1. Water is being pumped from the lower reservoir to the upper reservoir. Find the pump horsepower required, assuming 75% pump efficiency. Neglect minor losses. Elev. 132.0 ft hi ft H, ft Water P hp Elev. 97.5 ft Pump Water Q = 23.0 ft'/s D = 24 in Pipe 3 L = 3600 ft C = 120

1. Water is being pumped from the lower reservoir to the upper reservoir. Find the pump horsepower required, assuming 75% pump efficiency. Neglect minor losses. Elev. 132.0 ft hi ft H, ft Water P hp Elev. 97.5 ft Pump Water Q = 23.0 ft'/s D = 24 in Pipe 3 L = 3600 ft C = 120

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Q1: Consider the gravimetric concrete dam shown in Fig. 1. (a) Draw the flow net for the case shown…

A: Gravimetric concrete dam A gravity dam is a structure composed of concrete or stone masonry that is…

Q: A large tank open to the atmosphere is filled with water to a height of 9.3 m from the outlet tap. A…

A: Discharge through the mouth piece= Q=Cd a2gH Velocity = Q/a= Cd2gH= 0.7072*9.81*9.3= 9.55 m/s So the…

Q: I A pump impeller is 37.5 cm in diama and discharges water with velocity components of 2 m/s and 12…

Q: 1. Water at 41 "C flows through an inclined plane. Determine the velocity and direction of the flow…

Q: 3. A pump draws water from a 20 cm diam suction pipe and discharges through a 15 cm diam pipe in…

Q: Water flows in a trapezoidal canal (lower base=2m; height=.75m;water surface=3.5m), the velocity is…

Q: A conical tank is full of water. It has a diameter of 10 cm. Find the work done in N.m in pumping…

A: Diameter of conical tank=10 cm Depth=20 cm Work done =?

Q: 33 Elev A Water Elev C Turbine Elev B Water flows from Reservoir A (Elev 128 ft.) to a turbine (Elev…

A: Given Discharge, Q = 35 ft3/s Elevation of reservoir A = 128 ft Elevation of Turbine = 73 ft…

Q: A pump draws water from a 20 cm diam suction pipe and discharges through a 15 cm diam pipe in which…

A: Pump efficiency is generally the ratio of water power output from the pump to the shaft power input…

Q: An open circular cylinder with 2m of water is acted upon by an unbalanced upward force of 20 kN. The…

A: aWe knowF=maF=ρwVa20×1000N=1000kgm36.28m3aa=3.18ms2

Q: The rectangular bin with an inclined gate AB is filled with water to the depth shown. Determine the…

Q: An open tank contains 5 m deep of liquid having a unit weight of 7 kN/m. Water is poured over the…

Q: A closed cylindrical tank 1.89m high and 0.99m in diameter contains water of height 1.35m. When the…

A: We know that y=ω2r22gy=2020.992229.81y=4.9954my'=4.9954m-1.35m=3.6454m

Q: T530 m-150 me. C » 130 C ;=120 I830 m-300 mm, C, » 130 250 mm__ El. 0.0 1220 m-250 mm C C; = 120

A: The given information is The pressure head at A is 3.05 m The pressure head at B is 89.9m The…

Q: The pump is used to deliver the water from the pond at A to the channel at B with a flow of 0.03…

A: Q=0.06m3s=vAv=0.03m3sπ4(0.15)2=1.6976ms

Q: Water flows from Reservoir A (Elev 125 m.) to a turbine (Elev 67 m.) then discharges into tailtrace…

Q: Underground water is pumped to a sufficient height through 10 cm diameter pipe that consists of a 3…

Q: A pump draws water from a 20 cm diam suction pipe and discharges through a 15 cm diam pipe in which…

A: Given,

Q: QI: Determine: 1- The diameter of pipe for transmitting maximum power. 2- The velocity, and 3- Power…

Q: A 2-m-diameter cylinder is placed in a uniform water flow of 4 m/s. Find p(0) on the front half of…

A: Since we only answer up to first part, we’ll answer the first one. Please resubmit the question and…

Q: Problem 6. The 1.2 m - diameter log with specific gravity of 0.8 is 3.0 m long into the paper. The…

Q: Water flows through a pipe AB 1.2 m diameter at 3 m/s and then passes through a pipe BC 1.5 m…

A: Given: The diameter of the pipe AB is 1.2 m. The velocity of flow in pipe AB is 3 m/s. The diameter…

Q: Problem 6. The 1.2 m - diameter log with specific gravity of 0.8 is 3.0 m long into the paper. The…

Q: 2. Water is pumped from reservoir A at elev. 15 m by a 150mm diameter pipe 200m long with a friction…

