The double pipe 1 m length heat exchanger is essentially a set of concentric pipes. One fluid flows within the smaller pipe and the other in the annulus. For such an exchanger (outer diameter of the inside pipe is 2 cm; inner diameter of the outside pipe is 4 cm), water flows in the annular space at an average velocity of 0.2 m/s. The water, which cools an organic flowing in the central pipe, has a temperature change from 16 to 28 . In this case calculate the heat transfer coefficient for the water assuming that the exchanger is heavily insulated and that the wall temperature on the inside of the annulus (outside of central pipe) is 30 . And heat transfer rate=?, heat transfer flux=?

The double pipe 1 m length heat exchanger is essentially a set of concentric pipes. One fluid flows within the smaller pipe and the other in the annulus. For such an exchanger (outer diameter of the inside pipe is 2 cm; inner diameter of the outside pipe is 4 cm), water flows in the annular space at an average velocity of 0.2 m/s. The water, which cools an organic flowing in the central pipe, has a temperature change from 16 to 28 . In this case calculate the heat transfer coefficient for the water assuming that the exchanger is heavily insulated and that the wall temperature on the inside of the annulus (outside of central pipe) is 30 . And heat transfer rate=?, heat transfer flux=?

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter7: Forced Convection Inside Tubes And Ducts

Section: Chapter Questions

Problem 7.14P

See similar textbooks

Similar questions

The hot akapkan, which enters the inner pipe of a double-pipe exchanger at a speed of 5200 kg/h at 120 °C, is desired to be cooled to 22 "C. In order to cool the hot fluid, the hot fluid is fed tap water at 15 °Dec with a speed of 10780 kg/h between the inner and tooth pipes in the opposite direction. Calculate the length of the double-pipe heat exchanger to be used as a heat exchanger in these conditions.(L?) data: D0=13.8cm Di=12cm K pipe=12w/m.k hi=22w/m^2 k. ho=36w/m^2k CP,hot=2.2 kj/kg.k , CP ,water =1.3 KJ/Kg.k
Water flows through two adiabatic turbines and a heat exchanger as shown in the picture. Hot air is used to provide additional energy to the water between the two turbines. The first turbine has a power output of 8,000 kW. Determine the power output of the second turbine in kW and the process efficiency of each turbine. Determine the state of steam in turbine 1, Formulate the 1st Law for turbine 1, and solve for the flow rate of steam. Formulate the 1st Law for the heat exchanger, and solve for the temperature at exit
Seawater is to be pumped into a large tank at a rate of 165 kg/min. The tank is opwn to atmostsphere and the water enters the tank from a 80 m height. The overall efficiency of the motor pump unit is 75 percent and the motor consumes electricity at a rate of 3.2 KW. If the irreversible headloss in the piping is 7 m, the velocity of the water (in m/s) at the tank inlet is include your freebody diagram A.5.05 B.8.7 C.6.21 D.7.12
In a countercurrent double-pipe heat exchanger, the hot oil entering the inner tube at 420 K with a flow rate of 60 g/s is required to be cooled to 320 K. In the space between the outer tube and the inner tube of the heat exchanger, cooling water flows at the same linear speed as the oil. Cooling water enters the heat exchanger at 290 K. The inner tube inner diameter of the heat exchanger is 25 mm and the outer tube inner diameter is 40 mm. Calculate the length of the heat exchanger. The oil side heat transfer coefficient is 1.6 kW/m2 K, and the water side heat transfer coefficient is 3.6 kW/m2 K. The densities of oil and water can be taken as 0.8 and 1.0 g/cm3, respectively, and the specific heats of oil and water can be taken as 2.0 and 4.2 kJ/kg K, respectively. Wall effects can be neglected. Flow cross-sectional area = (PI)*D2 /4 F2
Water is flowing through a large circular conduit with inside radius R and a velocity profile given by the equation: v(fps) = 8 [1- (r/R)2]. Determine the mass flow rate through the pipe and the average water velocity in the 2.0 ft pipe. ) 7650 lbs and 40 ft/s ) 7057 lbs and 36 ft/s ) 6580 lbs and 39 ft/s ) 7345 lbs and 34 ft/s
In climates with low night-time temperatures, an energy-efficient way of cooling a house is to install a fan in the ceiling that draws air from the interior of the house and discharges it to a ventilated attic space. Consider a house whose interior air volume is 720 m3 If air in the house is to be exchanged once every 20 minutes, determine (a) the required flow rate of the fan and (b) the average discharge speed of air if the fan diameter is 0.5 m..
Water stream (density 997 kg/m3) is fed to the shell side of a shell and tube heat exchanger in a mass flow rate of 561.9 t/h. The inner diameterof the shell is 45 cm, it contains 70 tubes of diameter 25/30 mm.Give the linear velocity at the shell side in m/s.
Hot fluid enters at a flow rate of 3 kg/sec with an inlet temperature of 150 C while cold fluid enters 5 kg/sec and with an inlet temperature of 60 C. Determine the maximum heat transfer that can happen during the heat exchange process? Take specific heat value of the fluid as 2000 J/(kgC)
Water at 90C is being pumped from a large storage tank at 1 atm abs at a rate of 0.189 m3/min by a pump. The motor that drives the pump supplies energy to the pump at a rate of 2 hp. The water pumped through a heat exchanger, where it gives up 700 kW of heat and is then delivered to a large open storage tank at an elevation of 20 m above the first tank. What is the final temperature of the water to the second tank? Neglect kinetic energy.
Water is stored in a large, well-insulated storage tank at 21.0°C open to atmosphere. It is pumped at a rate of 40 m3/h to another tank 25 m above, which is also open to atmosphere. The motor driving the pump supplies energy at the rate of 9.5 kW. The water passes through a heat exchanger where 255 kW of heat is added to the water. The total friction loss (ΣF) in the system is 90.25 J/kg. Determine the final temperature of the water at the second tank.
Liquid benzene at 38 C with a vapor pressure of 26.4 kN/m2 and a density of 860 kg/m3 isto be pumped at a rate of 0.0025 m3/s from a storage tank to a discharge location 3 m abovethe liquid level in the tank. The pump with a mechanical efficiency of 60 percent is 1 mabove the liquid level. The storage tank is at atmospheric pressure. The pressure at the endof the discharge line is 445 kPa absolute. The inside diameter of the pipe used to transfer thebenzene is 0.0409 m. The frictional pressure drops in the suction line and the discharge linehas been evaluated as 3.45 and 37.9 kN/m2, respectively. Determine the head developed bythe pump and the total power requirement. If the pump manufacturer specifies a required netpositive head of 3.0 m, will such a pump be applicable for this service?
A water tank is attached to a piping system with a sharp edge inlet (KL=0.5). Determine the velocity of the outlet water if the system has two elbow pipes (KL=1.5), the length of the entire system is 10m, the diameter is 1.5cm, the friction factor is 0.002 and the height between the water and the outlet are 5m.