The fatigue data for a ductile cast iron is given in the table below.Stress Amplitude[MPa]248236224213201193193193Cycles to Failure1 × 10³3 x 1051 x 1063 x 10°1 x 107a) Create a S-N curve from the data.b) What is the fatigue limit for this alloy?c) Determine the fatigue life at 230 Mpa and 175Mpad) Determine the fatigue strength at 2x105 and 6x106 cycles3 x 1071 × 1083 x 108

Since we only answer upto 3 subparts, we will answer the first 3. Please resubmit the question and…

The fatigue data for a ductile cast iron is given in the table below. Stress Amplitude [MPa] 248 236 224 213 201 193 193 193 Cycles to Failure 1 × 10³ 3 x 10³ 1 x 10° 3 x 106 1 x 107 3 x 107 1 x 108 3 x 108 a) Create a S-N curve from the data. b) What is the fatigue limit for this alloy? c) Determine the fatigue life at 230 Mpa and 175Mpa d) Determine the fatigue strength at 2x105 and 6x106 cycles

The fatigue data for a ductile cast iron is given in the table below. Stress Amplitude [MPa] 248 236 224 213 201 193 193 193 Cycles to Failure 1 × 10³ 3 x 10³ 1 x 10° 3 x 106 1 x 107 3 x 107 1 x 108 3 x 108 a) Create a S-N curve from the data. b) What is the fatigue limit for this alloy? c) Determine the fatigue life at 230 Mpa and 175Mpa d) Determine the fatigue strength at 2x105 and 6x106 cycles

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Select All the correct statements from below. a. If the averaged distance between partial dislocations for material A observed under TEM is smaller than material B, the estimated stacking fault energy of material A is lower than material B. b. K_IC is a material property that doesn't change with testing conditions c. The main difference between high cycle fatigue and low cycle fatigue is the difference in the number of cycles to failure d. A negative R value in fatigue test indicate the minimum stress is compressive in nature
Use the fatigue curves below to answer the following questions.: Which curve represents a sample subjected to fatigue at the lowest mean tensile stress? (Select One) Group of answer choices Curve A Curve B Curve C
Note: Kindly give me both right answers. A) Did the ductile materials (annealed and aluminium) react differently to the two different testing methods (hardness test vs. tensile test)? What does this say about the behaviour of ductile materials in compression vs. tension? B) Did the brittle material (quenched) react differently to the two different testing methods (hardness test vs. tensile test)? What does this say about the behaviour of brittle materials in compression vs. tension? （Three to five sentence answers are good）（engineering material)
And **The modulus of elasticity** (MPa) I need a clear step by step answer please :)
HEY MAY YOU PLEASE HELP ME WITH THE FOLLOWING QUESTIONS Which one of the alloys given below will have the highest hardness. Give a brief explanation and illustrate your answer with an applicable calculation. 98% Pb + 2% Mg (RPb = 0.175nm, RMg = 0.160nm) 98% Pb + 2% Sn (RPb = 0.175nm, RSn = 0.151nm)
Mild steel 1 Young;s modulus 1219.5 Yield strain and stress (0.4101,500.08) Failure stress and strain :not able to find because the given data shows the experiment did not reach the failure point. if the material stress and strain does not reach a failure point ,what dose it means , does it means that the material is more stronger?
Based upon the percent elongation of a tensile sample, A ductile engineering materials to find by value equal to or greater than 5% and a brutal materials defined by a value less than 5% true or false?
A cylindrical rod 500 mm long, having a diameter of 12.7 mm, is subjected to a tensile load of 30,000 N. The rod is to experience an elongation not more than 1.3 mm and FOS ≥ 1.5 setting yield strength as a criteria. Additional constraints to be met are max specific stiffness and %EL not more than 0.15. Which of the below listed materials are possible candidates? Justify your choice(s) by making a table of constraints. Materials Modulus of Elasticity, (GPa) Yield Strength, (MPa) Tensile Strength, (MPa) Aluminum alloy 70 300 450 Titanium alloy 107 400 550 Steel alloy 207 500 750
The following data are obtained from a tensile test of a copper specimen. - The load at the yield point is 157 kN. - Length of the specimen is 23 mm. - The yield strength is 89 kN/mm2. - The percentage of elongation is 45 %. Determine the following (i) Diameter of the specimen, ii) Final length of the specimen, iii) Stress under an elastic load of 18 kN, iv) Young's Modulus if the elongation is 1.3 mm at 18 kN and (v) Final diameter if the percentage of reduction in area is 25 %. Solution: Initial Cross-sectional Area (in mm2) The Diameter of the Specimen (in mm) Final Length of the Specimen (in mm) Stress at the elastic load (in N/mm2) Young's Modulus of the Specimen (in N/mm2) Final Area of the Specimen at Fracture (in mm) Final Diameter of the Specimen after Fracture (in mm)
The following data are obtained from a tensile test of a copper specimen. - The load at the yield point is 151 kN. - Length of the specimen is 23 mm. - The yield strength is 79 kN/mm2. - The percentage of elongation is 45 %. Determine the following (i) Diameter of the specimen, ii) Final length of the specimen, iii) Stress under an elastic load of 17 kN, iv) Young's Modulus if the elongation is 2.4 mm at 17 kN and (v) Final diameter if the percentage of reduction in area is 24 %. Find: 1)Stress at the elastic load (in N/mm2) 2)Young's Modulus of the Specimen (in N/mm2) 3)Final Area of the Specimen at Fracture (in mm) 4)Final Diameter of the Specimen after Fracture (in mm)
The following data are obtained from a tensile test of a copper specimen. - The load at the yield point is 151 kN. - Length of the specimen is 23 mm. - The yield strength is 79 kN/mm2. - The percentage of elongation is 45 %. Determine the following (i) Diameter of the specimen, ii) Final length of the specimen, iii) Stress under an elastic load of 17 kN, iv) Young's Modulus if the elongation is 2.4 mm at 17 kN and (v) Final diameter if the percentage of reduction in area is 24 %. THE QUESTION IS : FIND THE Final Diameter of the Specimen after Fracture (in mm)????
The following data are obtained from a tensile test of a copper specimen. - The load at the yield point is 159 kN. - Length of the specimen is 29 mm. - The yield strength is 82 kN/mm2. - The percentage of elongation is 47 %. Determine the following (i) Diameter of the specimen, ii) Final length of the specimen, iii) Stress under an elastic load of 19 kN, iv) Young's Modulus if the elongation is 2.8 mm at 19 kN and (v) Final diameter if the percentage of reduction in area is 21 %. Solution Initial Cross-sectional Area (in mm2) Answer for part 1 The Diameter of the Specimen (in mm) Answer for part 2 Final Length of the Specimen (in mm) Answer for part 3 Stress at the elastic load (in N/mm2) Answer for part 4 Young's Modulus of the Specimen (in N/mm2) Answer for part 5 Final Area of the Specimen at Fracture (in mm) Answer for part 6 Final Diameter of the Specimen after Fracture (in mm)