The domestic load in residential building is used in the following manner : Fluorescent lamps 55 watt each, 4 Nos. 6 Hrs/day Fans 70 watt each, 4 Nos. 8 Hrs/day Refrigerator of 300 watt, 12 Hrs/day Heater of 1000 watt, 2 Hrs/day Television of 150 watt, 8 Hrs/day Calculate : (i) connected load and (ii) daily load factor (iii) Total cost of electrical energy for 30 days, at the rate of 3/unit

The domestic load in residential building is used in the following manner : Fluorescent lamps 55 watt each, 4 Nos. 6 Hrs/day Fans 70 watt each, 4 Nos. 8 Hrs/day Refrigerator of 300 watt, 12 Hrs/day Heater of 1000 watt, 2 Hrs/day Television of 150 watt, 8 Hrs/day Calculate : (i) connected load and (ii) daily load factor (iii) Total cost of electrical energy for 30 days, at the rate of 3/unit

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.10P: For the circuit element of Problem 2.3, calculate (a) the instantaneous power absorbed, (b) the real...

See similar textbooks

Similar questions

Given a 400sq.m single family dwelling unit to be provided with 230V, 1-phase, 2-wire be service, andhaving the following loads: 2-1.5hp A/C, 2-1.0hp A/C, 1-0.5hp water pump, 4-800W water heater, 2-6kWelectric range and 2-1kW microwave oven, determine a) the total connected load, b) the total demand load,c) the overall %demand factor, d) the size of THW feeder conductor, ground wire and IMC conduit, e) therating of feeder overcurrent protection using inverse time circuit breaker
A single phase wattmeter is used to determine the power taken by a three phase squirrel cage induction motor. The current coils is placed in line 1 while the potential coil is shifted from lines 1 and 2, then from lines 1 and 3 respectively. If the wattmeter registers 5760 and 3380 watts respectively, what is the line current drawn by the motor. Line to line voltage is 230 V.
A 210V, 50 Hz, single phase radial distribution system, the resistance of the wire is 0.0008 ohm/m supply and return. Two loads are connected and it consumes 10 and 10 A respectively and are fed from the cable at distance of 15 and 15 respectively. Calculate the voltage available across load 1 and 2
The yearly load duration curve of a certain power station can be approximated as a straight line ; the maximum and minimum loads being 80 MW and 40 MW respectively. To meet this load, three turbine generator units, two rated at 20 MW each and one at 10 MW are installed. Determine (i) installed capacity (ii) plant factor (iii) kWh output per year (iv) load factor.
The resistance and reactance of the single-phase 60Hz transmission line conductors are 7.6 ohm and 6.6 ohm respectively. The transmission line delivers 20MW at a power factor of 0.66 lagging to the load with 54kV receiving end voltage. Determine the following a) The inductance of the transmission line in mH b) Sending end power factor c) Percentage voltage regulation d) Percentage Efficiency
(1) Given a 400sq.m single family dwelling unit to be provided with 230V, 1-phase, 2-wire service, and having the following loads: 2-1.5hp A/C, 2-1.0hp A/C, 1-0.5hp water pump, 4-800W water heater, 2-6kW electric range and 2-1kW microwave oven, determine the total connected load in volt-ampere (VA). (2) Given a 400sq.m single family dwelling unit to be provided with 230V, 1-phase, 2-wire service, and having the following loads: 2-1.5hp A/C, 2-1.0hp A/C, 1-0.5hp water pump, 4-800W water heater, 2-6kW electric range and 2-1kW microwave oven, determine the rating of feeder overcurrent protection in ampere-trip (AT) using inverse time circuit breaker. Write your answer in numerical format without decimal places
Draw an impedance diagram for the electric power system shown in Fig. Showing all impedances in per unit on a 100-MVA base. Choose 20 kV as the voltage base for generator. The three-phase power and line-line ratings are given below. CO1 G1: 90 MVA, 20 kV, X= 9% G2: 90 MVA, 18 kV, X= 9% T1: 80 MVA, 20/200 kV, X=16% T2: 80 MVA, 200/20 kV, X = 20% Line: 200 kV, X = 120 Ohm Load: 200 kV, S= 48 MW + j64 MVAr
Given a 400sq.m single family dwelling unit to be provided with 230V, 1-phase, 2-wire service, and having the following loads: 2-1.5hp A/C, 2-1.0hp A/C, 1-0.5hp water pump, 4-800W water heater, 2-6kW electric range and 2-1kW microwave oven, determine the total connected load in volt-ampere (VA). Write your answer in numerical format without decimal places.
A 3-phase, 50 Hz, 50 km long overhead line supplies 525 kW at 22 kV, 0.8 p.f. lagging. The line resistance is 3.5 Ω per phase and line inductance is 15 mH per phase. Calculate the Reactance of the Line, Current flowing through the transmission line, Sending end voltage, Voltage regulation and Efficiency of transmission. Inductive Reactance Answer for part 1 Current flowing through the transmission line Answer for part 2 Sending end Voltage Answer for part 3 Voltage Regulation of Transmission line Answer for part 4 Transmission line efficiency
A 3-phase overhead transmission line is being supported by three disc insulators. The potentials across top unit and middle unit are 9 kV and 11 kV respectively. Calculate: a. The ratio of capacitance between pin and earth to the self-capacitance of each unit. b. The line voltage. c. String efficiency. JAns: a. 0.22 b. 35.444 kV c. 76%]
A 3-phase, 60 Hz, 55 km long overhead line supplies 575 kW at 11 kV, 0.9 p.f. lagging. The line resistance is 3.5 Ω per phase and line inductance is 10 mH per phase. Calculate the Reactance of the Line, Current flowing through the transmission line, Sending end voltage, Voltage regulation and Efficiency of transmission. Inductive Reactance= Current flowing through the transmission line= Sending end Voltage= Voltage Regulation of Transmission line= Transmission line efficiency= (please answer all 5 parts)
A short line having an impedance of (2 + j3) ohm interconnects two power stations A and B both operating at 11kV equal in magnitude and phase. To transfer 25 MW at 0.8 power factor lagging from A to B determine the voltage drop must be compensated by the booster so that the voltages are maintain the same at both ends.