The figure below shows a clawhammer as it is being used to pull a nail out of a horizontal board. A force of magnitude 180 N is exerted horizontally as shown. (Assume that the force the hammer exerts on the nail is parallel to the nail and perpendicular to the position vector from the point of contact. The x-component of this force's lever arm is 5 cm.) 30.0 cm Single point of contact /30.09 5.00 cm (a) Find the force exerted by the hammer claws on the nail. (Enter the magnitude.) 1247.07 Your response differs from the correct answer by more than 10%. Double check your calculations. N (b) Find the force exerted by the surface at the point of contact with the hammer head. (Assume the positive x-axis is to the right.) 1346.13 Your response differs from the correct answer by more than 10%. Double check your calculations. N 53.35 magnitude direction Your response differs from the correct answer by more than 10%. Double check your calculations.° counterclockwise from the +x-axis

The figure below shows a clawhammer as it is being used to pull a nail out of a horizontal board. A force of magnitude 180 N is exerted horizontally as shown. (Assume that the force the hammer exerts on the nail is parallel to the nail and perpendicular to the position vector from the point of contact. The x-component of this force's lever arm is 5 cm.) 30.0 cm Single point of contact /30.09 5.00 cm (a) Find the force exerted by the hammer claws on the nail. (Enter the magnitude.) 1247.07 Your response differs from the correct answer by more than 10%. Double check your calculations. N (b) Find the force exerted by the surface at the point of contact with the hammer head. (Assume the positive x-axis is to the right.) 1346.13 Your response differs from the correct answer by more than 10%. Double check your calculations. N 53.35 magnitude direction Your response differs from the correct answer by more than 10%. Double check your calculations.° counterclockwise from the +x-axis

University Physics Volume 1

18th Edition

ISBN:9781938168277

Author:William Moebs, Samuel J. Ling, Jeff Sanny

Publisher:William Moebs, Samuel J. Ling, Jeff Sanny

Chapter2: Vectors

Section: Chapter Questions

Problem 26P: In a tug-of-war game on one campus, 15 students pull on a rope at both ends in an effort to displace...

See similar textbooks

Similar questions

Using the same force table that you used, a student was given two forces and asked to find a single force that would produce equilibrium with the two forces. The two forces were given by providing one of the components and the angle the force made with the positive x- axis. The two forces were as follows: Force 1: Fx = −2.70 N; Theta = 220.0 degreees Force 2: Fy = 3.20 N; Theta = 60.0 degrees (a) For each force, calculate the magnitude of the force and the mass required to produce it. (b) Calculate the mass and its angle of application to produce equilibrium with these two forces. Please specify your angle as counterclockwise positive with respect to the positive x-axis.
The hamstrings pull on the tibia with a force of 510 N at 30 degrees to the bone: that is the angle between the force vector and tibia is 30 degrees. The distance along the tibia from the knee joint center to the tendon insertion is 3.5 cm. What is the magnitude of the force component that is parallel to the tibia?
The three concurrent force acting in the beam can be replaced with a single force , R, compute the magnitude and position of the resultant
The two forces shown act at point A of the bent bar Determine the resultant R of the two forces
If the forces on the beam are replaced by an equivalent Force-Position system, determine the distance d where the resultant force must be placed. F = 58 N, P = 97 N, Q = 18 N, a = 1.5 m, b = 1.5 m and c = 1.9 m.
A trapeze artist, with swing, weighs 800 N; he is momentarily held to one side by his partner so that the swing ropes make an angle of 30.0° with the vertical. In such a condition of static equilibrium, what is the horizontal force being applied by the partner?
A force of 500 nt is measured with a possible error of 1 nt. Its component in adirection 60◦ away from its line of action is required, where the angle is subject to an error of 0.5◦. What is (approximately) the largest possible error in the component?
The rectangular framework is subjected to the following non-concurrent system of forces: a 30lb- force below the origin, a 20lb-force 3ft above the origin and making an angle of 30°NE, a 100lb-force with a horizontal distance of 3ft and a vertical distance of 4ftfrom the origin and making an angle of 45° NW, a 60lb force with the same distance like the previous force but along the positive x-axis, and a 100lbs force 4ft to the right of the origin and making an angle of 60° SW. Determine the magnitude and direction of the resultant, as well as its moment arm relative to the origin.
A uniform plank of length 2.00 m and mass 30.0 kg is supported by three ropes, as indicated by the blue vectors. Find the tension in each rope when a 700 N person is d = 0.500 m from the left end
The figure shows an object of mass ?1 = 1.0 kg on an inclined frictionless surface. The angle of theinclined surface is ? = 25 with respect to the horizontal. The object of mass ?1 is connected by anideal string over an ideal pulley to a second object of mass ?2 = 2.05 kg on a horizontal frictionlesssurface below the overhang that is formed by the inclined surface. Furthermore, an external force ofmagnitude ???? = 10 N is exerted on the object with a mass ?1. We observe both objects accelerate. i. Draw separate free-body diagrams of all the forces acting on the two objects ii. Calculate the tension in the string connecting the two objects.
Forces F1, F2, and F3 act on the structure depicted in the figure, shown in an overhead view. We wish to put the structure in equilibrium by applying a force, at a point such as P located a distance d from F1, whose vector components are Fh and Fv. We are given that a = 2.1 m, b = 2.6 m, C = 1.15 m, F1 = 18.05 N, F2 = 11.05 N, and F3 = 4.85 N.Find Fh.
Using the same force table that you used, a student was given two forces and asked to find a single force that would produce equilibrium with the two forces. The two forces were given by providing one of the components and the angle the force made with the positive x- axis. The two forces were as follows: Force 1: ?? = −2.70 ?; ? = 220.0 degreees Force 2: ?? = 3.20 ?; ? = 60.0 degrees (a) For each force, calculate the magnitude of the force and the mass required to produce it. (b) Calculate the mass and its angle of application to produce equilibrium with these two forces. Please specify your angle as counterclockwise positive with respect to the positive x-axis.