Answered: If the hoop stress on a cylindrical…

If the hoop stress on a cylindrical pressure vessel with diameter d, thickness t and gauge pressure p is 58.54 MPa, then the longitudinal stress must be equal to (in MPa)..

Principles of Foundation Engineering (MindTap Course List)

9th Edition

ISBN:9781337705028

Author:Braja M. Das, Nagaratnam Sivakugan

Publisher:Braja M. Das, Nagaratnam Sivakugan

Chapter8: Vertical Stress Increase In Soil

Section: Chapter Questions

Problem 8.13P

See similar textbooks

Related questions

Q: The hoop stress at a point on the surface of a thin cylindrical pressure vessel is computed to be…

A: To find out the maximum shear stress at this point.

Q: A closed cylindrical tank 900 mm in diameter has a wall thickness of 0.8 mm. The allowable…

Q: For the given plane stress state '=120 MPa, ' c= 100 MPa and °c=150 MРа, σύ. . Calculate the…

A: Given: σb=120 MPaτc=100 MPaσa=150 MPa

Q: For a cylindrical pressure vessel, the normal stress component on a transverse section is known as…

A: Lets depict various stress images.

Q: For earth pressure at rest, there will be no a) vertical stress b) shear stress c) horizontal stress…

A: For earth pressure at rest there will be both : Horizontal stress Vertical stress There is no…

Q: A) Show the following on Mohr's stress circle: 1-The value of direct stress in the plane of the…

A: Plotted values and labelled value that is asked in question A is shown in next step Further plane…

Q: he free surface of a stressed body, a normal stress magnitude of Sy - 69 MPa (C) a zontal plane. One…

Q: The principal stress for machine component boiler are o, 0.50 and 0. If yield stress is found 240…

Q: Determine the normal stress in a ball, which has an outside diameter of 195 mm and a wall thickness…

A: step 1-

Q: 4. A beam of rectangular cross section 40 mm by 100 mm is carrying a bending moment of M = 21 kN.m…

A: The given data is: b=40 mm d=100 mm M=21 KN-m σy=240 MPa E=200 GPa

Q: a cylindrical steel pressure vessel 400 mm in diameter with a wall thickness of 20 mm, can only be…

A: It is required to determine the radius of spherical vessel. V=43πr30.075 m3=43πr3r3=0.018 m3r=0.26 m…

Q: The built-up shaft consists of a pipe AB and solid rod BC. The pipe has an inner diameter of 20 mm…

Q: Determine the maximum stress in the member CD if you know that the distributed load W = 40 kN/m, the…

Q: When filled to capacity, the unpressurized storage tank shown contains water to a height of h 10 ft.…

A: We need to find hoop stress.

Q: A cylindrical shell made of mild steel plate of 100 cm diameter is to be subjected to an internal…

A: Given data- A cylindrical shell-Diameter of steel plate (D) = 100 cmInternal pressure (P) = 10…

Q: If w=15 kN/m, determine the following: a. Maximum tensile stress in the beam b. Maximum compressive…

A: Given UVL intensity = 15 KN/m First we have to calculate maximum bending moment from given beam.…

Q: A closed cylindrical tank containing a pressurized fluid has an inside diameter of 510 mm and a wall…

A: Given data, Internal fluid pressure P = 2.40 MPa Internal diameter D = 510 mm Wall thickness t = 10…

Q: A thin walled cylindrical pressure vessel having mean radius 100 mm and wall thickness 5 mm, is…

Q: Which of the following is NOT TRUE for a state of stress at point for a thin spherical pressure…

Q: A cylindrical tank has an internal pressure of 1.5Mpa. - Determine the diameter of the cylindrical…

A: Given: The internal pressure is 1.5 MPa.

