The figure below shows a bracket plate to transmit a reaction of 150 kN at an eccentricity of 95 mm from the column flange. What will be depth of bracket plate required. Assume Fe410 steel grade and thickness of bracket plate as 10 mm. Also assume size of fillet weld = 6 mm and shop welding. 95 mm 1 150 kN d

The figure below shows a bracket plate to transmit a reaction of 150 kN at an eccentricity of 95 mm from the column flange. What will be depth of bracket plate required. Assume Fe410 steel grade and thickness of bracket plate as 10 mm. Also assume size of fillet weld = 6 mm and shop welding. 95 mm 1 150 kN d

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter7: Simple Connections

Section: Chapter Questions

Problem 7.11.10P

See similar textbooks

Similar questions

Which of the following most nearly gives the throat of a 9 mm fillet weld? a. 4.5 mm b. 6.4 mm c. 12.7 mm d. 7.4 mm
A flanged bolt coupling consists of six 1/2-in. steel bolts evenly spaced around a bolt circle 12 in. in diameter, and four 3/4-in. aluminum bolts on a concentric bolt circle 8 in. in diameter. What torque can be applied without exceeding 9000 psi in the steel or 6000 psi in the aluminum? Assume Gst = 12 x 10^6 psi and Gal = 4 x 10^6 psi.
A flanged bolt coupling consists of six ½-in. steel bolts evenly spaced around a bolt circle 12 in. in diameter, and four ¾-in. aluminum bolts on a concentric bolt circle 8 in. in diameter. What torque can be applied (kip-in) without exceeding 9000 psi in the steel or 6000 psi in the aluminum? Assume Gst = 12 × 106 psi and Gal = 4 × 106 psi.
A flanged bolt coupling consists of eight ½ -in. steelbolts evenly spaced around a bolt circle 12 in. indiameter, and six ¾ -in. aluminum bolts on aconcentric bolt circle 8 in. in diameter. What torquecan be applied without exceeding 15000 psi in thesteel or 10000 psi in the aluminum? Assume Gst =12 × 106 psi and Gal = 4 × 106 psi.
Calculate the maximum shear force in the welds and the required weld size in the given figure. Where P= 50kN X=60mm, Y=150mm, Z=100mm What is the maximum force on the weld in kN/mm? (2 decimal places) What is the required weld size considering E70xx fillet weld in mm? (rounded value)
8. determine the capacity of the details shown below.A992: Fy=50ksi, Fu=65ksiA36: Fy=36ksi, Fu=58ksieffective bolt hole diameter = bolt hole + 1/16"beam properties: tw=0.38 in., bf=7.07 in., tf=0.63 in.Fexx=70ksih) what is the flexural rupture capacity of the shear plate of the shear connection in kips? (2 decimal places)
A flanged bolt coupling consist of 9 steel bolts evenly spaced around a bolt circle 300 mm. in diameter and 6 bronze bolts on a concentric bplt circle 200 mm. in diameter. What are the sizes of bolts diameters for steel and bronze, if the torque applied is 6,000 N-m and without exceeding the stress of 60 MPa in the steel and 40 MPa for the bronze? The ratio of the bolt diameter db / ds = 0.50. For steel, use Gs = 83 GPa and for bronze, Gb = 28 Gpa.
The following tubular A36 steel shaft has an inner diameter of 25mm and an outer diameter of 35mm under the following loading condition. Determine the angle of twist of the end V. Consider: GA-36 = 75 GPa 1) What would happen if a solid shaft was used? 2) As a designer, do you recommend a solid or tubular shaft for the loading above? Why?
Material Strengths: Fy= 248 MPa, Fu= 400 MPa Method: Use ASD. A single angle L203X152X19 is welded (longitudinal and transverse welds) on one leg (shorter leg) to a gusset plate; thus, there are no holes. The length of the longitudinal welds is 150 mm. Which of the following most nearly gives the allowable tensile load (N) based on fracture on net area? CHOICES: 474 549 719 478 1424 1439 1099 957 719 949 712 732 366 1439
The angle 150x100x100 mm is connected to the gusset plate. The size of weld is 8 mm and using E70 electrodes. Fu = 438 MPa Question: a.) Find the length of the weld required at the toe of the angle. b.) Find the length of the weld required at the heel of the angle.
A steel bar 50 mm in diameter and 2 m long is surrounded by a shell of a castiron 5 mm thick. Compute the load that will compress the combined bar a totalof 0.8 mm in the length of 2 m. For steel, E = 200 GPa, and for cast iron, E = 100GPa. Note provide a diagram/figure. -Draw and label the diagram correctly, No diagram in the solution will be marked wrong. -Shortcut solution will be marked wrong.- Direction of the assumption of the equilibrium equation must be shown, no direction will be marked wrong.
If the structural frame is replaced to structural steel and the connections is to be designed, determine the following Determine the centroid of the weld measured from the given origin A. Determine the direct shear load in the welds. Determine the required size of the fillet weld(E60xx) if the maximum resultant load is 750,000 N/mm