Answered: The distance y from the back of the…

Engineering

Mechanical Engineering

The distance y from the back of the shorter leg to the neutral axis XX is

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter9: Moments And Products Of Inertia Of Areas

Section: Chapter Questions

Problem 9.13P: Figure (a) shows the cross section of a column that uses a structural shape known as W867...

See similar textbooks

Related questions

Q: the given two views shown in Fig. below draw the isometric projection use scale1:1 110- -08- 15 R25 ...

Q: If the cross-section areas of the smaller and larger pistons are 0.002 m2 and 0.2 m2 respectively an...

Q: Just for checking determine if true or false 1.) Tensile force tends to cut the body in two. 2.) F...

A: given; 1.) Tensile force tends to cut the body in two. 2.) FBD is a sketch of the isolated body whic...

Q: The propeller shaft of a large ship has outside diameter 18 in. and inside diameter 12 in., as shown...

Q: A rope 3.5 mm? breaks when a load of 50 kN is applied to it. Estimate the diameter of the same rope ...

Q: A tri metallic bar is uniformly compressed by an axial force P=12kN applied through a rigid end plat...

A: Given data: Axial force = 12 kN = 12000 NSteel core diameter = 10 mmBrass tube inner diameter = 10mm...

Q: value of

A: introduction: here we have to find the dependency of spring constant on gravity

Q: PROBLEM 1: Seventy kilojoules of work is done by each kilogram of fluid passing through an apparatus...

Q: 2. The two 200-lb blocks are pushed apart by the 15° wedge of negligible weight. The angle of static...

A: Answer: The force P required to start the blocks moving is 48.6 lb.

Q: acceleration of the crate sliding down a ramp is given by Ax= (0.25t²) m/s² and Ay= (1.5t³) m/s², wh...

Q: List three sources of error that would account for the differences between your values and the accep...

A: given; List three sources of error that would account for the differences between your values and th...

Q: A piston-cylinder contains 2.1 kg of air at T1 = 800 K and P1 = 848 kPa. The air is brought to a fin...

Q: 9) Which one of the following helps in the reduction of NOx in a catalytic converter? O Platinum O P...

A: We will answer the first question since the exact one was not specified. please submit a new questio...

Q: Draw a scale when 2m is equal to 5cm then show a distance of 4.02m and 2m 6dm 9cm on this scale.

A: Given 2m for 5 cm To find 4.02 m 2 m 6 dm 9 cm

Q: A belt conveyor transports 18 tonnes per hr at 20°. Calculate the total length to be sufficient to g...

A: V-belt pulleys (likewise called vee belt bundles) are gadgets which send power between axles by the ...

Q: . What is the approximate reaction moment at the fixed support A for the loaded frame shown below? (...

Q: Explain why oil circuit diagrams are invaluabletools for diagnosing a transmission problem.

A: When the computer system sends inaccurate signals as a result of a defective sensor, one of the ...

Q: The block in the figure slides in the slot in the fixed piece 1. Axis Q2 of crank Q2A is fixed on 1....

A: Since you have asked multiple sub parts, we will solve first three sub parts for you. to get remain...

Q: 2.0 Liquid ammonia at a temperature of 26 °C is available at the expansion valve. The temperature of...

Q: 1. A shaft made of steel having an ultimate strength of Su is finished by grinding the surface. The ...

Q: Derive the formula used in determining experimental hydrostatic force using the center of pressure a...

Q: Determine the forces in members BC, CF, and EF of the stairs truss shown in Figure 5.State whether t...

Q: Determine the coefficient of restitution e between ball A and ball B. The velocities of A and B befo...

Q: 1.0 A mass of ice at -7 °C is needed to cool 124 kg of vegetables (Cp = 3.35 KJ /kg.K )in a bunker f...

A: The required mass of ice is 23.087 kg.

Q: The five-bolt connection must support an applied load of P = 3800 lb. If the average shear stress in...

Q: 2. A 1-m' rigid volume contains water at 90°C with a quality of 0.B. Determine the final temperature...

Q: 1. The working substance for a Carnot cycle is 8 lb of air. The volume at the beginning of isotherma...