Q: At a point in a stressed material, the major principal stress is 7.2 ksi compression and the minor…

A: It is required to determine the maximum shear stress. We know that, the maximum shear stress acts at…

Q: Problems for Practice Situation 4 A point load P-5 kN at the origin (0, 0, 0) of a ground surface…

Q: gas under pressure of 2.2 MPa. a. b. Determine the value of the tangential stress in the tank wall…

Q: A thin-walled long cylindrical tank of inside radius r is subjected simultaneously to internal gas…

Q: a)Calculate the stress components acting on the inclined plane AB. b)Calculate prime stresses…

A: Given data: σx = -25 MPa (Compressive) σy = 50 MPa (Tensile) shear stress = -60 MPa (Causing…

Q: Problem 5 An 8mm thick steel tank has an outside diameter of 608 mm and a length of 3m. it is…

A: Internal pressure (P) =2MPa Diameter (d) =608mm Thickness(t) =8mm

Q: At a point in a stressed material, the major principal stress is 180 kPa compression and the minor…

A: Given :σx = -180 Kpa σy =…

Q: 1. At the proportional limit, a certain material has a stress of 78 MPa as the strain is 0.0004.…

A: Given data , Material stress=78MPa Strain = .0004 Calculate modulus of elasticity of…

Q: Two solid cylindrical rods (1) and (2) are joined together at flange B and loaded as shown. The…

Q: Determine the effective stress at point B (in kN/m2). b. Determine the effective stress at point C…

Q: Cross section below is under a Moment as shown in the a. Normal stress at B b. Normal stress at D B…

Q: If w=15 kN/m, determine the following: a. Maximum tensile stress in the beam b. Maximum compressive…

A: The given figure is shown below:

Q: a. Determine the horizontal shearing stress at 20 mm above the Neutral Axis o. Determine the…

Q: The vertical surface stress is 100 kPa. The stress increase (kPa) at A is 100 kPa 2m 2m 2m 4.4 O 20…

Q: Vertical stress due to a line load Homework: An inclined line load of magnitude 10 kN/m. Determine…

A: Resolving the load into horizontal and vertical components: For the vertical line load: x/z=5/4=1.25…

Q: Jor 6 m 5 kN/m -250 mm 20 mm-

A: Determine the maximum tensile stress in the following beam:

Q: A thin walled cylindrical pressure vessel having a radius of 0.5 m and wall thickness of 25 mm is…

A: Thin cylinder: Thin cylinders are used for pressure tanks, pipes, boiler shells, and other…

Q: determine the diameter of the rod C if the allowable stress 86.60 MPa. Neglect the…

A: Free body diagram of Bar AB

Q: A pressure-vessel head is fabricated by gluing the circular plate to the end of the vessel as shown…

Q: concendrated load of 2000 kN is applied at the ground surface. Determine the vertical stress at a…

A: Solution: Given Data: Concentrated load=2000 kN

Q: A cylindrical steel pressure vessel with a diameter of 1200 mm and a wall thickness of 20 mm is…

A: In thin cylinders the circumferential stress is twice than that longitudinal stress.

Q: A spherical pressure vessel has an inner radius of 1.5 m and a wall thickness of 12 mm. Draw Mohr’s…

A: Given data: Inner radius of spherical vessel = r = 1.5 m= 1500 mm Wall thickness of spherical vessel…

Q: Example/ A cylindrical steel pressure vessel 400 mm in diameter with a wall thickness of 20 mm, is…

A: Given data: Diameter of the vessel (D) = 400mm the thickness of the wall (t) = 20mm the internal…

Q: The normal stress (kPa) on a plane inclined at 30 degrees from the horizontal is most nearly (anti-…

A: given stress on vertical and horizontal plane and shear stress also

Q: Which of the following is NOT TRUE for a state of stress at point for a th spherical pressure…

A: From the given question it is required to find what is not true regarding a state of stress at a…

Q: ressure has an outside diameter of mm and a wall thickness of 11 mm. oute the longitudinal stress…

