The drawing shows a uniform horizontal beam attached to a vertical wall by a frictionless hinge and supported from below at an angle 0= 40° by a brace that is attached to a pin. The beam has a weight of 340 N. Three additional forces keep the beam in equilibrium. The brace applies a force P, and the hinge applies a force with a horizontal component Hand a vertical component V. (a) Draw the free- body diagram showing the forces that act on the beam. Find the magnitudes of the forces (b) P. (c) H, and (d) V. Hinge Pin Beam 0 Brace

The drawing shows a uniform horizontal beam attached to a vertical wall by a frictionless hinge and supported from below at an angle 0= 40° by a brace that is attached to a pin. The beam has a weight of 340 N. Three additional forces keep the beam in equilibrium. The brace applies a force P, and the hinge applies a force with a horizontal component Hand a vertical component V. (a) Draw the free- body diagram showing the forces that act on the beam. Find the magnitudes of the forces (b) P. (c) H, and (d) V. Hinge Pin Beam 0 Brace

Principles of Physics: A Calculus-Based Text

5th Edition

ISBN:9781133104261

Author:Raymond A. Serway, John W. Jewett

Publisher:Raymond A. Serway, John W. Jewett

Chapter10: Rotational Motion

Section: Chapter Questions

Problem 32P

See similar textbooks

Similar questions

A One end of a metal rod of weight Fg and length L presses against a corner between a wall and the floor (Fig. P14.64). A rope is attached to the other end of the rod. Find the magnitude of the tension in the rope if the angle between the rod and the rope is 90.
A wooden door 2.1 m high and 0.90 m wide is hung by two hinges 1.8 m apart. The lower hinge is 15 cm above the bottom of the door. The center of mass of the door is at its geometric center, and the weight of the door is 260 N, which is supported equally by both hinges. Find the horizontal force exerted by each hinge on the door.
a uniform beam with a weight of 60 N and a length of 3.2 m is hinged at its lower end, and a horizontal force of magnitude 50 N acts at its upper end.The beam is held vertical by a cable that makes angle u = 25° with the ground and is attached to the beam at height h = 2.0 m. What are (a) the tension in the cable and (b) the force on the beam from the hinge in unit-vector notation?
A person is standing on a section of uniform scaffolding as shown in the figure. The section of scaffolding is L = 1.50 m in length, has a ms = 24.5 kg mass and is supported by three ropes as shown. Determine the magnitude of the tension in each rope when a person with a weight of Wp = 640 N is a distance d = 0.700 m from the left end. magnitude of T1      N magnitude of T2 N magnitude of T3 N
A uniform horizontal beam 5.00 m long and weighting 3.03  102 N is attached to a wall by a pin connection that allows the beam to rotate. Its far end is supported by a cable that makes an angle of 53.0° with the horizontal (Figure (a)). If a person weighing 6.05  102 N stands 1.60 m from the wall, find the magnitude of the tension  in the cable and the force  exerted by the wall on the beam. T =  N Rx =  N Ry =  N Even if we selected some other axis for the torque equation, the solution would be the same. For example, if the axis were to pass through the center of gravity of the beam, the torque equation would involve both T and Ry. Together with Equations (1) and (2), however, the unknowns could still be found—a good exercise. In this example, notice the steps of the Problem-Solving Strategy could be carried out in the explicit recommended order.QUESTION What happens to the tension in the cable if the man in Figure (a) moves farther away from the wall? The tension would…
A uniform horizontal beam 5.00 m long and weighting 3.03  102 N is attached to a wall by a pin connection that allows the beam to rotate. Its far end is supported by a cable that makes an angle of 53.0° with the horizontal (Figure (a)). If a person weighing 6.05  102 N stands 1.60 m from the wall, find the magnitude of the tension  in the cable and the force  exerted by the wall on the beam. T =  N Rx =  N Ry =  N
In the figure, horizontal scaffold 2, with uniform mass m2 = 29 kg and length L2 = 2.3 m, hangs from horizontal scaffold 1, with uniform mass m1 = 54 kg. A 17 kg box of nails lies on scaffold 2, centered at distance d = 0.80 m from the left end. What is the tension T in the cable indicated?
A uniform plank of length 2.00 m and mass 30.0 kg is supported by three ropes, as indicated by the blue vectors. Find the tension in each rope when a 700 N person is d = 0.500 m from the left end
A uniform horizontal beam 10.0 m long and a mass of 82 kg is attached to support cables on either end. The cable on the left end makes an angle of 120 with x-axis and the cable on the right end makes an angle of 30̊ with the x-axis. If a person of mass 82 kg stands 7 m from the right end, find (a) the magnitude of the tensions TL and TR in the cables.
A 10 m ladder with a mass of 15 kg leans against the wall. If the ladder is in static equilibrium, what must be the normal force from the ground, assuming the wall is frictionless? 30 N 73.5 N 147 N 15 N
Two painters are carrying a uniform horizontal ladder that is 12 feet long and weighs 200 N. If one person applies an upward force equal to 85 N at one end, at what point does the other person lift?
A door has a height of 2.1 m along a y axis that extends vertically upward and a width of 0.91 m along an x axis that extends outward from the hinged edge of the door.A hinge 0.30 m from the top and a hinge 0.30 m from the bottom each support half the door’s mass, which is 27 kg. In unit-vector notation, what are the forces on the door at (a) the top hinge and (b) the bottom hinge?