Q: A tie is used to suspend an object, which is later completely immersed in a bowl of water. object ha...

A: My answer does not match with the given options but my solution is correct for sure and this will be...

Q: A single-acting cylinder of 25 mm diameter is to clamp a component when a push button is pressed. As...

A: A single-acting cylinder of 25 mm diameter is to clamp a component when a push button is pressed. As...

Q: 2. (a) Bring out the advantages and disadvantages of using a hydraulic system with a suitable applic...

A: Hydraulic system make use of liquids usually hydraulic oil to convert fluid pressure into useful wor...

Q: With appropriate precision (significant digits), what is 2 + 2.1?.

A: It is required to determine 2+2.1

Q: ) the volumetric flow rate, Q, in each exit branch in units of L/s ) the velocity, V, in each exit b...

Q: With 3% moisture, 2.5 kg of wet steam has an enthalpy of 6600kj. It is heated at constant pressure t...

Q: Please answer in essay: From the figure below, discuss the internal effect of the external forces ...

A: EXTERNAL AND INTERNAL FORCES External forces are powers brought about by outside specialist outside ...

Q: A bearing supports a 28mm diameter solid steel torsion rod (plan view shown in Fig. 1) rigidly comme...

A: Given Datad=28mmarm=300mvertical load =2500N

Q: Figure 9.14 shows a heat exchanger in which each of two DN 150 Schedule 40 pipes carries 450 L/min o...

A: Given : DN 150 Schedule 40 pipes Q = 450L/min To find : Velocity in pipe Flow rate required in duct

Q: Q1. A rectangular gate is hinged at the water line, as shown. ) Draw a FBD of the gate, complete wit...

Q: ꜱᴏʟɪᴅ ᴀʟᴜᴍɪɴᴜᴍ ꜱʜᴀꜰᴛ ᴏꜰ 98 ᴍᴍ ᴅɪᴀᴍᴇᴛᴇʀ ꜰɪᴛꜱ ᴄᴏɴᴄᴇɴᴛʀɪᴄᴀʟʟʏ ɪɴ ᴀ ʜᴏʟʟᴏᴡ ꜱᴛᴇᴇʟ ᴛᴜʙᴇ. ᴅᴇᴛᴇʀᴍɪɴᴇ ᴛʜᴇ ᴍɪɴ...

A: Given:d=98 mmF=547 kNμ=13E=75 GPa

Q: Starting from rest, Block A moves down the inclined plane with velocity given by 3t“, where t is in ...

Q: Member AB (helical spring) and Member AC (axial rod) are carrying a weight at point A. Member AB has...

Q: Question 1 In the strength of material, the section of the body involved is taken into consideratio...

A: 1) Given that an object is having a force which has a cross section area. Then by the definition - ...

Q: A steel shaft 2542 mm long must transmit a torque of 34 KN-m. The total angle of twist and the maxim...

Q: The force exerted by the motor M on the cable is shown in the graph. (Figure 1) Part A: Determine th...

A: Given data: w=155 lbt=2.5 s Need to determine the velocity of the crate A at t=2.5 sec.

Q: PROBLEM 1 A hydroelectric power plant has the hydraulic turbine located 60 m below the elevation of ...

Q: Find the rertical if Pis 20KN movement of P Steel Aluminum 4m 2m Im B

Q: 14.5 Find the cylinder dimension of a single-cylinder, double acting compressor handling 28.32 Its/r...

Q: You may have noticed that bridge decks are often built with expansion joints that permit the deck to...

A: To full fill the quality parameters , we can not provide hand written solution Givenα=12.3×10-3Tmin...

Q: 2.0 Liquid ammonia at a temperature of 26 °C is available at the expansion valve . The temperature o...

A: (A) Here we have h3=h4=303.6 kJ/kgh4=hf+xhfg

Q: 12x+1 dr VAx-3

A: According to the details provided in the question, we need to calculate integration. According to ...

Q: Discuss what is the most mechanized and least mechanized operation in rice productions in Philippine...

A: Mechanization of rice production helps to incorporate the use of machinery to reduce the effort put ...

Concept explainers

Slope and Deflection

The slope in a deflected beam is described as an angle in radians made by the tangent of the section with the original axis of the beam. The deflection at any point on the axis of the beam is defined as the lateral displacement of the point before and after loading.

