Answered: The ff are results of a field unit…

The ff are results of a field unit weight determination test Volume hole 0.0016 Mass of moist soil from 3.10kg Water content 12.20% Mas dry 19.50 Determine the relative compaction in %

Fundamentals of Geotechnical Engineering (MindTap Course List)

5th Edition

ISBN:9781305635180

Author:Braja M. Das, Nagaratnam Sivakugan

Publisher:Braja M. Das, Nagaratnam Sivakugan

Chapter5: Soil Compaction

Section: Chapter Questions

Problem 5.5P

See similar textbooks

Related questions

Q: The beam is supported by two rods AB and CD that have cross- sectional areas of 18 mm² and 7.5 mm²,…

A: Take moment about A∑ MA=06d-FCD3=0FCD=2d∑ Fy=0FAB+FCD=6FAB=6-2d

Q: Find the hydraulic radius of rectangular channel having wetted area 16 m2 and wetted perimeter 12 m

Q: 50. What should be the height (m) of a lighthouse, so that it can be visible from a distance of 3…

Q: % moisture is 17.58 kN/m3. Determine the mass of water (kg), per cubic meter, that must be added to…

Q: A cable is loaded as shown in the figure. A 3 m 5 m B 20 kN T 5m с 30 kN 6 m D 10 KN 4 m E 4 m

Q: Problem 02. The fixed supported frame below carried a uniformly distributed load of 30KN/m along…

Q: Find the value of void ratio if porosity of soil is 0.0012

A: Introduction : The given question is related with geotechnical engineering . In this this question…

Q: QUESTION 15 A 20 m normal weight concrete pile is driven into the ground. How long will it take in…

Q: how far will it then move along the other incline? What will be the velocity when it returns to B?…

Q: No. 1. A simple beam AB is loaded by two segments of uniform load and two horizontal forces acting…

A: As only first part A is being asked. The solution is presented in next step

Q: dx If √²-2x - 4 substitutions is used? (a) x = x = √5 sec 0 (c) x = √5 sin 0 is solved by…

Q: A concrete beam of rectangular cross-section of size 120 mm x 200 mm is prestressed by a straight…

A: given- concrete beam rectangular section 120 mm×200 mmefffective force=150 kNeccentricity e=20 mm

Q: What is construction engineering and management about? What are its functions and outputs?

A: Construction Engineering is a professional discipline that deals with the designing, planning,…

Q: An open rectangular tank 1.5mx1mx1.2m high is completely filled with water when at rest. Determine…

Q: A house in State College, PA consists of the following: 12 single pane windows (each 10 ft by 1 ft…

Q: In a triaxial test for a cohesive soil sample, when the principal stresses are 477.79 kPa and 63.47…

Q: Lould be the height (m) o- it can be visible from (b) 0.605 (d) 0.707

A: Horizontal distance D = 3 km Height of light house h = ?

Q: 1. Draw the shear and bending moment Diagram of the following A) 71kN/m A B |—3 m— 8 m B) 48kN/m 9 m…

Q: 2-123. The container of water has a mass of 20 kg. Block B has a density of 7840 kg/m³ and a mass of…

A: Given:- The mass of the container of water = 20 kg The density of the block B = 7840 kg/m3 The mass…

Q: Compute the Block Shear Strength of the Tension member 2″4 O O 2" 2" %8-in. bolts L 4x4x2 A36 O 1½"

Q: The average effective overburden pressure on 10 m thick homogeneous saturated clay layer is 150 kPa.…

Q: The long chord of a simple curve is 143.68m and makes an angle of 69 degrees with the line…

Q: 95 mm. Constant head difference: 54 cm. Volume of water collected in 4.10 min.: 423 cc Void ratio of…

A: We knowq=kiAVoltime=k(ΔhL)(Area)423×10-6m34.1×60sec=k(0.540.18)(π4×0.952)k=80.86×10-8ms

Q: The overall drag coefficient of an aircraft of weight Wand wing area S is given by Co= a +bC₂² where…

Q: tank 2 m in diameter and 5 m high is made from steel having a thickness of 10mm. A) Determine the…

Q: 40KN ↓ A 27 kN/m ↓ ↓ ↓ ↓ ↓ ↓ fim B C tih с + qm 3m 3m 60 KN-m D

Q: following data relate to a pump-out test: Diameter of well = 24 cm; Thickness of confined aquifer =…

Q: Find the hydraulic radius of rectangular channel having wetted area 16 m2 and wetted perimeter 12 m

Q: The initial void ratio of an inorganic clay is found to be 0.65, while the specific gravity of…

Q: wing that is related to transportation engi

A: A working sketch or blueprint is one that is based on explanations. It's finished with a detailed…

Q: 18.4 19.3 Mass of empty can, g Mass of empty can + wet soil 51.6 45.6 sample, g Mass of empty can +…

Q: draw shear and bending moment diagram. Show completed solution 45 KN 45 AN 71kN/m Lisat tist

A: As per guidelines we can solve one question at a time, please upload separately, Thanks Solution to…

Q: . Determine the specific gravity of soil solids based on the data below: Initial volume of soil in…

A: Final mass of 30.10g should be dry mass. Because saturated mass is already mentioned.

Q: Problem B Equipment Estimating Use the following information for a scraper. Actual cost (delivered)…

A: Actual cost of vehicle= $162000 Useful life = 6*1400= 8400 hrs Life of tires = 3500 hrs No of tire…

Q: locate or calculate the centroid of the shaded area in this problem, please show complete solution.