A: Given data- Pressure (P) = 1523 kpa Outside diameter (D) = 432 mm Internal diameter (d) = 432…

Q: A cylindrical tank with an inner diameter of 2.5 m and a wall thickness of 32 mm is made of a steel…

A: The pressure vessels are classified into two types namely based on the ratio of internal diameter to…

Q: a.)For the given figure, determine the normal stress in MPa at segment AB, Cross-section of AB is…

Concept explainers

Methods to Determine Vertical Stress

The load applied to the soil is transferred to the underground. The presence of water at soil pores and solid grains above the soil are the primary components that are responsible for the effective load transfer. Due to the load acting, the internal component of the soil or the underground formations undergoes deformations or a tectonic shift. The amount of deformation depends upon the amount of load acting on the soil surface, which indeed, depends on the weight of everything present above the soil. Due to this, the underground soil element develops internal stresses which try to resist the tectonic changes.

Question

If the hoop stress on a cylindrical pressure vessel with diameter d, thickness t and gauge pressure p is 58.54 MPa, then the longitudinal stress must be equal to (in MPa)...

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1 Longitudinal stress

VIEW

Step 2 Longitudinal stress

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Determine the normal stress in a ball, which has an outside diameter of 165 mm and a wall thickness of 3.4 mm, when the ball is inflated to a gauge pressure of 81 kPa.
A closed cylindrical tank, placed horizontally, 400 mm in internal diameter and 2.2 mm thick is subjected to an axial compressive force (along its longitudinal axis) and uniform internal pressure. The stresses acting on an element of side is shown in the figure. a. What is the magnitude of the internal pressure in MPa?b. What is the applied axial force in kN?c. What is the maximum shear stress in MPa?
A hollow metal tube with an inside diameter of 265 centimeters must carry a tensile load of 910kN. Determine the outside diameter of the tube, in meters, if the stress is limited to 171 MPa.
A closed cylindrical tank containing a pressurized fluid has an inside diameter of 510 mm and a wall thickness of 10 mm. The tank is pressurized to 2.40 MPa. Determine the longitudinal stress in the wall of the tank.
Two solid cylindrical rods support a load of P = 25 kN as shown. Rod (1) has a diameter of 13 mm, and the diameter of rod (2) is 12 mm. Determine the axial stress in rod (1).
refer to the figure due to application of line load q1 and q2 . the vertical stress increase at point a is 42 kn/m2 determine the magnitude of q
A square hollow bar having an outside dimension of 250 mm by 250 mm with 6 mm thick is to be replaced by a solid circular bar. a) Determine the required diameter of bar so that the maximum shear stress in the bar will not exceed the maximum shear stress in the tube. b) If the computed value of diameter in the previous question increase by 15%, what is the new shear stress of the circular bar? c) Determine the angle of twist in degrees of the tube if the length of the tube is 1m and the shear modulus is 80 GPa. Use T=14 kN-m.
a)Calculate the stress components acting on the inclined plane AB. b)Calculate prime stresses c)Calculate the maximum shear stress Shear stress = 60 Mpa
QUESTION 5 The solid shaft as shown in Figure 5 is made of material that has an allowable stress of 275 MPa. Determine the required diameter of the shaft to the nearest mm.
A hollow metal tube with an inside diameter of 55 centimeters must carry a tensile load of 490 kN. Determine the outside diameter of the tube, in meters, if the stress is limited to 129 MPa.
a cylindrical steel pressure vessel 400 mm in diameter with a wall thickness of 20 mm, can only be subjected to a maximum stress value of 120MN/m^2. if the same amount of pressure is applied/ contained in a spherical vessel whose internal volume is 0.075m^3, what must be the sphere's material thickness if it is experiencing a stress value of 127.484 MN/m^2. the radial stress for spherical vessel is theta sub s equals pD/4t
A strip loading of infinite length is shown in figure below compute the vertical stress increase at a point A.B.C.D.