1 + 40x2 2x1 + x₂ ≤ 10 x1 + x₂ ≤7 x1 + 2x2 < 12 X1, X20

Q: estion 36 There is _______ three-dimensional crystal structures?

A: given = fill in the blank

Q: A venturi meter is introduced in a 300 mm diameter horizontal pipeline carrying a liquid under a…

Q: determine the centroid of the built up section in figure 1. Express the coordinates of the centroid…

A: Draw the given diagram with sections.

Q: A graduate student wants to use van der Waals' equation to express the pressure-volume- temperature…

A: Write the expression of van der Waals' equation. P+aV2V-b=RT

Q: NCLUDE DETAILED CALCULATION AND EXPLANATION Suppose you are a group of cadet engineers given by…

A: A flow metre is a tool that gauges a fluid's flow rate. The linear, nonlinear, mass, or volumetric…

Q: 1. A cold drawn mild steel, AISI 1018CD is used to fabricate the hollow shaft as shown in Figure Q1.…

Q: Q4:-A shock wave is moving down a constant area duct containing air. The air ahead of the shock wave…

Q: Q3: Explain how you would produce a hard surface in the followings, Give reason(s) for your…

A: Given question: Q3. Explain how you would produce a hard surface in the following. Give reason for…

Q: Explain why an absolute temperature is defined and give its SI units.

A: Given Data : Absolute temperature SI Unit

Q: Q3: Explain how you would produce a hard surface in the followings, Give reason(s) for your…

A: Given question: Q3. Explain how you would produce a hard surface in the following, Give reason for…

Q: Q1:A/Solve the following linear programming problem using the graphical method Min (Z)= 20X+30Y…

A: Minimize Z = 20X + 30Y Subjected to X + 2Y ≥ 6 4X + 2Y ≥ 12 6X + 2Y ≥ 15 X ≥ 0, Y ≥ 0 X + 2Y ≥ 6…

Q: (a) Determine the reactions at A and E if P = 840 N. The reactions are positive if to the right or…

Q: b) A machine is installed on the first floor of a building, which can be modeled as a rigid…

A: Given question: Identify and design the vibration control measures required to reduce the…

Q: 2. A stone is thrown with an initial velocity of 100 m/sec upward at 60⁰ with the horizontal,…

Q: 5. A compound bar containing bronze and steel segments carries the axial loads as shown in Figure…

Q: QI two forces shown determine the effect of these two force. cusing Parallelogram method) acts on…

Q: Reduce the forces acting on the beam to a single resultant force and determine its point of…

Q: force on the pin from the slot, respectively, are

A: Given. Section modulus of the member is same in both the arms.where, An L shaped elastic member ABC…

Q: The figure below shows a frustum of a cone with an orifice in the bottom of 2,000 cm² area. Assume C…

A: Solution Given data- C = 1.0 a = 2000 cm2 = 0.2 m2

Q: 5. The arms of a Porter governor are 300 mm long. The upper arms are pivoted on the axis of rotation…

A: Introduction: The two balls of a porter governor are pivoted at the top to allow for vertical…

Q: 3. Derive the equation of motion and find the steady-state response of the system depicted in the…

Q: I need the answer as soon as possible

Q: Q2: Find the solution to the following linear programming problem using the Graphical method Max…

Q: The bar is made from welding two uniform 40 lb bars together. Calculate the magnitude of the pin…

Q: 12. Calculate Discharge through a horizontal Venturi meter for following given data: Diameter of…

A: Introduction: A venturi meter is a device in which pressure energy is converted into kinetic energy…

Q: A bolt thread is designated as M 20 x 1.5 with core diameter equal to 18.16 mm. If 20 kN tensile…

A: ◆ The shear stress across the thread is 7.96 MPa. ◆ Therefore, the correct answer is option (d).