Q: SITUATION. The figure shows a highway bridge truss. S F G H A B C FE FE 市 Given: S=4m H = 5m Due to…

A: (D) 16m is the correct answer. The question is based on the influence line diagrams. Draw the…

Q: Determine the ultimate moment capacity of the beam with given properties below. d' = 80mm d = 420mm…

Q: Math 6 - Composite Figures - Putt Putt Golf Calculate the area and perimeter of each hole in the…

Q: (b) Determine the percentage error introduced by using R., in place of ko for the following values…

Q: 1. A 30-m tape having a standard length of 30.005 m is to be used to lay-out a building that has…

Q: Find the hydraulic radius of rectangular channel having wetted area 16 m2 and wetted perimeter 12 m

A: Introduction : The given question is related with fluid mechanics . In this question we are provided…

Q: The 16-foot solid steel shaft has been twisted 4 times. Determine the diameter d of the shaft if the…

A: ASKED: To determine the diameter of the solid circular shaft. Given, Length of the shaft (L) = 16…

Q: A 15kN/m 3m 1bokw с 3m EI= constant 3m 30kN/m 6m EP

Q: f the shaft?A

A: We knowμ=Lateral strainLongitudinal strainLateral strain=δddLongitudinal strain=δLL

Q: 17. Refer to the soil profile shown. Given H1 = 9.29 m., and H2 = 5.67 m. If the ground water table…

Q: 3. In an artesian aquifer, the drawdown is 7.4m at a radial distance of 11m from a well after two…

A: To find the pumping time required

Q: that is related in structural enginee

A: A structural drawing is a design or set of plans and details that shows how a building or other…

Q: 3. In an artesian aquifer, the drawdown is 7.4m at a radial distance of 11m from a well after two…

Q: soil the following were obtain: Size of particle 0.48 mm percentage finer 60;Size of particle 0.33

A: Given data- Size of particle 0.48 mm percentage finer 60 D60 = 0.48mm Size of particle 0.33 mm…

Q: In a triaxial test for a cohesive soil sample, when the principal stresses are 483.36 kPa and 60.39…

Concept explainers

Soil Compaction Test

Soil compaction is the major area of geotechnical engineering. Soil is composed of multiple pores present on its surface, while the soil is mainly composed of gravel, sand, rocks, etc. The arrangement of these rocks and gravels is such that they build up voids (spaces) between them, which allows spaces for the roots of the plants and crops to spread and absorb the required amount of nutrients. Soil compaction is a major problem primarily caused by human activities, micro-organisms, and other multiple factors.

Question

The ff are results of a field unit weight determination test

Volume hole 0.0016

Mass of moist soil from 3.10kg

Water content 12.20%

Mas dry 19.50

Determine the relative compaction in %

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

9. The results of a Standard Proctoretest is tabulated as follows: (CHECK PICTURE) Determine the maximum dry unit weight of compaction Determine the void ratio at the optimum moisture content Gs = 2.68 Determine the optimum moisture content Determine the degree of saturation at the optimum moisture content
3. The following table lists the results of a standard Proctor assay. Determine the maximum dry compaction density and the optimum moisture content. Also obtain the void ratio and degree of saturation for optimum moisture content. Assume Gs = 2.68.
For a silty clay soil given LL = 43 and PL = 18. Estimate the maximum dry unitweight of compaction that can be achieved by conducting a modified Proctor test. Use Eq attached.
The results of a standard Proctor test are given in the following table. Determine the maximum dry unit weight of compaction and the optimum moisture content. Also determine the moisture content required to achieve 90% of ꙋd (max).
Plot the moisture density curve and determine the maximum dry unit weight of compaction and the optimum moisture content.
For a granular soil, the following are given:●● Gs = 2.6●● Liquid limit on the fraction passing No. 40 sieve 5 20●● Percent retained on No. 4 sieve 5 20 Using Eqs. (5.4) and (5.5) attached , estimate the maximum dry density of compaction and the optimum moisture content based on the modified Proctor test.
The following results are obtained from standard compaction test for a soil, if Gs = 2.5 Water Content (%) 6.2 8.1 9.8 11.5 12.3 13.2 Unit weight (kN/m3) 16.9 18.7 19.5 20.5 20.4 20.1 Required: 1- The optimum water content (Wc %) 2- The maximum dry unit weight ( dry ) 3- The void ratio (e) 4- Degree of saturation (S %) 5- Find the weight of water needed to be added to 1 m3 to reach 100% saturation.
1. Draw the compaction curve using the following given data from a standard Proctor test. 2. From the compaction curve you drawn, determine the Optimum Moisture Content and the Maximum Dry Unit Weight.
A field unit determination test for the soil, yielded the following data. Moisture content = 12% and moist unit weight = 106 lb/cu.ft. Determine the relative compaction.
Assuming the fill soil does not change properties, how can the compated soil density exceed 100% standard proctor? a) Increased compaction energy b)Increased Strength c) Increased Plasticity Index d) Decreased permeability
Determine the density index of a soil having a natural void ratio 0.7. The void ratio of the soil in the loosest and most dense state is 0.85 and 0.4 respectively. Also, calculate the relative compaction.
A soil specimen having a volume of 0.012 m3 has a specific gravity of 2.60. It has a moist mass of 20.6 kg and a dried mass of 16.1 kg. Compute its void ratio.