Question

An L-shaped section has the following dimensions:

The length of the longer leg is 5 in, the length of the shorter leg is 31/2., and the thickness of each leg is 3/8 in. The distance y from the back of the shorter leg to the neutral axis XX is

A. 1.76 in

B. 1.98 in

C.1.53 in

D. 1.61 in

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A tee section is made up of a 30 mm x 150 mm flange and a 30 mm x 160 mm web.4. Which of the following most nearly gives the area of the section in square mm.a. 9000 b. 9300 c. 9500 d. 8700
b)A simply supported beam has a symmetrical rectangular cross-section. If the second moment of area (I) of a beam with a rectangular cross-section is 11.50 x 106 mm4 about its centroidal x-axis and the depth dimension (d) of the rectangular section is 180 mm, determine the breadth dimension (b) for this beam section. Give your answer in millimetres (mm) and to 2 decimal places. Assume the beam section material is homogeneous c) The same rectangular cross-section beam in Q2b is subjected to a maximum bending moment of 25,000 Nm and experiences sagging. Assuming that the centroidal axis passes through the beam section at (d/2), calculate the maximum bending stress (?max) the beam will experience. Give your answer in N/mm2 and to 2 decimal places.
8.5 Determine I, for the thin-walled sections shown in Figures 8.9(a) to 8.9(c), where the wall thicknesses are 0.01 m. NB Dimensions are in metres. second moment of area about a horizontal axis passing through the centroid.
strength of materials 4.) The neutral axis of the given built-up section is nearest to ______ measure from the bottom of the section:
Figure (a) shows the cross section of a column that uses a structural shape known as W867 (wide-flange beam, nominally 8 in. deep, weighing 67 lb/ft). The American Institute of Steel Construction Structural Steel Handbook lists the following cross-sectional properties: A=19.7in.2,Ix=272in.4, and Iy=88.6in.4. Determine the dimensions of the rectangle in Fig. (b) that has the same Ix and Iy as a W867 section.
The properties of the unequal angle section are Ix=80.9in.4,Iy=38.8in.4, and Iu=21.3in.4. Determine Ixy.
A tee section is made up of a 30 mm x 150 mm flange and a 30 mm x 160 mm web.4. Which of the following most nearly gives the area of the section in square mm.a. 9000 b. 9300 c. 9500 d. 8700 5. Which of the following most nearly gives the location of the neutral axis from the bottom of top of the flange.a. 64 mm b. 68 mm c. 51 mm d. 84 mm 6. Which of the following most nearly gives the moment of inertia with respect to the centroidal x-axis in million (1 x 10⁶).a. 21.84 mm⁴ b. 27.45 mm⁴ c. 54.21 mm⁴ d. 31.54 mm⁴
A simply supported beam has a symmetrical rectangular cross-section. If thesecond moment of area (I) of a beam with a rectangular cross-section is 11.50 x 106 mm4 about its centroidal x-axis and the depth dimension (d) of the rectangular section is 180 mm, determine the breadth dimension (b) for this beam section. Give your answer in millimetres (mm) and to 2 decimal places. Assume the beam section material is homogeneous. (show all work)
a) Determine the second moment of area (IXX) about the centroidal x-axis for the solid homogeneous beam section shown below, where the dimensions are b = 5.25 mm and d = 12.75 mm. Give your answer in mm4 to two decimal places. b) Determine the second moment of area (IYY) the about the centroidal y-axis for the solid homogeneous beam section shown below, where the dimensions are b = 5.25 mm and d = 12.75 mm. Give your answer in mm4 to two decimal places.
True or False Tangential Force is the component of the resultant force lying in the plane of the cross section, tending to shear one segment of a body relative to the other.
answer: Xa:0.44 and Xb:0.22 stretch
A block of stone is cut so that its cross‑section is a parallelogram. The width of the bottom side is ?=0.655 m, the height of the top of the block is ℎ=0.915 m, and the top right corner overhangs a distance ?oh=0.195 m from the bottom corner as shown. Assume that the block is of uniform density, so that the center of gravity of the block is located at the geometric center.