Q: he power input of the pump is 10 kW and the friction head loss between A and B is 1.25 n. If the…

A: DA=0.5m DB=0.25m ZA=0m ZB=2m

Q: 0.7 m E Water xy-Ay B A=0.4 m B 0.9 m2 H = 2.5m 3.0 m 0.5 m -2.2 m- he curtain of a dam shown in the…

A: To find total force

Q: Water at 10⁰C flows at the rate of 900 L/min from the reservoir and through the pipe shown in the…

Q: 7. For the Pitot Tube below, determine the height that the fluid rises, L, in the column if water is…

A: Velocity of flow through pitot tube is given and it has been asked to determine height of fluid…

Q: A centrifugal pump which runs at 104.3 rad ·s−1 (16.6 rev/s) is mounted so that its centre is 2.4 m…

Q: For the sluice gate below, water is flowing under the gate in a rectangular channel (5 ft bottom…

Q: 90.Water is pumped from the reservoir with a surface elevation of 200 m across the valley to another…

A: Given data Length of pipe Diameter of pipe Pressure at halfway Elevations

Q: Water enters the pump of a steam power plant at 20 kPa and 50 °C (p = 988 kg/m', & Pr = 12.352 kPa)…

Q: Two identical pumps connected in series using a pipe 3.5 cm diameter with water flowing at velocity…

A: Given data: G1=0.1 bar=0.1×105 N/m2G2=0.6 bar=0.6×105 N/m2V (velocity of flow) = 2.5 m/sD = 3.5 cm

Q: Water from a reservoir is pumped over a hill through a pipe 90 cm in diameter, and a pressure of 200…

A: Given: The diameter of the pipe is 90 cm. The pressure is 200 KPa. The height of the summit is 90 m.…

Q: Q: In a rough pipe of diameter 500mm and length 3500m, water is flowing at the rate of 0.5 m/s. If…

Q: Consider the figure below. The pump supplies water from reservoir A to reservoir B through the 500mm…

A: The answers given for subpart (a) and (b) are not correct.

Q: .) For the tank shown below (width = 1.25 m), determine (6.a) the maximum horizontal acceleration…

Q: A circular orifice 1inches in diameter in the vertical side of a vessel, discharges water under a…

A: Given: Diameter of orifice Horizontal ordinate Vertical ordinate Head Weight of water Time To…

Q: The rectangular bin with an inclined gate AB is filled with water to the depth shown. Determine the…

A: Draw the pressure diagram. Then using the properties of pressure diagram the depth of center of…

Q: H.W.2: Calculate the maximum difference of head in the structure, where the soil is coarse sand then…

A: Given, H=68-60=8 m C= 6 Safe creep length =L=CH L=2d1+d2+d3+13x+6+6+3+6=34+13x+21

Q: Water at 15°C is drained from a large reservoir using two horizontal plastic pipes connected in…

A: Solution Given Data T=150C First Pipe= 13 m Long and 15 cm Dia Second Pipe= 35 m Long and 5 cm Dia…

Q: SITUATION 4: Water is drained from a large reservoir using two horizontal pipes connected in series.…

Q: A pump draws water from a 20 cm diam suction pipe and discharges through a 15 cm diam pipe in which…

A: The head, pressure, or power (are the same) is lost through running water in a pipe or station. Due…

Q: Q: In a rough pipe of diameter 500mm and length 3500m, water is flowing at the rate of 0.5 m'/s. If…

Q: ne dam and the sa ng vertical sheet pil he flow net by using te the flow rate q um te the water…

A: SOLUTION OF ABOVE QUESTION IS BELOW:

Q: Water is pumped from the reservoir with a surface elevation of 200 m across the valley to another…

A: Given that: Surface elevation of reservoir = 200mSurface elevation of other…

Q: 4. Three cylinders are piled in a rectangular ditch as shown. Neglecting friction, determine the…

A: Determine the reaction at cylinder A and the vertical wall.

Q: 3. A pump draws water from a 20 cm diam suction pipe and discharges through a 15 cm diam pipe in…

Q: Q4: Determine the maximum height increase provided by a 7.46 KW pump with a 6-cm-diameter inlet and…

A: Step 1

Q: Pb # 4: A Reg.No-m length of smooth horizontal pipe is attached to a large reservoir as shown in…

Concept explainers

Pressurized pipe flow

A 15-kilometer-long pipe with a pipe diameter of one meter transports water at a speed of one meter per second. The pipe has a friction coefficient of 0.005. Calculate the frictional head loss?