Q: The force of attraction between 2 particles of masses 250 kilograms and 50 kilograms respectively is…

A: Given that: m1 = 250 kg, m2 = 50 kg Force of attraction between m1 and m2 = 1.723*10-13 N G =…

Q: Q6: A balloon behaves so the pressure is P = CV, C = 100 kPa/m. The balloon is blown up with air…

Q: Air at 3000 R and 200 psi expands isentropically to 50 psi. What are the enthaly change and new…

A: Introduction: An isothermal process occurs at a fixed temperature, but other system parameters can…

Q: 848 kJ/kg, 1.498 kg/m³. Steam leaves at P2 = 2996 kPa Heat loss from the = 2. Steam enters a turbine…

Concept explainers

Moment of Inertia

Inertia can be termed as a resistance offered by a body to change its state. A rigid body initially at rest will apply resistance when acted by an external force that tends to change its state of rest or velocity, or a body initially at motion will provide resistance in changing its state of velocity or motion for coming to a state of rest. In other words, Newton's first law of motion describes the law of inertia of a rigid body.

Question

The difference between the moments of Inertia of area A with respect to the x1 and x axes is 0.365m^4. (Ix1-Ix=0.365)
Calculate the area, knowing that A has its CG at C.

P=17

The difference between the moments of Inertia of area A with respect to the x1 and x axes is
0.365m*. (lx1-lx=0.365)
Calculate the area, knowing that A has its CG at C.
P=17
0,1*P = 17
0,4m
x1
Area =

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Determine the product of inertia with respect to the x- and y-axes for the quarter circular, thin ring (tR) by integration.
The shaded area has the following properties: Ix=1.26x10^6 mm^4, Iy=6.55x10^5 mm^4, Pxy=-1.02x10^5 mm^4 Determine the maximum moment of inertia and the minimum moment of inertia
The difference between the moments of Inertia of area A with respect to the x1 and x axes is 0.365m^4. (Ix1-Ix=0.365)Calculate the area, knowing that A has its CG at C. P=27
Find the Moment of Inertia of the plate as shown in figure, passing through its centroid with reference to Y -Y axis. Where b1 = 55 mm, d1=110 mm, b2=160 mm, d2=30 mm, b3=65mm, d3=24mm. The value of is (unit in mm) = ______________ Answer for part 1 The value of is (unit in mm) = ______________ Answer for part 2 The value of total for the given plate is (unit in mm4) =________________ Answer for part 3
Determine the moment of inertia of the homogenous triangular prism with respect to the y axis. Hint: For integration, use thin plate elements parallel to the x-y plane having a thickness of dz. Express your answer in terms of the variables a, b, h, and m.
The shaded area has the following properties: Ix=1.26x10^6 mm^4, Iy=6.55x10^5 mm^4, Pxy=-1.02x10^5 mm^4 Determine the moment of inertia about the x' axis if theta =30 degrees and the moments of inertia about the y' axis if theta=30 degrees
Determine the moment of inertia of mass with respect to the x' axis that passes through the structure's center of gravity and is parallel to the x axis. The cone has a density of 6000 kg/m3 and the cylinder a density of 8000 kg/m3. Consider H = 83
Select the correct S I units for the Moment of Inertia for an area. m3 m4 kg m2 kg m3
The moment of inertia of a rectangular plate of width ‘b’ and height ‘d’ about Y - Y axis passing through its center of gravity is Select one: bh3/12 bd3/12 db3/12 dh3/36
Determine the moments of inertia and the product of inertia of the L127 x 76 x 12.7-mm angle cross section with respect to new centroidal axes obtained by rotating the x and y axes 45° counter clockwise.
Determine the product of inertia of the thin strip of area with respect to the x and y axes. The strip is oriented at an angle θ from the x axis. Assume that t<<l Express your answer in terms of the variables l,t and θ < (IMPORTANT)
The moments of inertia about the x- and u-axes of the plane region areIx = 14 × 10^9 mm^4 and Iu = 38 × 10^9 mm^4, respectively. If h = 200 mm, determine the area of the region, and the radius of gyration about the centroidal axis parallel to the x-axis.