Question

100%

Answer in this format.
Sketch:
Given:
Required:
Solution: (Please answer in detailed (step by step). Indicate labels on what you are doing/performing, for example what formula is used)
1.
Water is being pumped from the lower reservoir to the upper reservoir. Find the pump horsepower
required, assuming 75% pump efficiency. Neglect minor losses.
Elev. 132.0 ft
hi
ft
H,
ft
Water
P
hp
Elev. 97.5 ft
Pump
Water
Q = 23.0 ft'/s
D = 24 in
L = 3600 ft
C = 120
Pipe

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Topic: Flow in closed conduits For the pipe network shown, the flow of water from A to the first junction is 2 cubic feet per second. Assuming all pipes have a friction factor of 0.020 Which of the following statements is FALSE? *The inflow in pipe 1 is equal to the ouflow in pipe 5. *The sum of the discharge of pipes 2 and 4 is equal to the ouflow in pipe 5. *The sum of the discharge of pipes 2 and 3 is equal to the inflow as well as the outflow. *The inflow in pipe 1 is equal to the outflow in pipe 5 Please answer with complete and detailed solution. ASAP. Thank you
Completely solve. Write legibly. Box the final answer. Water is flowing through a pipe 1/3 ft. inside diameter into a pipe 1'' in diameter at a rate of 12.62 lps. If the pressure in the 4'' pipe is 275.8 kPa, what is the pressure in the small pipe assuming no energy loss and friction head loss?
Water is drained from a vertical cylindrical tank by opening a valve at the base with the velocity at which the water level drops is: a) Employ any suitable numerical methods to estimate the water level from t = 0 to t = 10 min to the most accurate value. Answer (in 2 decimal places) : m Answer (in 2 decimal places) : min Please provide full solution
For the pipe system shown in figure 2, find the flow rate in all pipes neglecting all minor losses. Consider that the pump shown develops 9m of head when velocity in pipe C is 3.6 m/sec. Consider the flowing given data: Water surface in the reservoir is 94m, length of pipe A, B and C are all 840m long each and all have the same diameter of 0.7m with f=0.022 Subject Name is Advance Fluid Mechanics
A 12-inch by 6-inch Venturi meter is installed in a vertical pipeline carrying water as shown inthe Figure C. The flow is upward through the meter. A differential manometer containing fluid,with sp.gr 1.67, is attached to inlet and throat, the difference z in gage levels being 5.76 ft.Neglecting loss of head, write energy equation from inlet to throat of meter. Also write stepby step equation of the differential gage between inlet and throat and combine the twoequations to compute the discharge
A pump draws 52 lit/sec of water from reservoir A to reservoir B as shown. Assuming f = 0.041 for all pipes, compute the horsepower delivered by the pump Elevation of reservoir A = 13 m Elevation of reservoir B = 89 m Pipeline 1 : 236 mm, 712 m (diameter, length) Pipeline 2 : 156 mm, 1595 m (diameter, length) Round your answer to 3 decimal places.
The velocities recorded by current meter in a stream are given below. Find the discharge per unit width of stream near the point of measurement. Take the depth of flow at the point as 5m. Note : For Detail See Figure Attached . Please Provide Solution In Detail ASAP.
kindly help me with this problems INSTRUCTIONS: Solve the problems neatly and systematically. Use free-floating decimals in all your calculations and in expressing your answers. Box your final answers. 4. Calculate for the maximum height of the water stream that could rise from a nozzle pointed straight up. The nozzle is connected at the bottom of the tank having a water level of 15 m and the pressure above it is at 3atm gauge.
Figure shows that the pipe flow of 50 m^3/hr, is driven by pressurized air in the tank Determine the head loss in the "smooth" pipe in meters if its friction factor is 0.014. *12.9517*99.9358*30.4889*39.5136 What gage pressure p1 in kPa, is needed to provide the given flow rate? *1121 kPa*1692 kPa*1328 kPa*1725 kPa Please answer with complete and detailed solutions. thank you. ASAP
Given a portion of a water supply pipe network system below. Determine the actual flow in each pipe and the respective head losses. Assume flow in pipes AB and DE in loop I and II respectively equal to 0.10 m3/s clockwise for the first trial. Use Darcy-Weisbach Formula with f = 0.02. Pipes Length (m) Diameter (cm) AB 500 20 BC 600 15 CD 500 20 DE 400 20 EA 700 25 AC 1000 15
Consider the uniform flow of water in a wide channel with a velocity of 8 m/s and flow depth of 0.8m. Water flows over a 30-cm-high bump. Determine the change in the water surface level over thebump and flow over the bump is subcritical or supercritical.Your answer should include the following: B 2.1 Assumptions to be made to determine changes in the water surface levelover the bumpB 2.2 Determine flow over the bumpB 2.3 Observations and comments
Solve in 5 min